ANVIL FOUNDRY ALL-GRAIN BREWING SYSTEM

[tracer bullet]

I'd also try contacting Anvil / Blichmann. It would seem their days of being slammed are somewhat over and they are responsive again. It seems historically they've always done the right thing but for a while it was pretty slow. You may get advice or even parts from them, perhaps even free parts.

 

[IslandLizard]

I guess I just order new fan and switch

Error Code 01 points to an open circuit.
Did you watch the video?

Do the fan and switch seem to be the problem?

 

[DarrellQ]

I'd also try contacting Anvil / Blichmann. It would seem their days of being slammed are somewhat over and they are responsive again. It seems historically they've always done the right thing but for a while it was pretty slow. You may get advice or even parts from them, perhaps even free parts.

Good info, thanks!

 

[DarrellQ]

Error Code 01 points to an open circuit.
Did you watch the video?

Do the fan and switch seem to be the problem?

So I removed the fan and applied 12 volts to it from a 12 volt power supply (I realize the fan is 18 volts) and it worked fine. I removed the reset switch and I don't know how much travel is expected from the button? It doesn't go in very far at all. Maybe it only pops out upon heat default, dunno.

 

[IslandLizard]

So I removed the fan and applied 12 volts to it from a 12 volt power supply (I realize the fan is 18 volts) and it worked fine. I removed the reset switch and I don't know how much travel is expected from the button? It doesn't go in very far at all. Maybe it only pops out upon heat default, dunno.

It could well be a spring activated switch-off due to overload, too high a current or too high a temperature.
Pressing it may (should?) reset it, yes. Have you tried that?

If that doesn't fix it, I'd contact Anvil/Blichmann, as @tracer bullet already suggested. Don't start ordering parts until you know what the issue is.

 

[DarrellQ]

It could well be a spring activated switch-off due to overload, too high a current or too high a temperature.
Pressing it may (should?) reset it, yes. Have you tried that?

If that doesn't fix it, I'd contact Anvil/Blichmann, as @tracer bullet already suggested. Don't start ordering parts until you know what the issue is.

Yes, I tried that. I removed the long rod and spring that contacts the switch button and removed the switch and tried to just push the button. It doesn't seem to push in more than a couple millimeters. I don't if won't push in because it hasn't popped out or if that is the way it is suppose to act?

 

[Oginme]

Yes, I tried that. I removed the long rod and spring that contacts the switch button and removed the switch and tried to just push the button. It doesn't seem to push in more than a couple millimeters. I don't if won't push in because it hasn't popped out or if that is the way it is suppose to act?

As others have said, contact Anvil/Blichmann. They responded to the couple of issues I have had (1st gen Foundry) very quickly and sent me what was needed to get the machine back up and running, including upgrading the fuse with a breaker at no charge.

 

[Ballaratguy]

I’ve got the Guten (Australian) which I believe is that same as the anvil
I converted mine and bypassed the original controller and connected a Grainfather Control box
Gee that is a game changer for the Guten

 

[tracer bullet]

I’ve got the Guten (Australian) which I believe is that same as the anvil

Hmm, pretty sure it's not the same

 

[Ozarks Mountain Brewery]

have you looked at this pdf, scroll down to the error code under trouble shooting

https://www.docdroid.net/4dtVNLm/the-unofficial-anvil-foundry-bible-11-25-2020-pdf#page=20
TROUBLESHOOTING
E1 Error Code
User reported that they called Anvil Tech Support and they suggested DISCONNECTING
THE POWER then removing the black base of the Anvil and check the connections. There
was a white ribbon cable to the control board that was not firmly set into the socket. A
couple of screws got an extra quarter turn. Put it back together and should heat up
without any error codes.

 

[DarrellQ]

Got this rapid reply from Anvil: "The E1 code is referring to a faulty temperature sensor. Check all wiring to make sure everything is tight, clean and free from debris. If everything looks good then the temperature sensor needs replaced. Foundry™ Temp Sensor

 

[tracer bullet]

Got this rapid reply from Anvil: "The E1 code is referring to a faulty temperature sensor. Check all wiring to make sure everything is tight, clean and free from debris. If everything looks good then the temperature sensor needs replaced. Foundry™ Temp Sensor

If you own a multimeter there's a chance you can check the temp sensor itself. Probe the wires and look for it having a connection, maybe a particular impedance? I don't have the details but am willing to bet you could get an idea if it's working or not before you buy another. Then again... it might just deepen the rabbit hole if you convince yourself it's working but it really isn't.

 

[IslandLizard]

I removed the long rod and spring that contacts the switch button and removed the switch and tried to just push the button.

