How to Brew - By John Palmer - Common Off-FlavorsDiacetyl
Diacetyl is most often described as a butter or butterscotch flavor. Smell an unpopped bag of butter flavor microwave popcorn for a good example. It is desired to a degree in many ales, but in some styles (mainly lagers) and circumstances it is unwanted and may even take on rancid overtones. Diacetyl can be the result of the normal fermentation process or the result of a bacterial infection. Diacetyl is produced early in the fermentation cycle by the yeast and is gradually reassimilated towards the end of the fermentation. A brew that experiences a long lag time due to weak yeast or insufficient aeration will produce a lot of diacetyl before the main fermentation begins. In this case there is often more diacetyl than the yeast can consume at the end of fermentation and it can dominate the flavor of the beer.
I don't want to beat a dead horse here, but if my ales are fermenting close to 60°F I won't be likely to develop diacetyl, right? My house is pretty cold and my water bath usually hovers a shade over 60 and I've never tasted diacetyl over the past year that I've been brewing (either that or I have and don't know what it tastes like).
I don't want to beat a dead horse here, but if my ales are fermenting close to 60°F I won't be likely to develop diacetyl, right? My house is pretty cold and my water bath usually hovers a shade over 60 and I've never tasted diacetyl over the past year that I've been brewing (either that or I have and don't know what it tastes like).
I don't want to beat a dead horse here, but if my ales are fermenting close to 60°F I won't be likely to develop diacetyl, right? My house is pretty cold and my water bath usually hovers a shade over 60 and I've never tasted diacetyl over the past year that I've been brewing (either that or I have and don't know what it tastes like).
Diacetyl as a product of fermentation is more characteristic of ales than lagers. Diacetyl is produced early in the fermentation, and then most of it is reabsorbed by the yeast and reduced to flavourless compounds later on. Yeast strains differ markedly in their diacetyl reduction ability. Some ales and a few lagers (such as the famous Pilsner Urquell) contain perceptible amounts of diacetyl, but as a rule modern brewers consider it as a fault. This is because certain bacterial infections and other errors in brewing technique will increase diacetyl levels resulting in unacceptable beer aroma and flavour profile. This parameter thus serves as a quality check. However, it is important to remember that diacetyl flavour is a natural by-product of yeast fermentation, and in some beer styles it is an optional or even required flavour component in low amounts.
Maturation of beer flavour requires the presence of yeast as a catalyst. There are many methods of finishing that have the sole objective of prolonging the contact of beer with yeast after primary fermentation is completed. I want to emphasize that a diacetyl rest with most of the yeast lying at the bottom of the tank and not enough in suspension is of no use. Most lager breweries, especially those that use Weinhenstephan 308 or similar “diacetyl producing yeast’s” employ a long diacetyl rest, in order to minimize diacetyl in the finished beer.
Method 1
If a very cold primary fermentation was used it involves allowing the beer temperature to rise from the controlled primary fermentation temperature of about 10°C to 15-18°C when the primary fermentation is coming to an end. Normally, the time is determined by the attenuation of the beer. If, for example the wort starting gravity was 1050 and the expected terminal gravity is 1010, then the diacetyl rest would be commenced when the beer has attenuated to about SG 1023 when two-thirds of the total fermentable material in the wort has been consumed. The diacetyl rest normally lasts for 48-72 hours, until primary fermentation is over and secondary fermentation is under way. At this time the temperature is lowered when the more traditional method is followed, probably 1°C per day until the lagering temperature of 0-1°C is reached.
Method 2
If a warmer primary fermentation temperature was used for ale or lager the diacetyl rest involves either lowering the beer temperature 2 or 3°C at the end of primary fermentation or keeping it constant for up to 6 days. In lager yeast strains with low diacetyl production it is common practise nowadays to employ a short diacetyl rest followed by centrifuging to remove excess yeast and then crash cooling to 0°C. When brewing ales, that should have very low diacetyl levels especially German Ales like Alt and Kölsch, the implications are to not use highly flocculent yeast and to allow an extended primary fermentation, albeit at cooler temperatures until sufficiently low diacetyl levels are reached. Yeast that settles in the cone is still removed on a daily basis.
The easiest thing I've found for diacetyl is simply time. Give the yeast plenty of time to do what they do and none of the complicated temperature rests are needed, ale or lager.
Enter your email address to join: