Where did you get the vent Hood?
Where did you get the vent Hood?
It sets in a 240 SQ. ft building I built myself spray foam insulation all around (with a little help from my friends). It has a mill room and a fermentation room. I designed and built the system myself. Works great
Nice. I work at 80/20 [emoji3]Great job!
I love the anodized extrusion from 80/20, I used a few hundred feet all over my toy brewery.
Where did you get the vent Hood?
Unless there are pics of said “brew shed” it doesn’t exist. Post them up so we can all see your brew space and drool.
Unless there are pics of said “brew shed” it doesn’t exist. Post them up so we can all see your brew space and drool.
Thanks!I made it out of plywood, 2x4, j-channel, screws and caulk. I can’t remember if I found a thread here on HBT, or TheElectricbrewery.com. I’ll search around. White part is FRP panel.
Update:
Found the HBT thread: https://www.homebrewtalk.com/forum/threads/5-1-2-foot-diy-hood-for-approx-75.371453/
Can you see this? I'm much better at brewing than this F*#king phone.
Did you see the pictures? This is the glass you need Halfempty.Unless there are pics of said “brew shed” it doesn’t exist. Post them up so we can all see your brew space and drool.
Hotrod from Brewhardware. I have one in my system. Nice!Here’s my RIMS system with electric HLT.
Couldn't open it. With a name like Tower of Power the pic was blocked because it either resembles a part of the male Anatomy, Frank Zappa complained, or John Blickmann has the patent for his tower of power. Hmmmm?
Brew tree I designed and built in 2007. Had the stand professionally welded since I am horrible at that skill. We call it the "Tower of Power. Each vessel has a 55,000 BTU burner (propane).
Isn't your oxygen tank a bit close to the burner, or is it just there to have it in the pic? Very nice setup though.
Let's try this again. First post didn't show the photo....
Brew tree I designed and built in 2007. Had the stand professionally welded since I am horrible at that skill. We call it the "Tower of Power. Each vessel has a 55,000 BTU burner (propane).
View attachment 573086
Now I see it, looks nice.Let's try this again. First post didn't show the photo....
Brew tree I designed and built in 2007. Had the stand professionally welded since I am horrible at that skill. We call it the "Tower of Power. Each vessel has a 55,000 BTU burner (propane).
View attachment 573086
Just about to add new video about the smoker and grill stuff.. most likely tomorrow! Hope you enjoy!I watched your video, love the simplicity of the mash stirrer! And really curious about your BBQ, smoker stuff...you should join us over here
https://www.homebrewtalk.com/forum/index.php?threads/637254/
Looks very nice. I have a sink something like yours.Here’s a system I cobbled together to hold me over until I get my electric brewery installed and running. Been slow returning to brewing since my move from south Jersey to Florida.
That is beautiful! Does it do time travel as well?
AMAZING! What a thing of wonder and joy.
First post in a couple years just because I saw this (I've been brewing the whole time).
You need to ask?That is beautiful! Does it do time travel as well?
I used the same size on my old gas rig and had no supply problem. The point that did give me issues was the valve I used. I used a regular gas ball valve which did not have as smooth an operation as a needle valve. The ball valve dumps too much gas all at once and can blow out the pilot light and remove your eyebrows.Will these 1/4" ID 2 foot lenth hoses fit the bill, or will it be too small to run a BG14?
Back says rated for 40k BTU. They were on clearance for $5 at Home Depot, so I shot first and am asking second.
I used the same size on my old gas rig and had no supply problem. The point that did give me issues was the valve I used. I used a regular gas ball valve which did not have as smooth an operation as a needle valve. The ball valve dumps too much gas all at once and can blow out the pilot light and remove your eyebrows.
Just a manual switch. The pilot light was before the solenoid. It could just as well have been a PID and relay. I was planning to add an electric control panel but decided to go all electric and built a building to put it in so I did away with propane. Now I need to sale the gas rigBrewbuzzard, what did you use to control the solenoid?
Loving the mail boxes - as long as the backs were cut out.
You can easily cook a Chugger motor to thermal shutdown with inadequate ventilation...
Cheers!
Not sure what you mean by back flow when the pump stops. If needed, I'll close a valve somewhere.The backs are gone...and now so is the bottom. Maybe a stronger box would support it better but after a run through, I wasn’t happy with the support. The pumps are now mounted to the frame with the arches installed as covers. I probably would fare better with just rolling steel, but these were cheap enough to cut apart.
Other issues I’m running into:
1. Back flow into pots when I stop the pump
2. Best way to clear the lines after shutting off the pump
Not sure what you mean by back flow when the pump stops. If needed, I'll close a valve somewhere.
As far as wort in lines, I chalk that up as lost liquid unless I can salvage some of it with out spilling it all.
When you stop pumping, the liquid will flow until the pressure due to gravity is equalized. If you've been pumping uphill, then yes, backflow happens. Get in the habit of shutting the discharge valve then immediately stopping the pump.When I stop the pump, the liquid start flowing back up into my mash tun. I just need to remember to close valve first, I just wasn’t expecting that to happen.
Enter your email address to join: