Aw, it's all good, and the fact you added that feature speaks well...
Cheers!
Cheers!
Glad that it works for you.
I extremely feel sorry for insisting that static IP function existed without checking it.
No worries. I did find out via online searching that many routers allow you to do exactly what you said. I apparently just have old stuff that didn't have that built in...
I appreciate your effort in adding the feature!
Just starting with brewpiless.
I actually have one of those v3 Nodemcu boards. I started with just one sensor, and everything seems to work fine. However, at the moment of attaching a second sensor, brewpi page seems to freeze, with failed to connect to the server.
I am using an usb input of 5V and 3A, maybe has it not enough potence? I am planning on getting a NodeMCU v2.
Will it work? Anyone there with same issues?
Thank you!
Still waiting parts for this (the slow boat from china probably sunk) any way I note your looking to add support for ispindel, was wondering how hard it would be to also add support for pressure sensing and control? I got some code for arduino to use these sensors but note @ 2.5bar (36.3 PSI) the output would be well over 3.3v (4.5v), now usually you wouldn't exceed 1.5 bar (21.75 psi) which would come it at 3.357v, the A0 pin is free but would this sensor blow the board? Could used the door sensor pin to fire the relief solenoid. Pressure fermenting is becoming more popular would be nice to have the whole lot controlled and plotted with one device.
Ed: bad math/ more detail
Let me know if you would like to see the code.
Pressure fermenting is not for just at the end of fermentation. It is quite handy at the start of fermentation as it inhibits ester formation, this also allows for higher fermentation temps and therefore faster ferments if one so chooses. Say a lager from grain to brain in 7 days is not unheard of using these methods. Plenty of info out there on the interwebs.
Agree the digital Hydrometer would be first priority!
Thats the point presure sensor and solenoid valve replace the spunding valve and controlled to within 1psi. And you can log it making it repeatable. Worst thing with pressure fermenting is finding a quality spunding valve.( commercial units are around $300).
Electronically monitoring pressure and opening and closing a solenoid to maintain a set point seems logical and simple compared with some of the spunding valves I've had.
I would hate to have something as important as pressure relief left up to a computer or controller ... Think power outage.
Is there any way in the setup procedure to change the pinouts to match Thorrak's pcb?
D0 - Heat
D1 - I2C SCL
D2 - I2C SDA
D3 - Buzzer (currently unsupported)
D4 - N/C
D5 - Cool
D6 - OneWire Data
D7 - Door (Untested)
How can I tell which pins need to be changedYou need to edit Config.h and change the corresponding definition.
I should have my oled this week I think. I'm looking for some direction on hooking it up. I've got 4 EPS's working fine, but I'm not familiar with a screen at all.. And I doubt it's just plug in the wires and go.. I'm gonna work on building the acrylic box this weekend. All parts, other than the oled, are tested and ready for the job. The oled is just eye-candy. If your gonna do do it right!!
I"m hoping pocketmon will guide me with this one....
#define BREWPI_OLED128x64_LCD 1
//#define BREWPI_IIC_LCD 1
Is there any way in the setup procedure to change the pinouts to match Thorrak's pcb?
D0 - Heat
D1 - I2C SCL
D2 - I2C SDA
D3 - Buzzer (currently unsupported)
D4 - N/C
D5 - Cool
D6 - OneWire Data
D7 - Door (Untested)
#define coolingPin NODEMCU_PIN_D5
#define heatingPin NODEMCU_PIN_D7
#define doorPin NODEMCU_PIN_D4
#define BuzzPin NODEMCU_PIN_D0
#define coolingPin NODEMCU_PIN_D5
#define heatingPin NODEMCU_PIN_D0
#define doorPin NODEMCU_PIN_D7
#define BuzzPin NODEMCU_PIN_D3
#define coolingPin NODEMCU_PIN_D5
#define heatingPin NODEMCU_PIN_D0
#define doorPin NODEMCU_PIN_D7
#define BuzzPin NODEMCU_PIN_D3
Will pin 3 still work as the wakeup button if changed to the buzzer?[/QUOTE]Change it to
Code:#define coolingPin NODEMCU_PIN_D5 #define heatingPin NODEMCU_PIN_D0 #define doorPin NODEMCU_PIN_D7 #define BuzzPin NODEMCU_PIN_D3
#define WAKEUP_BUTTON 1
#if WAKEUP_BUTTON
#define WakeupButtonPin NODEMCU_PIN_D4
Will pin 3 still work as the wakeup button if changed to the buzzer?
#define WAKEUP_BUTTON 1
#if WAKEUP_BUTTON
#define WakeupButtonPin NODEMCU_PIN_D4
@pocketmon, Curious if you plan, or know, if the Tilt Hydrometer can/will be implemented?
@pocketmon is there a erase all/ reset cmd?
I've surveyed the communication 'protocol' of TILT.
I will say it's easy to support TILT if you can find a module that ESP8266 can use to support BLE.
The only BLE module I know is HM-10, and I happened to have one. To support iBeacon, which is the way TILT broadcast the data, v540 or higher is necessary. well.Let's jump to the conclusion, I bricked the module and it's not easy to buy a HM-10 running V540.
Buying a Raspberry Pi Zero W might be a better solution.
I have a question on the OTA update.. When I go to the page, it ask me to choose a file...? Where do I locate the file to complete the OTA?
It makes perfect sense really adjusting temp by gravity.
Maybe as an a UI option set target FG at x% attenuation raise to y-temp.
What could also be good would be a RAG system for fermentation Red being OG and then Amber being expected attenuation and green being FG after 2-3 days but also indicating time for dry hop.
Just my starter for 10.
Would love this to merge with Thorraks too though
Enter your email address to join: