Do you need a 1 off Stainless part built for your system? Let's discuss it.

[Jaybird]

Maybe this already exists and I just can't find it, but I need a 2" tri clamp ferrule that has a flange on the other end which I can drill holes through in order to bolt it to a 3/16" thick stainless tri-ply lid. In other words, a bulkhead flange.

EDIT: Actually, I could just use one of the end flanges from a 2" sight glass.

View attachment 598071

Hey JayJay I don't have any of the end flanges by themselves. If you want to do a quick "hand CAD" drawing and send it my way I can take a look at exactly what you are wanting.

Cheers
Jay

 

[NewJersey]

A false bottom that works with the new ss brewtech 10gallon 1V ebrewing setup. Would love an easy way to remove it after the mash as well.
A whirlpool arm that would fit in the same kettle's unused 1.5" tc port.
I ordered a few days ago and haven't even brewed with it yet, but that's what i think I'll need to get going with a bag from wilser.

 

[NewJersey]

still need this

 

[HOPtuary]

Hehe I did notice. Thank you very much!

I’m way beyond impressed. I’ll have to write up my experience next brew day.

View attachment 592134

Where did you get this sparge arm from?

 

[PeteSeattle]

Where did you get this sparge arm from?

Hi @wanger99

Jay fabricated it in his shop (@Jaybird). Message him here or pm him and he will certainly get back to you. Cheers.

 

[Stealthcruiser]

A false bottom that works with the new ss brewtech 10gallon 1V ebrewing setup. Would love an easy way to remove it after the mash as well.
A whirlpool arm that would fit in the same kettle's unused 1.5" tc port.
I ordered a few days ago and haven't even brewed with it yet, but that's what i think I'll need to get going with a bag from wilser.

@Jaybird

 

[Jaybird]

Sorry for the late replies guys.

@NewJersey
Shoot me a PM with what you are wanting with sizes and specs and I will dive into it for you.

@wanger99
I got your PM I will reply shortly.

Cheers
Jay

 

[hezagenius]

Hey @Jaybird . Got a new kegmenter with a 4" TC opening and would like to get a TC cap lid with the following:
One 1.5" TC ferrule to add dry hops so I don't have to undo the whole lid
One thermowell (maybe 12" ?)
One or two threaded ball lock posts (19/32" - 18)

I've seen a 4" x 1.5" TC cap reducer at brewers hardware and that is probably a good base piece to add the thermowell and ball lock post(s) to.
Brew hardware sells the threaded ball lock posts designed for welding

 

[Jaybird]

Hey @Jaybird . Got a new kegmenter with a 4" TC opening and would like to get a TC cap lid with the following:
One 1.5" TC ferrule to add dry hops so I don't have to undo the whole lid
One thermowell (maybe 12" ?)
One or two threaded ball lock posts (19/32" - 18)

I've seen a 4" x 1.5" TC cap reducer at brewers hardware and that is probably a good base piece to add the thermowell and ball lock post(s) to.
Brew hardware sells the threaded ball lock posts designed for welding

View attachment 600825

View attachment 600826

I have everything in stock here to be able to build that out. I am curious if the 2 ball lock posts will work when you account for the connector that needs to attach to that. Let me get to the Fab Shop and just lay it out for you. I'll shoot you a PM tomorrow if I cant get back here to the store today.

Cheers
Jay

 

[SandstoneCityBrew]

Jay, do you offer something like this?

https://www.morebeer.com/products/trub-trapper.html

 

[Chad_C]

Jay, I may need one of these sparge arms as well, but without the bend in the arm. I have a bulkhead for a cooler lid, but need to have the arm “hang” from the center of the lid. 1/2” diam.

 

[Tobor_8thMan]

Jay,
I need 2 slotted (or other recommendation) 304 or 316 stainless pieces for my condensate hood. Need these to catch the moisture and direct the liquid to the hood gutter. Need 2 pieces each 26 inches long x 16 inches high. Available?

 

[Rodent]

Hi @Jaybird - top of the New Year to ya!

I'm in need of 2ea 1.5" x 1.375" long TC spools; tube ID needs to be 1.304" or larger

Sadly for my use case, a standard 1" long spool is .25" too short, and a 2" spool is too long for a fitting to fit thru and into my conical.

Is something like this doable? Cost?

