nyer
Well-Known Member
I think I might have to add something like that to my MLT. I hate scooping out the grain. I would add some type of hitch pin on the pivot so the MLT could be removed quickly and easily.
Sanke Tippy Dump MLT
- Thread starter lschiavo
- Start date
Help Support Homebrew Talk:
OP
OP
Yes, my thoughts exactly. I bought some pins. I just used the nuts and bolts for the mockup.
nyer
Well-Known Member
I can picture a pin I saw at lowes that would be perfect, it's long enough to reach through both brackets and it has a nice handle on one end with holes in the others for a key. I think it's used for farm equipment and should be very strong.
Oooh, a gift from Texas! But probably not seafoodI'm exited!
I'd LOVE to bring you back some seafood. Unfortunately (well, actually, fortunately for us) it's over 80 degrees and I just have no way to keep it for 3-4 days for the trip home. We cooked up some random stuff we still had yesterday- one live blue crab, one small flounder, some other stuff- and it was awesome. I do wish I could bring home a sack of oysters, though.
With the removable pin, that could mean that I could still use my old MLT (I'm thinking for real small grain bills, like a 5 gallon mild), as well as emptying the MLT and then hosing it out. You know what might be helpful? (Just thinking out loud here). One of those "handles" like you put on the side of the canoe with some weld or some rivets? Does that make sense? One of those on each side near the top might make handling it and lifting it easier, if it's doable. My friend Roger put them on his canoe, to carry it down to the river. Would that be something that might work?
OP
OP
A single pin was my first thought. I could not find anything like you describe around here but it sounds like it would work great. I did find some 3/8 rigid conduit that fits through the holes in the strut angle (old lighting fixture downrod with a flange on one end). I may end up using that with one key.
OP
OP
I'd LOVE to bring you back some seafood. Unfortunately (well, actually, fortunately for us) it's over 80 degrees and I just have no way to keep it for 3-4 days for the trip home. We cooked up some random stuff we still had yesterday- one live blue crab, one small flounder, some other stuff- and it was awesome. I do wish I could bring home a sack of oysters, though.
With the removable pin, that could mean that I could still use my old MLT (I'm thinking for real small grain bills, like a 5 gallon mild), as well as emptying the MLT and then hosing it out. You know what might be helpful? (Just thinking out loud here). One of those "handles" like you put on the side of the canoe with some weld or some rivets? Does that make sense? One of those on each side near the top might make handling it and lifting it easier, if it's doable. My friend Roger put them on his canoe, to carry it down to the river. Would that be something that might work?
I guess I will just have to visit you guys out there someday to get some of that seafood.
Yes, you should be able to swap out MLT's. The only issue may be the false bottom. I was planning on modifying it for the keg but we may be able to keep it useable in both.
Handles would be very "handy". I was planning to run to Ace and get something when we put this together. I was thinking of at least a handle on the back of the keg for something to hold onto while tipping the keg. We could add one on the front also for carrying.
![Craft A Brew - Safale S-04 Dry Yeast - Fermentis - English Ale Dry Yeast - For English and American Ales and Hard Apple Ciders - Ingredients for Home Brewing - Beer Making Supplies - [1 Pack]](https://m.media-amazon.com/images/I/41fVGNh6JfL._SL500_.jpg)
nyer
Well-Known Member
http://www.google.com/products/cata...X&ei=3MVgT7OzFoXm0QH9mJzMBw&ved=0CJwBEPMCMAM#
This is the pin I saw at lowes. They have a drawer full of different ones in the hardware section.
This is the pin I saw at lowes. They have a drawer full of different ones in the hardware section.
stamandster
undefined member
Looks great! How did you get the last bit of the collar off?
I think it's awesome. I'd recommend putting a hefty handle on the top on the far side of the opening to initiate the dump process and keep it controlled as you lower it to the garbage can. You'll also do well if you make a curved piece of stiff rubber and attach a handle like a hoe to squeegee the grain off the walls.
Also, don't overlook the plumbing when considering the dumping action. It may seem odd, but attaching the output ball valve to the front of the stand and then connecting it to the tun with silicone tubing would be one way to avoid having to notch out a large portion of the stand.
Also, don't overlook the plumbing when considering the dumping action. It may seem odd, but attaching the output ball valve to the front of the stand and then connecting it to the tun with silicone tubing would be one way to avoid having to notch out a large portion of the stand.
OP
OP
Ahhh, someone noticed
That took a bit of trial and error. I finally noticed after way too much grinding that the weld that attaches it to the keg is at the very end of the collar and is quite thin. I just ground that edge until it was loose. I think when I cut mine, I will just grind the collar off instead of the sawzall cutting.
OP
OP
Thanks! The handle is in the plans and I'm sure will be necessary. The squeegee is a great idea. I had not considered a tubing connection to the bottom. That sounds like it may work out great.
You're always welcome here- as you should know by know.
The FB can be modified- I have an extra, I'm pretty sure. One I had before the electric MLT and one that came with the "new" MLT. Even when we swapped the MLTs for the non-cutout one, I think we kept the same FB. So unless I gave that old 12" FB away, I should still have it in the basement.
Junkster
Well-Known Member
On my old rig, the MLT was bolted to a frame made from steel angle and the whole thing was hinged on 2 7/16" bolts which slid inside of whatever steel pipe has close to that ID and it was plenty strong and worked fine.
