Unable to reach brewpi-script
Hello, I appreciate if I can get some help.
I used brewpiless in the past and I recently noticed this application and it's very attractive so I can manage both fermentation chambers.
I used a breadboard and a new Wemos D1 Mini Pro to install and test the app, however it looks like the controlled does not communicate with the Raspberry Pi on USB serial:
-Raspberry Pi 3 with fresh NOOBS install, Fermentrack - one command install, 5V 3A powered
-Wemos D1 Mini Pro (SERIAL not WiFi setup), Flash with Fermentrack - Non-Node MCU ESP8266 (Default Flash Mode) (I tried Node MCU also with no success but the sreenshots are from the Default Flash Mode), 5V 3A powered separately from RPI
-2x rellay board
-4x temp sensors DS18B20 (already wired together but will only use 2)
-20x4 display
Before flashing the ESP I ran the test script and it recognized the replays and temp probes without any issues.
It looks like Fermentrack does not communicate with the controller and I can not setup the pins, please see the screenshots and the log below.
The display shows status Off and Idle time.
Whatever I'm doing, I'm consistently doing it wrong because I get the same results with two different controllers.
I tried wireless instead of serial and same thing, I can not access the pins. Here is how the wireless log looks like:
Mar 21 2020 17:36:12 Connection type WiFi selected. Trying TCP serial (WiFi)
Mar 21 2020 17:36:12 Unable to resolve hostname ESP439054.local. Exiting.
Mar 21 2020 17:36:20 Connection type WiFi selected. Trying TCP serial (WiFi)
Mar 21 2020 17:36:20 Connecting to BrewPi ESP439054.local (via 192.168.50.65) on port 23
Mar 21 2020 17:36:29 Successfully connected to controller.
Mar 21 2020 17:36:29 Notification: Script started, with no active beer being logged
Mar 21 2020 17:36:39 Checking software version on controller...
Mar 21 2020 17:36:39 Found BrewPi v0.2.4, running commit 00000000, running on an ESP 8266 on port 192.168.50.65:23
Mar 21 2020 17:36:39 BrewPi version received was 0.2.4 which this script supports in 'legacy' branch mode.
Mar 21 2020 17:36:40 Installed devices received: []
Mar 21 2020 17:36:47 Available devices received: [{"i": -1, "t": 0, "c": 1, "b": 0, "f": 0, "h": 2, "d": 0, "p": 12, "v": 69.123, "a": "28FFB22393160497", "j": 0.0}, {"i": -1, "t": 0, "c": 1, "b": 0, "f": 0, "h": 2, "d": 0, "p": 12, "v": 69.236, "a": "28FF0927931604A6", "j": 0.0}, {"i": -1, "t": 0, "c": 1, "b": 0, "f": 0, "h": 2, "d": 0, "p": 12, "v": 69.574, "a": "28FFA3D892160468", "j": 0.0}, {"i": -1, "t": 0, "c": 1, "b": 0, "f": 0, "h": 2, "d": 0, "p": 12, "v": 68.898, "a": "28FFB722931604CA", "j": 0.0}, {"i": -1, "t": 0, "c": 1, "b": 0, "f": 0, "h": 1, "d": 0, "p": 16, "x": 1}, {"i": -1, "t": 0, "c": 1, "b": 0, "f": 0, "h": 1, "d": 0, "p": 14, "x": 1}, {"i": -1, "t": 0, "c": 1, "b": 0, "f": 0, "h": 1, "d": 0, "p": 13, "x": 1}]
If I do a Debug Connection, the following fail:
Controller Response Test ESP439054.local Failed
Controller Response Test 192.168.50.65 Failed
Just to mention, I was able to add an iSpindel and it's collecting data without any problems.
I don't know what else I can try or check and I appreciate if I can get any suggestions.
Thank you!