Weldless Triclover Element?

[emjay]

You know if you'll be going ahead with an OD threaded version?

 

[Bobby_M]

You know if you'll be going ahead with an OD threaded version?

Nothing in the works at the moment. One of the downsides to that solution is just how big of a hole you would need to make. If you're willing to make a weldless system, that large, maybe the way to go about it is just make the 1.25" hole and use a 1" NPS locknut. We have a new enclosure that will work with that.

 

[Bobby_M]

 

[kopper]

Bobby, will the solder on tri-clover flange only be available in 1.5"?

 

[Bobby_M]

Bobby, will the solder on tri-clover flange only be available in 1.5"?

Correct, at least for now. I know there are some 2" adapters out there, but I'd assume that people who went that route already already had the ferrule solution sorted out. I don't know, let me know why you would want a 2" version.

FYI, for anyone playing along, the 1.5" TC version is large enough for every element that I've tested fit on, even the ripples.

 

[Flomaster]

I jut got the biggest hard on watching this Soldered Tri-Clover flange setup.

-=Jason=-

 

[Bobby_M]

I jut got the biggest hard on watching this Soldered Tri-Clover flange setup.

-=Jason=-

Thanks. I think.

 

[sologman]

Bobby,
In the video you show an economy "miniature element enclosure" that screws onto the pot using a lock nut and tephlon tape (at about 5 minutes). I may be jumping the gun, but is this element enclosure available on your website? I only see the enclosure with TC Clamp.

Thanks!

 

[Flomaster]

so my next BH order will be as follows

False Bottom
5/8" dip tube
2- solder Tri-Clover adapters
1- Tri clover elment housing
1- solder kit... I used the last bit of my flux and solder with my MLT keggle.

im gonna have to sweet talk the wife into letting me drop some coin on this.

-=Jason=-

 

[Bobby_M]

Bobby,
In the video you show an economy "miniature element enclosure" that screws onto the pot using a lock nut and tephlon tape (at about 5 minutes). I may be jumping the gun, but is this element enclosure available on your website? I only see the enclosure with TC Clamp.

Thanks!

I jumped the gun posting the video. I do have them here but I just got the large cord grips in like 10 minutes ago so I need to take pics, figure out the pricing and then get them on the site. Look for it by Sunday.

Bobby

 

[OMJ]

anyone else thinking this at the moment?

 

[Weezy]

See any problems with fitment with this on ~8-9 gallon tanks at 12.5"-12.75" diameter? I'm ready to order too....just not sure how many and if it'll fit.

and +1 on the solder kit!

 

[Bobby_M]

Ok, solder kits in the works.

I'm still trying get a handle on which pot diameters will work. Of course, any radius is better than none. The flange has a 8" radius so when it's fit to a 13" diameter pot, the side gaps are less than 1/16". When you clamp it together and solder, it will hold no problem. I think 12" Diameter would be my limit on the low end and probably 20"D on the high end. I suppose you could make some mild modification to the radius on the flange with a grinding wheel if you're careful. It's probably not necessary because the kettle walls are plently flexible and they will clamp to the flange with no problem. The solder will hold it all together.

 

[MX1]

Ok, Bobby

You have just made this Soldier very happy.
Just make sure you have the weldless versions in stock in November, when I get back from this crappy sand box!

Awesome job giving us just what we wanted and asked for, your sir are my hero!

Tim

 

[Peter_h]

Are you going to be stocking the 1.5" triclover caps mentioned in the video? I don't see them on your site.

 

[Bobby_M]

Yes, I'm working on adding the buttons to the site right now..

 

[Flomaster]

I get paid tomorrow, I was looking to buy 1 Tri-Clover, 1 False Bottom, and 1 Dip tube. do you think I'll be able to order through the website?

-=Jason=-

 

[Bobby_M]

Yes, The page is live with the enclosures. There are full descriptions and cart buttons there but not the current pictures. I'm working on those now.

 

[huntb]

Bobby, have you decided if you are going to start selling solder kits yet?

 

[Bobby_M]

Ok, I finally got all the pictures taken care of and figured out all the different configurations that are practical to offer. Of course I welcome and appreciate any feedback you guys and gals may have. The Harris soldering kits are on order and should be here early next week.

Here's what the solder-on assembly looks like all put together with a sample element installed. Of course, you'll get a lot more out of it once I finally get around to soldering one on in a video.


http://www.brewhardware.com/rimsherms-parts-93

 

[jeffmeh]

Bobby, this is great!

 

[vinylicious]

Bobby,

How large of a hole will the solder flange accommodate? I have a 1-5/8" punch that I used to attached one of your welding spuds in a difference pot. Would this size work for the solder flange?

 

[Bobby_M]

The ID of the flange is 1-3/8 and the OD is 2". If you center the flange over a 1-5/8" hole, you'll have a contact ring 3/16" all around. It's a little less than ideal, but that's still more contact area than a pulled dimple and regular ferrule. I think it will be OK, extra bonus for feeding a little solder in from the interior of the pot.

 

[OMJ]

Ok, I finally got all the pictures taken care of and figured out all the different configurations that are practical to offer. Of course I welcome and appreciate any feedback you guys and gals may have. The Harris soldering kits are on order and should be here early next week.

Here's what the solder-on assembly looks like all put together with a sample element installed. Of course, you'll get a lot more out of it once I finally get around to soldering one on in a video.


http://www.brewhardware.com/rimsherms-parts-93

Bobby you should add an option to purchase extra TC gaskets. I know I would have added a couple on my order had the option been there.

 

[LandoLincoln]

That's pretty awesome! Now to get one with a Neutrik Powercon 32a quick disconnect on the end...

 

[Bobby_M]

On paper, the NAC3MP-HC will fit. I just need to get one to see if it's practical given 10g wire between the connector and element in a relatively small space.

 

[Weezy]

This is just awesome, Bobby. What a selection! I'll be ordering 3 setups (plus $100 of misc. hardware for a whole new two-pot setup).

 

[MX1]

Bobby,

Just checked out the new site,and the weldless option for the element enclosure, OUTSTANDING!

I will be ordering sometime after I redeploy, cant wait, this will help keep the new pilot system looking sharp!

And I hope the Switchcraft Male Panel mount connectors will work in the end, if not I will just make a short Pigtail...

Thanks again

Tim

 

[Docbruw]

I have to agree with everyone else. Very nice setup at a great price. Can't wait to order some from you when I get to that point in my brewery conversion.

I'm not sure if anyone else would like this but a right angle cord grip would make power cable management a lot easier. Any chance of getting that option?

 

[Bobby_M]

I have a few of the larger grips with the same stain relief found on my RIMS tubes and I suppose that would be the best way to have 10/3 SJ make a turn like that.