If you want removable pins, I think someone already mentioned farm supply stores. They sell a variety of hitch pins with the matching sleeves / bushings for a nice fit.
If you want removable pins, I think someone already mentioned farm supply stores. They sell a variety of hitch pins with the matching sleeves / bushings for a nice fit.
OP
OP
I think I can visualize your old setup but pictures would help if you have any.
The Farm supply store is 30 miles away. I'm not making a special trip for a pin but the one posted earlier does look nice.
OP
OP
Really? A spare false bottom?!?!? Only the hard core brewers keep one of those on hand. It does take quite a few batches to wear one out.
You've seen my basement. I probably have a lot of spare things. I have a spare immersion chiller for sure, and a spare 5 gallon MLT (with false bottom) and a spare 10 gallon MLT(with false bottom, I think), and a spare HLT and a spare 30 gallon BK. It's like your family's storage barn, but with less space. I can probably scrounge up several things if I haven't given them away!
I cannot imagine you having ANY problems with that design as far as a dump goes. The center of gravity is low as it can go and it is stupid simple! I'm not sure where the concern comes from with the design. 1/2 in bolts, looks like .157-.187 thick hinges...Should handle it no problem.
I personally would be tempted to add a stop at the bottom of the travel for the MLT and if you were really concerned about the strength, add a gusset to the bottom angle for additional strength. But I would try it like it is first..It's not like these options cannot be added later after a cold test run.
Good job!
I personally would be tempted to add a stop at the bottom of the travel for the MLT and if you were really concerned about the strength, add a gusset to the bottom angle for additional strength. But I would try it like it is first..It's not like these options cannot be added later after a cold test run.
Good job!
OP
OP
Thank you. The stop is something I have been thinking about. I will be digging around for something to make that work. I think the angles will be ok. I have a feeling that the front rail on Yooper's stand may need a little beefing up.
"stupid simple", I like that! I really enjoy building stuff like this. The challenge of trying to come up with something as simple, cheap and durable as possible is actually sort of fun. It usually involves sitting with a homebrew and staring at it for a while which for me can be great entertainment
OP
OP
That should work well. I was also thinking of some sort of rubber bumper thingy mounted to the front rail of the stand. Off to dig through my piles of junk...
Junkster
Well-Known Member
I used chains on my old one to limit the travel..... I'll try to find some pics.
OP
OP
Okay, we finally got around to installing this thing. The only issue was the o-ring on the tri clover to sanke fitting would not seal completely...just a small leak. I am going to try to clean up the sanke side of the fitting with my random orbit sander as it had a few nicks in it that are probably causing the leak. If anybody has advice to offer to fix this problem, I'm all ears.
No handle or stop yet. Yooper is going to brew with it first and we will make any modifications after a trial run. Here's some pics:
No handle or stop yet. Yooper is going to brew with it first and we will make any modifications after a trial run. Here's some pics:
OMG- I just saw my skimpy bathrobe hanging there. That's hysterically funny. I should have cleaned up the brewery a little bit!
I'm so excited about brewing on this! As soon as I get over "The Plague", I'm going to brew. I will shoot for Saturday.
Bob was impressed for a couple of reasons. One, he's had the heebie jeebies about mashing in plastic all this time, but we really didn't have a good alternative until the keg came up. Two, it's shiny! Three, he thinks it will make hauling out the wet grain easier and make clean up easier. (He's the MLT emptier and the MLT cleaner).
I'm thrilled, except for the minor leak. And I know we'll get that sorted out!
I'm so excited about brewing on this! As soon as I get over "The Plague", I'm going to brew. I will shoot for Saturday.
Bob was impressed for a couple of reasons. One, he's had the heebie jeebies about mashing in plastic all this time, but we really didn't have a good alternative until the keg came up. Two, it's shiny! Three, he thinks it will make hauling out the wet grain easier and make clean up easier. (He's the MLT emptier and the MLT cleaner).
I'm thrilled, except for the minor leak. And I know we'll get that sorted out!
OP
OP
HA, I didn't notice the bathrobe until I posted the pic. It could have been worse...it could have been Bob's skimpy undies
I'm sure we'll have a few modifications to make but we will get it ironed out.
I've never played around with a triclover to sanke neck connection before, but does the oring sit in the recess on the triclover adapter? And if so, does it also sit correctly on the ledge of the sanke neck? It seams to me that the oring would have to be pretty well centered on that rather small flange. I wonder if a donut shaped piece of thin rubber wouldn't be a better gasket for that situation.
OP
OP
The o-ring seems to be in the right place for a seal...but obviously something is wrong. A thin silicone gasket may be the ticket. The triclover to triclover gasket is too thick to close the clamp. I really did not expect a leak here
The o-ring seems to be in the right place for a seal...but obviously something is wrong. A thin silicone gasket may be the ticket. The triclover to triclover gasket is too thick to close the clamp. I really did not expect a leak here
I used an exacto knife to remove the ridge on the sanke side of the o-ring, sealed up water-tight.
OP
OP
You know, I did try that but it was still too thick to close the clamp...??
I've successfully trimmed the ridge off of a regular tri-clamp style gasket on a filter screen too. The right kind of gasket is available from St. Pat's. Made for this application. Avoid radial scratches the go across the sealing surface.
Similar threads
