What kind of fermentor are you using..

[bracconiere]

I have 8 of those and love them.

You wouldn't know a good replacement for the o-ring, would you? mine got old and cracked....

 

[melp]

hey guys im thinking about upgrading to a conical fermentor... what are you using??

I'm into basics, 5 gallon plastic and towel. Rack to a carboy at 1.015

 

[drx2]

I think that works good, the gasket can be kinda a bear to get inplace but not too bad. one thing that i really didn't like was the butterfly valve, it was fairly aggressive no matter what i did, so I eliminated it, I got a mason jar lid with an 1 1/2" tri clamp that I installed and added a 3/4" ball valve so that when I want to drain the trub and whatever else I have a ball valve and can dump slowly and not introduce a jar of oxygen to the fermenter through the beer. Overall I really like it, easy to clean, easy to use, and I like that it is clear, I'm one of those people that likes to see the fermentation process

I have a catalyst and really like it. Your mod to get rid of the butterfly valve is a great idea. Do you bottle or keg? The clear bottling attachment is very convenient because it fits my bottling wand tubing. The larger diameter barbed fitting on the ball valve Is good to dump trub. Is there a reducer to fit the smaller tubing of the bottling wand, or can you swap out for a smaller sized barb fitting while still on the fermentor? Any other ideas? Thanks for sharing your great idea.

 

[user 254557]

Thank you, I both bottle and keg, I have a 3/8" barb fitting for kegging and a 1/4" for the smaller bottling wand, thats the great part of a standard size ball valve like mine, its super easy to get fittings for just about anything that you would think of. like I said the catalyst is a great product but my first mod to it was the lid, i really hated how the center of the lid convexes down almost into the fermenter, my issue with this is that the high krausen would contact this lid and find its only way out of a pressurized vessel, the airlock. The top of the lid has a shoulder on it that is about 1 1/2" wide so I drilled a couple 3/8" holes in it and added airlock gaskets to those spots so I can have two airlocks, now they can bubble away without getting plugged up, and the center one i plug with a solid bung.

 

[Dog House Brew]

You wouldn't know a good replacement for the o-ring, would you? mine got old and cracked....

I don’t, I’m guessing you could find silicone cord or use a silicone caulk.

 

[Immocles]

I saw a person or two mention fermonsters. I've read that the plastic is quite thing, Is this a major issue? I worry that the thin plastic around the spigot would be extra leaky? I've gone back and forth on getting a 3G for myself, but I ignored the reviews on the bmb universal lid and kind of regret that (still works fine, the duct tape gives it some charisma..). But I don't wanna do the thing same twice.

 

[bracconiere]

I don’t, I’m guessing you could find silicone cord or use a silicone caulk.

thanks for the suggestion...But i'm already out $24 trying to find something, and the feed store sells the complete brand new bucket for $20 new....(homebrewer cheap syndrome again!, lol)

 

[mirthfuldragon]

I saw a person or two mention fermonsters. I've read that the plastic is quite thing, Is this a major issue? I worry that the thin plastic around the spigot would be extra leaky?

I have three of the 7g ones and I like them. No leaks. The triangular (ish) spigot o-ring goes on the inside with the flat part against the plastic wall. There is also a trick to installing the lid gaskets, so watch a youtube video on how to do it correctly - I screwed it up the first time.

 

[lorne17]

I actually use a closed fermentation system. I ferment under low pressure in a 1/4 barrel (7.75 gal) keg with a spunding valve. I love it because the beer doesn’t see oxygen until it hits my pint glass from the serving keg. I can transfer kegs really easy by using CO2 and pushing from the fermenting primary keg to a clean secondary keg with dry hops or flavoring.

It’s improved my beer for sure! I actually sold my FastFerment because it was collecting dust.

Let me know your thoughts or if you use a spunding valve!

 

[mirthfuldragon]

I actually use a closed fermentation system. I ferment under low pressure in a 1/4 barrel (7.75 gal) keg with a spunding valve.

Out of curiosity, how much of a hassle is it in practice to deal with commercial keg spears and cleaning, at the homebrew level?

 

[lorne17]

Out of curiosity, how much of a hassle is it in practice to deal with commercial keg spears and cleaning, at the homebrew level?

It's actually not that bad. Once you get the hang of using two small flat head screwdrivers, it's pretty quick and easy to take the ring out that holds the spear in (sorry I don't know the formal names). Then I usually soak it in PBW for a bit and rinse it out. Haven't had any problems. I use a brush in the spear to get everything out.

Putting it back to gather is actually easier, just a pair of pliers to pinch the ring back in place.

Little effort to ensure no oxygen will hit my beer!

Hope this help,
Lorne

 

[lorne17]

It's actually not that bad. Once you get the hang of using two small flat head screwdrivers, it's pretty quick and easy to take the ring out that holds the spear in (sorry I don't know the formal names). Then I usually soak it in PBW for a bit and rinse it out. Haven't had any problems. I use a brush in the spear to get everything out.

Putting it back to gather is actually easier, just a pair of pliers to pinch the ring back in place.

Little effort to ensure no oxygen will hit my beer!

Hope this help,
Lorne

So I needed to clean my fermentation keg and just walked through the steps.