If you own a multimeter, as @tracer bullet suggested, you can test most components for resistance and continuity, such as that "reset" switch and temp probe. Make sure the unit is switched off and unplugged!
Temp probes are typically (generic) NTC "resistors," changing resistance as a function of the temp.

You can also test/check working voltages when the unit is plugged in and switched on. But beware, you're dealing with 120V or 240V, which are potentially lethal, so know what you're doing, and keep one hand in your pocket.

 

[mantaray]

What process do you follow for disconnecting pump hoses without dumping beer everywhere?

It seems like I cannot help but make a mess in the kitchen.

With the Anvil 6.5 on the counter, last time I did the following:
1. Shutoff Valve
2. Disconnect hose from spigot
3. Drop hose in bucket that is sitting on the floor
4. Let beer drain

Getting all the beer out (especially on the "out" side of the pump) was still a challenge. I still succeeded in making a mess.

Is there a better way? Thank you.

 

[tracer bullet]

You are talking after cool down, headed to the fermenter?

Before I close the shut-off valve at the Anvil, I raise the pump in the air. It has the effect of sort of "draining" much of what is in the pump and lines backwards into the kettle. For me it only takes a few seconds for the level of the wort to flow backwards through the pump itself and into that line, and so at that point the pump and the outlet are "dry". Well they are drained anyhow.

Then I close the valve on the Anvil itself. Then disconnect the pumps inlet line at the pump itself while it is still in the air, pinch it with my fingers a bit, and redirect it to the fermenter. Lastly open the valve again.

Hope that made sense.

 

[Ozarks Mountain Brewery]

What process do you follow for disconnecting pump hoses without dumping beer everywhere?

It seems like I cannot help but make a mess in the kitchen.

With the Anvil 6.5 on the counter, last time I did the following:
1. Shutoff Valve
2. Disconnect hose from spigot
3. Drop hose in bucket that is sitting on the floor
4. Let beer drain

Getting all the beer out (especially on the "out" side of the pump) was still a challenge. I still succeeded in making a mess.

Is there a better way? Thank you.

I have a large shallow Tupperware container, unhook one at a time, collect then dump

 

[JoeSpartaNJ]

I have a large shallow Tupperware container, unhook one at a time, collect then dump

I have a stainless steel bowl, but I do the same.

 

[kevin58]

What process do you follow for disconnecting pump hoses without dumping beer everywhere?

It seems like I cannot help but make a mess in the kitchen.

With the Anvil 6.5 on the counter, last time I did the following:
1. Shutoff Valve
2. Disconnect hose from spigot
3. Drop hose in bucket that is sitting on the floor
4. Let beer drain

Getting all the beer out (especially on the "out" side of the pump) was still a challenge. I still succeeded in making a mess.

Is there a better way? Thank you.

Put a T valve inline between the pump and the kettle. Not my pic... https://uploads.tapatalk-cdn.com/20210209/8dc2cf506abd9acbe65e781719075a50.jpg

 

[bleme]

What process do you follow for disconnecting pump hoses without dumping beer everywhere?

I brew on the porch, just in case but...
After mash, close valve.
Remove THIS clamp
Hold the sparge arm over a small glass and lift the pump to get as much as I can out.
Put a dish towel under the valve and disconnect
Run hot water through, both ways, while the Anvil gets to boil temp

After chilling, I set the Anvil on a milk crate which puts the valve just over my bucket fermentor, and gravity drain.

 

[NSMikeD]

I got anvil's stainless steel plate for the pump and then added a ball valve and quick disconnect to the outgoing (and a quick disconnect to pump side incoming). I use a camber 1 liter liquid container (the low and wide profile. I shut off the ball locks and put hold the container under the quick disconnects and drain each line individually and them dump the wort back in.

I also have the whirlpool arm and have to disconnect it so it doesn't form a siphon when I unhook the quick disconnect.

 

[RyPA]

I'm considering picking up an Anvil Foundry 10.5g and wanted to get some opinions on my situation.

I currently brew using a 2 vessel system, mash tun + kettle. I heat up my strike water in 2-3 pots on my stove, combine that water into a large kettle to ensure the strike temp is correct and then do my mash. When I have all of my wort, I then heat it using multiple kettles to just below boiling, and then combine it into my large 10g kettle. It's kind of a pain and I like the thought of a single electric vessel with temp control to simply the process.

At the same time, my beers come out good and my system is a pretty well oiled machine after many brews. Looking for opinions from those who went from a similar situation to an Anvil.. is it worth the ~$500 for the simplified brew day?

Thanks

 

[Brewdog80]

In my opinion, yes, I used 3 vessel propane, and system worked, but was just a pain. If yiu have the dough to spend, I would....

