Search results

Yep, will do. Going to get one tomorrow. Just hope i haven't hurt anything.

Hi people Finally have both a finished (or so i thought) control box, and a 32A circuit. Plugged in my control box for the first time and turned the key. Pop... Fuse dead (i think). The Circuit breaker did not go, so i guess that's a positive. I literally have no idea where to go from here...

So i need 3 more switches? I was trying to do a slightly modified version of this

Sorry i clearly wasn't clear. I have a switch wired to the buzzer like in above, just goes straight from the buzzer to the switch with neutral back to neutral bus.

Can someone please check if wire the alarm buzzer and on/off correctly? It's via the Ezboil 120, 310 and SLY. Put the hot bus to 13 on on the Ezboil 120, then this is wired to 13 on the ezboil 310, and to 2 on the SYL. Wired the 1 to the 14 for the Ezboils, and but not for the SYL (doesn't have...

Ah right, i think i've done that. Put the hot bus to 13 on on the Ezboil, then this is wired to 13 on the ezboil, and to 2 on the SYL. Wired the 1 to the 14 for the Ezboils, and but not for the SYL (doesn't have a 13 + 14). Connected 1 on the SYL to the alarm switch, and this to the alarm...

Oh actually for some reason my DSPR120 does not have connecorts 13+14...

Hi again, sorry this is an addtional question. I'm trying to figure out how to wire int he alarm, from 2 Ezboil, (120 and 320) and a SYL. Alarm wiring appears to be both 1+2 and 13+14. I'm not using a timer, and so will go straight to the alarm and alarm off switch. Can i just wire up the DSPRs...

Thanks Mike Have hooked it up like that. Not just have to connected the alarm and it's done. Cheers Hawk

Hi Mike, could you possible show me how to wire the volt bit of the volt/amp meter? I've followed your design for the amp bit, but not sure where to wire the volt meter wires. Can't figure exactly from the above discussion. Pretty much done after that. Thanks Hawk

Woowzer that's cheap. The build i'm doing now would have cost at least that in parts, not to mention build time...

Even if the Hot wire to the SSR doesn't go through the hot bus?

Thanks. Yep i have looked closely at the Auberins setup. Sadly it is very unclear for those doing more than BIAB setups. Clearly that is their main market. I wonder if putting it before and after the main power coil would work as it connects all the components including the pumps and lights, not...

Thought i should also add, build so far:

Sillbeer, would you by chance have the wiring diagram for that? I've got almost the exact same build going. Just different in i have 4 element ins, and a couple extra switches/lights. Still trying to figure out how to wire that amp/volt meter and the PIDS to the alarm.

Hi all My electric control build progresses slowly. I'm basically wiring straight from the electric brewery instructions with modifications for different set up and components. Wonder if anyone can assist me. I need to wire up the volt/amp meter. It is this one...

Hi all So am going to build my own control box. First off i'm ordering the parts. I decided to go a fully build myself due to the cost of a complete DYI or turn-key system. Also my system is will be a bit unique. I plan on buying from Audering.com all the parts that i cannot source...

Oh and just concluded we have a GFCI in our fuse box. They're called RCD's here and we had to have one installed (i think) when we got an air conditioner installed a few months ago.

Thanks Doug I picked up this and swapped the gas burner for 2 more 2200w 10 amp heating elements (4 x 2200w in total). I also got an additional pump. I'm hoping to use the DSPR310 for the HLT (so i can do step mashes) and the BK. Would be handy to get a temp reader for the mash tun too. On...

Hi all First post here so i'll say a quick 'hi', from down under. I just bought an all electric setup (three vessle 70Ls each - around 17 gallons i think) - to upgrade from my grainfather. The new setup could otherwise be considered just parts so far. What makes it a bit tricky though, is...