1. Remove all CO2 in keg before removing spear and ring.
2. Use two small flat head screw drivers to pry ring out. Once it’s started it’s easy. I searched YouTube for it.
3. Remove spear and rinse all trub out.
4. I then have a 5 gallon bucket from Home Depot and a high pressure water pump from Horrible Freight. I got some PVC pipes and found a tutorial online to make a T to easily clean out my keg and or car boys (if i used mine anymore).
5. I use no perfume oxi-clean and super hot water. Submerge the pump
In the bucket and then a bit extra.
6. Flip keg over on top of the PVC sticking up and turn pump on (don’t do this before your keg is on or you’ll have water everywhere).
7. Let it run for 20 mins or so.
8. Then do the same for water to rinse clean.
9. You’re done just sanitize it before you ferment in it again!

Hope this helped! I tried to do a video but it was a failure so I wrote it out.

Hope this helps,
Lorne

 

[mirthfuldragon]

Hope this helped! I tried to do a video but it was a failure so I wrote it out.

Thank you very much for the write-up. I was wondering about how it was in a practical sense - I have watched videos and seen how it is done, and it seems simple enough, so I was more interested in how it works as a practical matter, such as whether it was something you got annoyed doing or whatnot. Seems like it is simple enough, so I will have to keep my eye out for some quarter barrel kegs. Thank you again!

 

[lorne17]

Thank you very much for the write-up. I was wondering about how it was in a practical sense - I have watched videos and seen how it is done, and it seems simple enough, so I was more interested in how it works as a practical matter, such as whether it was something you got annoyed doing or whatnot. Seems like it is simple enough, so I will have to keep my eye out for some quarter barrel kegs. Thank you again!

It’s not super simple by any means. But once you do it a few times you get the hang of it. Overall worth it since my beer is much better with this spunding process.

Also 1/4 barrel kegs are hard to come by. It took months before one showed up on CraigsList. I had a notification set so it would tell me when one came up. It was months of weeding through alerts just on kegs for sale or kegerators. Then finally a 1/4 barrel showed up and I pounced!

I actually had a half barrel for the time being and it’s just so dang cumbersome to clean and handle.

Hope that helps,
Lorne

 

[TallDan]

Also 1/4 barrel kegs are hard to come by. It took months before one showed up on CraigsList. I had a notification set so it would tell me when one came up. It was months of weeding through alerts just on kegs for sale or kegerators. Then finally a 1/4 barrel showed up and I pounced!

They aren't as common to find used in the normal homebrew channels, but they're far from hard to come by. You can buy them new from stout tanks and elsewhere. The market for new and used sankes is very healthy with craft brewers buying and selling constantly.

 

[lorne17]

They aren't as common to find used in the normal homebrew channels, but they're far from hard to come by. You can buy them new from stout tanks and elsewhere. The market for new and used sankes is very healthy with craft brewers buying and selling constantly.

Good to know thanks! I know it was hard to find in Colorado!

Buying new is always possible at around $120 from what I found.

 

[Tobor_8thMan]

Always stainless for primary and secondary. Easy to clean and sanitize. Durable unless I do something stupid.

 

[Dog House Brew]

thanks for the suggestion...But i'm already out $24 trying to find something, and the feed store sells the complete brand new bucket for $20 new....(homebrewer cheap syndrome again!, lol)

I do have a few that are cracked, if I find the source I’ll keep you in mind.

 

[TallDan]

Good to know thanks! I know it was hard to find in Colorado!

Buying new is always possible at around $120 from what I found.

$120 with shipping for buying one from stout. In Colorado, I’d be surprised if you couldn’t get new slim quarters for $90 and sixtels for $75 or less.

For example:
https://www.probrewer.com/classified-ad/ambrach-kegs-new-pricing/

 

[bracconiere]

I do have a few that are cracked, if I find the source I’ll keep you in mind.

Thanks! i'll do the same, just seems like a waste to have to buy a whole new bucket for what probably is a 50 cent foam gasket...

 

[Zooksta]

I upgraded to the Spike CF15 with the temp control bundle, and I built a glycol chiller out of a 5,000 BTU window AC unit. Just got my first batch into it on Saturday, loving it so far.

 

[Budz]

I'm still using a 20 year old More Beer 12.5 gallon conical that I recently had customized. I found someone nearby that doesn't charge much for sanitary welding of stainless. I replaced the racking arm and had a TC flange welded to the bottom to eliminate all threaded fittings, and I had 3 TC flanges welded to the lid for a blowoff fitting, a thermowell, and a sight glass/window (it came with a single small hole drilled in the lid). I keep it in a homemade insulated fermentation chamber powered by a dorm room frig with the door removed, and a computer fan in the chamber to keep the cold air circulating. The only thing I don't like is that 20 years later, More Beer is still using the same garbage lid gaskets that keep coming apart.

 

[elbinwyp]

I ferment in 5 gallon cornys. Relatively inexpensive, pressure regulated and set up by default to pressure transfer. Fit nicely in my keezer set at 40 degrees. Ferment with controllable heat wrap at whatever temp I want and simply turn it off to cold crash. Add 5# co2 and send it to the serving keg. So simple it’s a bit silly.

Do you cut the serving post above trub level?

 

[Anyhowe]

Do you cut the serving post above trub level?

Usually to 1/2 inch.