Show us your sculpture or brew rig

[ronstar55]

Where did you get the shelving?

Menard's - don't know if they have them in your area - maybe Home Depot / Lowes, etc has something similar

 

[ronstar55]

The mythological "finished brew rig"

So what's your next enhancement going to be?

Haven't thought about it yet - its only been a week since I finished the last revision. Maybe a sight glass or 2. Measuring by sticking a ruler in the kettle just doesn't seem right.

 

[cheese]

That's my circulated BIAB Brewery.

Based one 10 gallon electric Urn, 3000W heating power, march pump at the bottom.

The bottom , pump and electricity .

Two operation modes-
1. temperature control with PID controller
2. ON/OFF with simerstat , the white noob on the left, to control the heating power
toggling modes with the switch on the right

currently circulating from a hole close to the side of the urn to one in the middle, silicon tubing connected to aeration wand.
I want to plug to hole in the middle and move the silicone tubing out side the urn.

pump inlet on the right and drain hole on the left

heating element and probe of the PID

aeration wand and bag

 

[Brewmoor]

Here is my new rig. I might have gone a bit overboard

 

[Julohan]

Here is my new rig. I might have gone a bit overboard

:rockin:

 

[hadabar]

back to basics...

 

[heckels]

$42 for shelving brackets, wood sealer and casters.

 

[NattyBrew]

I am super proud that I can finally share my rig with everyone.

Here's my version of a Kal clone. Meet "The Flux Incapacitor"!

 

[Ohio-Ed]

Here is my new rig. I might have gone a bit overboard

Isn't this about the entry point for most first time extract brewers?

Outstanding!! Looks like you are living the dream.

Ed

 

[FSR402]

That's my circulated BIAB Brewery.

Based one 10 gallon electric Urn, 3000W heating power, march pump at the bottom.

Wow I'm impressed. Not sure if I'm more impressed but the cool kettle/tun combo or the fact that you were able to take the most simple way to brew and make it complex. :rockin:

 

[cheese]

Wow I'm impressed. Not sure if I'm more impressed but the cool kettle/tun combo or the fact that you were able to take the most simple way to brew and make it complex. :rockin:

For me, that's what this forum is all about.

 

[chezhed]

For those that want to build but don't want to weld and want to keep it light, try checking out material from 80/20 Inc http://www.8020.net/. I use this stuff and it's great. It's extremely similar to the material Blichmann uses to make the Top Tier, but it's aluminum instead. Can't advise cost though...I get my material from discarded stuff at work I'm building a gravity stand with it now and will post when finished.

 

[benbradford]

I went with wood, and it breaks down for storage, as I have no garage or basement...

 

[mwhc22]

oh man reading all these brew rig/ 1-3 bbl brew set up threads has me wishing i didn't live in a highrise condo.

me thinks im just going to have to get some friend with a house addicted to brewing and brew there instead

 

[benbradford]

mine fits into the "closet", and plugs into the wall, running off of the kitchen sink in a 1000 sq foot apartment...it is possible

 

[bumstigedy]

These are all nice. I need to build something better than what I currently have which is two banjo burners on concrete blocks.

 

[damnitbeavis]

got it used. the kettles aren't in proper order. For 30 gallon batches.

 

[oregonparamedic]

The stand is slowly getting there. Base paint is done. Next up is the finish work and then on to the burners and manifold.

 

[chezhed]

Not finished but it's getting there. Plan to replace shelf brackets with more t-slot stock and add some more

[/url][/IMG]

[/url][/IMG]

 

[bwiens]

Heres mine:


Link: 4 Vessel Brew Stand

 

[chapa]

Heres mine:
http://www.flickr.com/photos/benwiens/5774879554/
http://www.flickr.com/photos/benwiens/5774929064/
Link: 4 Vessel Brew Stand

Awesome rig!

 

[jsguitar]

The patio furniture brewer. I break out the big umbrella on rainy days.

 

[bwiens]

Awesome rig!

Thanks, took some time to get it to where it is. Still needs some work, but these things are never 'finished'.

 

[dfess1]

Here is my single tier sculpture:

 

[JimmyD]

Rig looks good. Are the HLT and Brew kettle from Brewhemoth? I just ordered them, curious if there were any issues?

 

[dfess1]

they are from brewhemoth. my biggest problem is they are not round. trying to find lids are pretty damn hard. And the bottom is not 100% flat either. We had to bend the the stainless grates down a bit, so that the pot would not rock.

 

[PGHBrew]

Just got my stainless stand done a couple weeks ago. I've ran it once so far, hope I can fire it up again this weekend.

 

[wuertele]

That is a sweet looking construction. How did you make the burner supports / kettle supports?

 

[ToastedPenguin]

Here is mine: http://homebrewery.shutterfly.com/

Just need to add my water filter and the gas jumper from the plumbing to the burners.

 

[Strongbad52]

Finally get to add to this thread - got 2 batches in this weekend to break it in.