 

[GBRbrew]

How long is your brew day? Since I went to the anvil mine is about 6 hrs if I’m hustling and about 8 if I’m being lazy. For most people it’s about shortening and simplifying the brew day the anvil did both for me

 

[RyPA]

How long is your brew day? Since I went to the anvil mine is about 6 hrs if I’m hustling and about 8 if I’m being lazy. For most people it’s about shortening and simplifying the brew day the anvil did both for me

I can finish a brew day with my current setup in around 4.5 hours. But it's a pain juggling multiple kettles on my kitchen stove.

I placed my order for the Foundry, looking forward to trying it.

 

[NSMikeD]

For me, it wasn't so much about shortening the brew day, it did but not in a huge way, but it did make my brew day much easier. I can sit down and relax or attend to tasks while the Foundry does it thing and clean up is easier and quick.

 

[Andres Falconer]

Yes. I haven't given away my kettles, coolers and other now surplus stuff just yet, but I'm not looking back. I've also recently moved to brewbag & pulley and finally got my 220V setup. Massive improvements! Beyond saving time: freeing up the kitchen was a big deal, when brewdays would eat into food preparation time. Being out of the way made brewing less stressful and reduced the risk of contamination. Brewing outside, in good weather, has been amazing. Less stuff to wash, too. Cleaning up was highest on the list of things putting me off from brewing more frequently.

 

[RyPA]

Yes. I haven't given away my kettles, coolers and other now surplus stuff just yet, but I'm not looking back. I've also recently moved to brewbag & pulley and finally got my 220V setup. Massive improvements! Beyond saving time: freeing up the kitchen was a big deal, when brewdays would eat into food preparation time. Being out of the way made brewing less stressful and reduced the risk of contamination. Brewing outside, in good weather, has been amazing. Less stuff to wash, too. Cleaning up was highest on the list of things putting me off from brewing more frequently.

Yeah I'll probably hang on to my traditional equipment as I may end up using it again in the future, you never know.

I plan to eventually get a 240v outlet installed in my garage and then hopefully will be able to run a 20-25ft or so extension cord to make it to my upstairs kitchen for brew day. I ordered the 10g Anvil with only the swirly arm - I plan to buy a brew pump with SS head off of Amazon and get the remaining hardware pieces from brewhardware.com, still trying to figure out what I need specifically. I think I need the below:

- Mash Recirculation Return For Anvil Foundry System
- Camlock fittings for all components - not sure if I should instead use QD fittings. Thoughts?
- Silicone tubing
- Considering picking up this dolly to permanently install the pump to and also as a stand for the Anvil
- Brew bag - can anyone help me out with a good one for the 10.5g?

Can I use a ball-valve to control the pump flow, or do I need some kind of clips for the silicone tubing?

Anything I am missing?

Thanks

 

[tracer bullet]

- Mash Recirculation Return For Anvil Foundry System
- Camlock fittings for all components - not sure if I should instead use QD fittings. Thoughts?
- Silicone tubing
- Considering picking up this dolly to permanently install the pump to and also as a stand for the Anvil
- Brew bag - can anyone help me out with a good one for the 10.5g?

I recirculate with the included pipe. I usually have an inch or two of water above my grains. I can't imagine any other device needing to be added on for it. I think the occasional "lift and lower" of the basket to get the sides mixed in + some stirring every 15 - 20 minutes is plenty.

Camlocks and such are up to you, I just use the worm drive hose clamps (the ones with the key built in). Super cheap and I just don't move enough hoses around to have cared for an upgrade.

Yep some tubing is good, but it comes with enough I think, more than enough.

Good idea, I use a plant stand on wheels LOL. Many pictures around here or the internet for cart setups as well.

Wilser or the one from Anvil directly.

 

[RyPA]

I recirculate with the included pipe. I usually have an inch or two of water above my grains. I can't imagine any other device needing to be added on for it. I think the occasional "lift and lower" of the basket to get the sides mixed in + some stirring every 15 - 20 minutes is plenty.

Camlocks and such are up to you, I just use the worm drive hose clamps (the ones with the key built in). Super cheap and I just don't move enough hoses around to have cared for an upgrade.

Yep some tubing is good, but it comes with enough I think, more than enough.

Good idea, I use a plant stand on wheels LOL. Many pictures around here or the internet for cart setups as well.

Wilser or the one from Anvil directly.

Does it come with a pipe/hose when you do not order the recirculation kit?

 

[Saunassa]

I went to HF and bought the large folding cart. I can fold down the handle and carry into house for winter brewing. In the garage I can roll it outside to clean or into corner for cleanup. Photo it was mashing in a buffalo sweat stout clone. Woke up, water was hot, put in grains and did my morning Teams meeting.