• Please visit and share your knowledge at our sister communities:
  • If you have not, please join our official Homebrewing Facebook Group!

    Homebrewing Facebook Group

Going all-grain on a budget.

Homebrew Talk

Help Support Homebrew Talk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
I did the 5 gallon rubbermaid cooler $18 canadian and with the fittings and washers about $50. Picked up a turkey fryer from crappy tire for $89.99 came with 9 gallon aluminim pot and propane burner and stand. Analogue thermometer to 220f $10

$150,to switch to AG and its all u really need. I can upgrade to a ss pot anytime and use the one i have as a hlt or a turkey fryer.
 
Wo-hoo! someone that actually LIKES a Corona mill. I was going to get one but was put off by all the comments that one must get a roller mill because a Corona is no good.

I am using a corona style mill. I am satisfied with the results. I am not getting consistent efficiency but I think the problem is elsewhere. There are a lot of people that have used a corona mill for the entire time with good results.
 
Wo-hoo! someone that actually LIKES a Corona mill. I was going to get one but was put off by all the comments that one must get a roller mill because a Corona is no good.

You need to see Revvys post about his. Lots of info about them there and making adjustments etc. It just takes practice and adjustments to know what youre getting as your final product. If I remember right it was Yooper that gave it to him. Its a nice long thread full of cool set ups.
 
I have a propane burner that I use for fish frying. 5 gallon batches for now. I'm wanting to start kegging too so I want to spread my budget out as much as possible.
 
Advice from owning a 5 gallon rubbermaid cooler. I regret not getting a 10 gallon. Many beers require 2 sparges if you batch sparge like i do. So it uses more time
 
I use to pots on the stove for my all grains and it works fine. I have I big stainless steel pot and it is still in the box. None of them have valves.
 
If you are really on a low budget go for small batches like I do. Lets you have many different beers on hand to drink as you feel fit for that day. Can't get much lower on budget than this for all grain.

 
Last edited by a moderator:
I bought a propane burner and 7.5g pot combo at Walmart for 50$ and grabbed a mesh bag from the brew shop and did biab with that setup. It worked great for 60$. Since then I've upgraded to a cooler mashtun which I'll say was definitely worth it. I use an ale pale to hold my first runnings while I sparge
 
Here is the brew kettle I just received:

http://www.ebay.com/itm/130722410669


$120 for a 32 Qt SS pot with SS valve and thermometer. It isn't as heavy as my normal 14 Qt stock pot, but it holds water just fine. As long as you don't run it dry, this shouldn't be a problem. The cool thing about it is it is inductive capable, even though it does not list it. I tried it out on my inductive cooktop


MLT consists of a $45 10 Gal Rubbermaid Cooler, a $3 3/8 in nipple, a $3 3/8 FIP/Barb fitting a $8 3/8 in ball valve, a $3 3/8 MIP/barb fitting, $3 worth of washers and a SS Screen scavenged from a SS sink hose (I already had it, so no cost. To buy one you'd be out about $5) All told, about $65 for a 10 Gal MLT....about half what you'd spend at a LHBS. You could roughly double the fitting cost to move to SS if desired, you'll still do better than a LHBS.


And honestly, if you have a kettle large enough for full extract boils, and a second pot for sparge water that is at least half the size of the boil kettle/batch size, all you really need to get into all grain is a large nylon bag and a strainer basket that will fit over your kettle. Not the easiest way to get it done, but it would allow you to get your feet wet before getting more gear. I didn't think $65 was too much to get into all grain.
 
Well, I came up with a ten gallon aluminum kettle for $30. And dropped about $25 on the mash tun. Hit up the home brew shop over the weekend and picked up the ingredients for a wheat ipa. Brew day next Sunday. Thanks for all your help.
 
In order to give you the best possible answer, we must know your age.

@ 30 years old I purchased a plain ole SS kettle without all the bells or whistles. Another 10 years and a drain valve would be a necessity.

I just started feeling REALLY old for some reason. Guess I should start thinking about making my setup ADA approved...........:mug:
 
If you want to brew on a budget get a alum pot, I got a 8 gal for $29 shipped, amazon, still have the link if you want. Plus a cooler 10gal with a mesh braid for $60 topps.. thats it... thats what I have, I fly sparge with a strainer and a pitcher and I get about 78% efficiency. Im happy....
 
Nice. I just finished my brew day. Finally knotched my stirring spoon at 1 gallon increments this time. Made things go alot smoother. Now the next step in the budget all grain setup for me is a ball valve on the kettle and a refractometer so i can tell if i need to boil off extra wort or add dme. Still pretty new at this. Good luck tomorrow and most importantly. Enjoy the process
 
Finally mashed in. I'm worried about not holding temp. I've got the cooler sealed up and covered in blankets. Should I rdwhahb, or open it up and check temp in a bit?
 
Mutt98 said:
I resisted and lost less than a degree. Finish my sparge now. Forgot my flaked wheat then threw it in before the sparge. Currently winging it:)

Good job on temps. Last weekend I forgot my whirlfloc and yeast nutrient, and forgot to take final grav...fixed the last by opening up and getting a sample after pitching.

Today I got early start and brewed 2 batches, yeast pitched and into the chamber before cracking a homebrew.... Thinking RDWHAHB is for after the brew day when you are thinking back on what you might have done better...not for when you imagine everything is going swell during the brew day...
 
Well, it's in the fermentor. Og was almost perfect. So that's good. I think I lost 3/4 of a gallon while trying to get wort into carboy. I think a kettle valve would be a good investment. That recipe had about 5 oz of hops in it. Do you typically strain all those hops?
 
When I use the carboy, I either dump most of the hops in or pour through a big SS strainer. It usually clogs up the strainer pretty fast though so it takes a while. Depends on my mood and how many extra hands I have around.
 
Instead of putting the hops directly into the kettle, you can use a 5gal paint strainer. They only cost a couple bucks at Home Depot or Lowes, and seemingly last forever if you don't mind cleaning them out afterwards. I use a metal spring clamp to hold it to the side of the kettle and a handful of Dollar General glass marbles to keep it weighted down. Before transferring, simply lift the whole bag out.... Plenty of high tech ways of doing the same (look up hop spider), but I've never seen a reason to go any other way. Simple, cheap, and it works. I also rack through a second strainer (they come 2 to a pack :)) into bucket or carboy to pick up remaining debris, and it also helps to begin adding oxygen as well.
 
Mutt98 said:
Well, it's in the fermentor. Og was almost perfect. So that's good. I think I lost 3/4 of a gallon while trying to get wort into carboy. I think a kettle valve would be a good investment. That recipe had about 5 oz of hops in it. Do you typically strain all those hops?

I strain with this.
10 inch conical fine mesh strainer. Pulls out hop pellet residue and most of the trub. Aerates the wort. I do have a valve on my kettle that makes it easy unless I use whole hops. Then I have to siphon.

image-3180241386.jpg
 
I just started feeling REALLY old for some reason. Guess I should start thinking about making my setup ADA approved...........:mug:

I don't have a valve on my kettle (yet) but will soon install one. Even my soon-t-be 31 year old back is screaming at me the morning after brewing a batch.

Thanks dad for the genetic predisposition....
 
I found a used restaurant supply store that was selling items on consignment. I got a 40qt aluminum stock pot that is very thick walled for $25. I agree that a Corona mill, if dialed in right, does a fine job crushing grains.
 
Back
Top