 

[Jaybird]

Jay, do you offer something like this?

https://www.morebeer.com/products/trub-trapper.html

A round disc of perf 9" in diameter and 2.75" tall? Sure.
Its not going to have the rubber gasket around the top and bottom but yeah. I can roll that ring.

Shoot me a PM.

Cheers
Jay

 

[Jaybird]

Jay, I may need one of these sparge arms as well, but without the bend in the arm. I have a bulkhead for a cooler lid, but need to have the arm “hang” from the center of the lid. 1/2” diam.

Shoot me a PM and lets discuss your project in detail.

Cheers
Jay

 

[Jaybird]

Ar

Jay,
I need 2 slotted (or other recommendation) 304 or 316 stainless pieces for my condensate hood. Need these to catch the moisture and direct the liquid to the hood gutter. Need 2 pieces each 26 inches long x 16 inches high. Available?

Are you talking FLAT or round?

Shoot me a PM with a little hand sketch and lets check it out.

Cheers
Jay

 

[Jaybird]

Hi @Jaybird - top of the New Year to ya!

I'm in need of 2ea 1.5" x 1.375" long TC spools; tube ID needs to be 1.304" or larger

Sadly for my use case, a standard 1" long spool is .25" too short, and a 2" spool is too long for a fitting to fit thru and into my conical.

Is something like this doable? Cost?

Absolutely. What is your +- tolerance in the length?

Cheers
Jay

 

[Jaybird]

Hi @Jaybird - top of the New Year to ya!

I'm in need of 2ea 1.5" x 1.375" long TC spools; tube ID needs to be 1.304" or larger

Sadly for my use case, a standard 1" long spool is .25" too short, and a 2" spool is too long for a fitting to fit thru and into my conical.

Is something like this doable? Cost?

https://www.norcalbrewingsolutions.com/store/Custom-1.5-Inch-Tri-Clover-Extension-Tube.html

Here is a link to that part and its cost.

Cheers
Jay

 

[Copbrew133]

Hey Jay,

Any chance of making this out of stainless?

 

[Jaybird]

Hey Jay,

Any chance of making this out of stainless?View attachment 607621

Man if I thought I could sell a boatload of them I would totally dive into that. If you want just 1 and want me to ask my CNC guy what it would cost to make it I am happy to do that. That said I can assure you its well into the $150+ range for a 1 off for that. TOTALLY DOABLE though.

Cheers
Jay

 

[Jaybird]

Now that said I do make one "sort of" that you can use in its place. Give me a few min I'll post up a pict if I can.

Cheers
Jay

 

[Jaybird]

Like this. We have been selling them in store for $29.99

Cheers
Jay

 

[Konadog]

Like this. We have been selling them in store for $29.99

Cheers
Jay

I'm probably blind, but do you have a link? I can' find them.

 

[AF1HomeBrew]

Like this. We have been selling them in store for $29.99

Cheers
Jay

I'd be interested in one of these also, but couldn't find it on your site.

 

[AF1HomeBrew]

Like this. We have been selling them in store for $29.99

Cheers
Jay

Wonder if it could be modified so that Stainless Steel Floats could be attached, so that it would float in the mashtun.

 

[Jaybird]

I'm probably blind, but do you have a link? I can' find them.

Sorry you guys. It's a part we have been selling in the actual walk in store..LOL My web guy has not had a chance to add them to the web store. Go figure! If you want one just shoot me a PM I'll take care of you.

Jay

 

[Jaybird]

I'd be interested in one of these also, but couldn't find it on your site.

I just replied to @Konadog but yeah we haven't had a chance to get them on the website. If you want one just shoot me a PM I'll take care of you.

Cheers
Jay

 

[Konadog]

If you want one just shoot me a PM I'll take care of you.

Cheers
Jay

PM inbound!

 

[microbusbrewery]

Like this. We have been selling them in store for $29.99

Cheers
Jay

What's the tubing size on this? Also, what's the size of the gap between the plates? I use a siphon sprayer to recirculate on my HERMS system, so I need the gap at least big enough so that any husks that get past the FB won't clog the sprayer.

 

[Jaybird]

What's the tubing size on this? Also, what's the size of the gap between the plates? I use a siphon sprayer to recirculate on my HERMS system, so I need the gap at least big enough so that any husks that get past the FB won't clog the sprayer.

Gap is right at 1/4" so that shouldn't be a problem. Tubing is our 1/2" .035

Cheers
Jay