• Please visit and share your knowledge at our sister communities:
  • If you have not, please join our official Homebrewing Facebook Group!

    Homebrewing Facebook Group

A friendly place for friends who drink

Homebrew Talk

Help Support Homebrew Talk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
The only reason I worried at all was because this was the biggest beer I've brewed yet.



Which is kind of sad when I say it out loud.


The biggest beer I've done was 10.2%. It stopped at 1.018, which was about 2 points lower than I even expected.
 
Yussss!

Dry hopped the DIPA today... Lid was off anyway... Had to check again.

1.010! 10.1%... Aiiiiigggghhhht.

View attachment 331089

Whats the trick? Done 9% DIPA, which is fine for me, but I'm limited to 8.5% with RIS. Getting 68% at most with safeale5. Thinking of trying Nottingham next...
 
Whats the trick? Done 9% DIPA, which is fine for me, but I'm limited to 8.5% with RIS. Getting 68% at most with safeale5. Thinking of trying Nottingham next...


Start with a high OG?

Used 2 packs of notty on this one, OG was 1.087.

Why are you limited to 8.5% on an RIS? Space?
 
149f mash, oxygenation is dumping from bucket to bucket 4 times before pitching, done a 61f and 65f fermentation temp and OG between 1.090 and 1.104. But 68% best yet.
 
And just an update. Many have already seen this.

That picture that (I think) was posted in the thread

Ice Car

302947AB00000578-0-image-a-32_1452776811595.jpg


I'm sure y'all are relieved.
 
149f mash, oxygenation is dumping from bucket to bucket 4 times before pitching, done a 61f and 65f fermentation temp and OG between 1.090 and 1.104. But 68% best yet.

Any/all of these might help:
Pitch more cells initially, oxygenate again after 12 hours (open and stir with a spoon if you have to), yeast nutrient, bump the temp when fermentation starts to slow down, and finally pitch fresh yeast if it stalls high.

Took a barleywine from 1.102 down to 1.018 (82%) with WY1056, which is supposed to be the same yeast.
 
149f mash, oxygenation is dumping from bucket to bucket 4 times before pitching, done a 61f and 65f fermentation temp and OG between 1.090 and 1.104. But 68% best yet.

What was your mash ratio? Thinner mashes, 1.5 qts/lb and higher, will attenuate a beer more. Thicker mashes than that do the opposite. If you mashed at 1.25 qts/lb, maybe try thinner next time.
 
What was your mash ratio? Thinner mashes, 1.5 qts/lb and higher, will attenuate a beer more. Thicker mashes than that do the opposite. If you mashed at 1.25 qts/lb, maybe try thinner next time.

Until he confirms, I'm going to say not enough yeast.

I mashed this one @ 2qts/lb... full volume mashing is oosome.
 
How many packs are you pitching?

2pks. I use yeast nutrients also.





Any/all of these might help:
Pitch more cells initially, oxygenate again after 12 hours (open and stir with a spoon if you have to), yeast nutrient, bump the temp when fermentation starts to slow down, and finally pitch fresh yeast if it stalls high.

Took a barleywine from 1.102 down to 1.018 (82%) with WY1056, which is supposed to be the same yeast.

Yes, I've thought about 3pks next time. On the 10-fidy thread guy mentions he uses an aquarium pump for oxygenation. Possible try that after 12hrs as you suggest. I've tried reoxygenating and pitching more to know avail.

Thanks for your tips! I'll try again in a few months.
 
What was your mash ratio? Thinner mashes, 1.5 qts/lb and higher, will attenuate a beer more. Thicker mashes than that do the opposite. If you mashed at 1.25 qts/lb, maybe try thinner next time.

I will look into the specifics. I was looking at just adding more grain to make up the difference, but your indicating, that's not the way to go. Thanks!
 
Back
Top