Merlin-CO
Active Member
[LONG POST...if you're willing to read!]
You guys are all bad influences! All these great DIY builds of all kinds of stuff that I've been following the last year or so drove me to desperation and I had to go and build a bar in my basement. Shame on you!![Mug :mug: :mug:](https://cdn.homebrewtalk.com/smilies/sdrinking-100-154.gif)
So now I'm sure you'll want to see the 'porn' shots of how it all went together - but I don't have a ton. I didn't think to grab the camera until 2/3 through the project. But I do have some shots of what kind of setup I did put together. Hopefully I can inspire a few others of you out there!
What I started with was a 'blank canvas' corner. Luckily for me (or possibly divine intervention) the space behind the wall is where the utility room was (the basement was already finished when I bought the place). And low & behold it was perfectly sized for my keezer!
Moving this back into the utility area allowed me to start doing some serious re-tuning of how I had my keezer setup. The biggest item was clearing the space taken up by the CO2 tank and moving it out. In this shot below you'll see that I'm running a two-regulator system with one going into a 3-way distribution panel. The other is free right now to pressurize kegs outside of the keezer for initial shake-priming.
Eventually I'll upgrade the 3-way to a larger panel to accommodate more kegs on two different pressures (so I can have a higher pressure group for Wheats/Wiezen's) as well as get a Nitro system setup - but that's later. You'll see that I have each tagged with a letter and color...
...and these match up with the appropriate CO2 supply line that has a zip-tie ID tag on each...
Inside the keezer I'll eventually be able to run 6-kegs with a 7th for a glycol-like system supply I'm running (with just water at the moment). I just finished installing the fan into the top today, and boy what a difference it makes in maintaining temp!
Right now the water/glycol system is just sitting in a bucket with a good pond pump I picked up at my local Lowes. The 'In' & 'Out' lines run in a group with 3 beer lines that I wrapped together from scratch.
The 'In' & 'Out' lines run in a group with 3 beer lines that I wrapped together from scratch in this configuration (below). I used a plastic wrap to keep them together and then wrapped that in a layer of aluminum ducting tape and then wrapped that in a foam-rubber self-sealing pipe insulation section.
Right now I'm also running a Tee off of the glycol lines and that runs out of the keezer into a water bucket with some copper tubing in the water that helps to keep my currently fermenting Hefe at a decent temp (it's pretty warm here in Colorado, even in my basement).
[CONT'D]
You guys are all bad influences! All these great DIY builds of all kinds of stuff that I've been following the last year or so drove me to desperation and I had to go and build a bar in my basement. Shame on you!
![Mug :mug: :mug:](https://cdn.homebrewtalk.com/smilies/sdrinking-100-154.gif)
![IMG_0692.jpg](https://proxy.imagearchive.com/0ee/0ee300855b34a612897b9590025874b6.jpg)
So now I'm sure you'll want to see the 'porn' shots of how it all went together - but I don't have a ton. I didn't think to grab the camera until 2/3 through the project. But I do have some shots of what kind of setup I did put together. Hopefully I can inspire a few others of you out there!
What I started with was a 'blank canvas' corner. Luckily for me (or possibly divine intervention) the space behind the wall is where the utility room was (the basement was already finished when I bought the place). And low & behold it was perfectly sized for my keezer!
![IMG_0682.jpg](https://proxy.imagearchive.com/53e/53e5839b873f204ea2075d0f4eee08db.jpg)
Moving this back into the utility area allowed me to start doing some serious re-tuning of how I had my keezer setup. The biggest item was clearing the space taken up by the CO2 tank and moving it out. In this shot below you'll see that I'm running a two-regulator system with one going into a 3-way distribution panel. The other is free right now to pressurize kegs outside of the keezer for initial shake-priming.
![IMG_0683.jpg](https://proxy.imagearchive.com/e20/e207bd4fd204ecf414b162b5757c7ea1.jpg)
Eventually I'll upgrade the 3-way to a larger panel to accommodate more kegs on two different pressures (so I can have a higher pressure group for Wheats/Wiezen's) as well as get a Nitro system setup - but that's later. You'll see that I have each tagged with a letter and color...
![IMG_0693.jpg](https://proxy.imagearchive.com/dc1/dc16ce5f812e0cd51e0f8cf6c76a40a4.jpg)
...and these match up with the appropriate CO2 supply line that has a zip-tie ID tag on each...
![IMG_0694.jpg](https://proxy.imagearchive.com/d45/d45aa6e780268316cdad79ed28455215.jpg)
Inside the keezer I'll eventually be able to run 6-kegs with a 7th for a glycol-like system supply I'm running (with just water at the moment). I just finished installing the fan into the top today, and boy what a difference it makes in maintaining temp!
![IMG_0691.jpg](https://proxy.imagearchive.com/659/6599d5850421b2dcce062536d8f5c045.jpg)
Right now the water/glycol system is just sitting in a bucket with a good pond pump I picked up at my local Lowes. The 'In' & 'Out' lines run in a group with 3 beer lines that I wrapped together from scratch.
![IMG_0686.jpg](https://proxy.imagearchive.com/338/33895990be0c80078e33d68277c3578a.jpg)
The 'In' & 'Out' lines run in a group with 3 beer lines that I wrapped together from scratch in this configuration (below). I used a plastic wrap to keep them together and then wrapped that in a layer of aluminum ducting tape and then wrapped that in a foam-rubber self-sealing pipe insulation section.
![IMG_0075.jpg](https://proxy.imagearchive.com/31e/31e393c1beec717703dbcd153520e77c.jpg)
Right now I'm also running a Tee off of the glycol lines and that runs out of the keezer into a water bucket with some copper tubing in the water that helps to keep my currently fermenting Hefe at a decent temp (it's pretty warm here in Colorado, even in my basement).
![IMG_0078.jpg](https://proxy.imagearchive.com/ddd/dddb66ef94e2584366d80cae4f5351b6.jpg)
[CONT'D]