Do you remember what is the select one of the three option?. The first not .Try using the other options to flash instead of the NodeMCU. I seem to remember that at least one of my clones didn't work with that flash option.
Do you remember what is the select one of the three option?. The first not .Try using the other options to flash instead of the NodeMCU. I seem to remember that at least one of my clones didn't work with that flash option.
umm after plug Wemos, Fermentrack detect a /dev/ttyAMA0,but dont continued to flash the WEMOS. Its possible to repair Wemos after reflash a new firmware?.
You might consider upgrading to an ESP32. More power. More pins. Only $10.
https://www.amazon.com/HiLetgo®-ESP-WROOM-32-Development-Microcontroller-Integrated/dp/B0718T232Z/ref=sr_1_4?ie=UTF8&qid=1524678872&sr=8-4&keywords=esp32
The ESP8266 firmware doesn't currently work on the ESP32, unfortunately.
That said, who knows what the future might bring...
View attachment 567408
I've been working with both processors. It's easy to write code that works on both.
What 'firmware' are you referring to?
Literally the project I’m working on right now.Hypothetical question - if you get it working on an ESP32 at some point, what would the odds be of getting it to be able to fetch tilt broadcasts and make them available to Fermentrack, so that one doesn't need a RPi there just for the tilt (Thinking in terms of virtualizing Fermentrack)?
...but if anyone has any other features they'd like to request, let me know. The features I'm working on as part of the next release include:
- Revisit "screen scramble" issue
- Allow reenabling the WiFi portal by "double tapping" the reset button
- Test and forcefully reinitialize the EEPROM at first boot for newly flashed controllers
With respect to new feature requests, I know glycol changes have come up in the past. In my case, I'm not glycol, just using an ssbrewtech ftss (coil in my brewbucket with recirculating ice water). I'm guessing any change made for glycol support would apply to my setup as well.
PS. Thanks for the soldered PCBs! They arrived a couple of days ago and look great. I haven't had time to swap them in yet as a couple of unexpected events occupied my time this weekend, but hopefully soon!
I recently added antennas to my ESP8266 brewpi controllers. I'm curious as to any differences in signal strength as a result, which led me to wonder if signal strength could be added to the debug device connection page. Ping response time may also be interesting to have available on this page. Not sure if this is a feature request for fermentrack, brewpi-esp8266 or both, so will just leave here. Cheers.
Also - not sure if anybody else has noticed this - but it seems to me that an eeprom reset is required on the esp8266 if they'd been powered off for extended periods of time. Maybe coincidental, but has happened several times for me. The reset eeprom tool in fermentrack is working like a champ though when I've needed to use it
Which version of Raspbian are you using? Which Raspberry Pi?I am new to Fermentrack but have used brewpi for a year now. I did a fresh install on my Raspberry Pi and it said everything finished correctly.
When I went to the IP Address given it gives me a bad gateway error. I am sure it is something simple that I am just not seeing.
Thanks,
Jeff
Thanks, new to all of this besides installing brewpi with an arduino controller.
Version 8 of Jessie is what it tells me.
Thanks
So I built two boards so I have now tried both, each will not recognize the one wire sensors.
I also re-crimped one sensor as a test sensor. I put a wire in the unused slot on the RJ11 and then sanded down the covering to make the other three fit, I then pulled out the extra wire before crimping so they should all be in the right spot now.
Hopefully something simple on my end. The three pins for Heat, Cool and Door show up as I have the sainsmart relay hooked up so that is at least working.
PM me your address and I can send you an RJ-11 breakout board. You’ll need to solder your own sensors to the board, but that’s itDo you know a reputable place to get a premed one wire from...made 4 myself and all failed so at this point it is most likely me doing something...not sure how the first two from the pack work except for they are soldered directly to the board and not rj11 jacks.
That’s the first I’ve seen a 3M cable...
The Amazon link that day_trippr posted looks like the same vendor as the eBay link but a cheaper price.That’s the first I’ve seen a 3M cable...
Normally it’s either 1M or 2M!
Enter your email address to join: