Two Tier Brew Rig Build!

[InfernoBrews]

Ok I been posting under "Wood Frame Brutus RIMS Project" Thread.. But Decided to Just start a New on for this.. I Have worked on this Stand tor two evenings and one day now and this is where i am.. Feel Free to shoot questions and or Likes Dislikes I am always open for other views on things!

Day 1.....

 

[InfernoBrews]

Day 2......

 

[InfernoBrews]

Day 3....
Assembled Gas lines, Burners And test Fired.......Test Positive!
And a Pic to Get the Feel on how its going to Look...

 

[JOHN51277]

Looks like a fire hazard to me. I think those side boards might get a lil toasty!

 

[InfernoBrews]

Have Heat Shields That have not been Installed Yet..

 

[dannedry]

How do you feel that the gas pipe hold up to the flame?

 

[rhutter]

since your burners are in the middle of the frame and not off-centered maybe something like these will be good - https://www.homebrewtalk.com/f51/heat-shields-necessary-162611/index2.html Check about 2/3s down the page.

Not sure if you made something similar or went with sheet metal cut and rounded. Post some pics of the shields when you can, I would like to see how you approached them.

Rob

 

[NinjaJoe]

since your burners are in the middle of the frame and not off-centered maybe something like these will be good - https://www.homebrewtalk.com/f51/heat-shields-necessary-162611/index2.html Check about 2/3s down the page.

Not sure if you made something similar or went with sheet metal cut and rounded. Post some pics of the shields when you can, I would like to see how you approached them.

Rob

Direct link

 

[InfernoBrews]

How do you feel that the gas pipe hold up to the flame?

It should be just fine. I am painting it with high temp paint which will probly only last a bit before signs of ware from the heat show.

 

[bja]

It should be just fine. I am painting it with high temp paint which will probly only last a bit before signs of ware from the heat show.

I would be concerned that they may start to sag when they get hot and with full pots on them.

 

[android]

looks good, i think you'll have plenty of support and not much in the way of fire danger if you put some sort of protection on. nice work!

 

[InfernoBrews]

I will try and get some more pics up later today sometime.

 

[InfernoBrews]

oK Here is another pic of it with one coat of paint.. As some other have done i used High Heat Paint in the inside of the Frame..

As for those of you wanting to see the heat shields pics of that will be coming soon..

 

[diatonic]

I hope your username doesn't become ironic after your first brew!

 

[BrewFiend]

Nice work man, quality assembly! I don't think you're gonna run into a lot of heat problems with a heat shield on there and it running outside.

 

[BrewFiend]

I would be concerned that they may start to sag when they get hot and with full pots on them.

Those are 4x4 pressure treated posts and 2x8 framing all lag bolted together. It would hold 4x that weight and not sag...

 

[doctorRobert]

Those are 4x4 pressure treated posts and 2x8 framing all lag bolted together. It would hold 4x that weight and not sag...

yeah i was about to that looked a little overkill... but cool none the less

 

[BrewFiend]

Yeah maybe but if its built way overspeced it will last can't compete, with sheer mass!

 

[diatonic]

I agree that the stand will be strong... But wood + propane burners = bad idea to me. You know what campfires are made of? Wood. Know how many commecial wood burner stands are on the market? Zero. Can you get away with it? Maybe. Is it worth the risk? Not to me.

 

[bmckee56]

Can you post a material list and cost for your 2 tier setup. I am considering one myself, but it was going to be a 3 tier. I may however make it 2 and just place my burner assembly on the ground next to the rig. I am going to use an electric heating element to heat my top tier water for my mash. Not at the automated stage yet.

Your set-up looks great. Good luck on your first brew with it.

Salute!

 

[InfernoBrews]

yeah i was about to that looked a little overkill... but cool none the less

Go Big Or Go Home.. That was my Theory!

4x4 and 2x6 with 4" Casters..

 

[InfernoBrews]

Can you post a material list and cost for your 2 tier setup. I am considering one myself, but it was going to be a 3 tier. I may however make it 2 and just place my burner assembly on the ground next to the rig. I am going to use an electric heating element to heat my top tier water for my mash. Not at the automated stage yet.

Your set-up looks great. Good luck on your first brew with it.

Salute!

Sure thing ill get it together.. I Bought a lot of items and then came up with better ideas so i have to Return a bunch of things and sort out the pricing for everything.. but i will get it up ASAP..

 

[bja]

Those are 4x4 pressure treated posts and 2x8 framing all lag bolted together. It would hold 4x that weight and not sag...

I was talking about the pipes supporting the burners. I'm assuming the pots will sit on them.

 

[jspence1]

Steel shouldn't start to soften until it reaches 400C, it it gets that hot he's going to have bigger problems than that most notably the flaming rig

Looks like an amazing build! Every time some builds a rig out of wood the fire marshal Bill comes out. Let me tell you somethin I haven't heard of one bursting into flames yet

 

[diatonic]

"Let me tell you somethin'..."

 

[rhutter]

Looking good - hey, what model burners did you go with?

 

[InfernoBrews]

High Pressure Burner..

 

[GNBrews]

Inferno,

can you take a photo of the area where the burners are attached to the stand? Looking awesome, BTW.

 

[InfernoBrews]

Inferno,

can you take a photo of the area where the burners are attached to the stand? Looking awesome, BTW.

Yep sure will.. been so busy with work i haven't had time to get a few new pics taken.. So i plan on working on trying to finish up some last min things on it today so i can Test everything tomorrow.. So pics will be coming..


O and for those talking about the heat shield early on in the thread.. Ill get pics too.. i came up with other ideas for them so been playing with those ideas and should have them being installed today as well..

 

[ezerhoden]

Hey, looks really good. Where in Pittsburgh? I live in Moon Twp and would love to come by to check it out sometime.

Bob