Search results

i have beersmith but id prefer a windows laptop, walmart has a rca 10.1 windows tablet/ laptop... does anyone know if this can handle desktop beersmith?

I've been brewing about four years bottles for a couple 2 batches said forget this mess and states kegging... Now I was forced to take a year from brewing so all my equipment has been sittng... I'm transitioning to a 3 vessel system... Ok now the meat n tatters of the question.... (My...

I was thinking about getting a pump to circulate cold water thru my cfc as its georgia and even ground water is too warm to properly chill my wort. I know a sub pump is recommended but what about a bilge pump for a boat could that be an option?

Ok any help is much appreciated... brewstand is finished and test burn went great only burned a min or 2. When i went to test the boil it burned a couple min then went out. Ive tried everything... i have the bg14 burners and a 30psi regulator setup on high pressure.... im assuming its a qcc...

Ive been lookin at getting an inline pump, but I cant find one everywhere and I mean everywhere is sold out... I can only find the center inlet... Im not opposed but I prefer not to have to buy a reducer... I guess im just worried about reducing the flow... Paranoid about burning up the...

I just ordered a barley crusher mill yes yes yes I know its not 3 roller or a monster couldn't swing the finances as a large sum is tied up in fabricating my single tier brew stand... Now where does everyone get their sacks of grain?

I created a starter today... When I started I cleaned the flask and hit it with star san... I get home from work and look at it and I see a few greenish specks on the glass inside at the krasen(spelling wrong im sure). Now a dilemma... Toss and and waste the yeast clean it out better or roll the...

I have been thinking of taking the tops of a keggle im gonna use for a mash tun and converting the top to where a sparge system of some sort could be attached. Has anyone seen this or seen something about this, I cant find anything about making one

I have had a great brew day, until my brothers brother inlaw acted a fool and had to give him a lesson in respect and whos a meaner mofo... I was still a little worked up and I grabbed the wrong yeast... I was gonna use US-05 and I grabbed wine yeast that was in the same color package sitting...

Is it possible to remove the rubber from a keg to make a keggle?

I am about to start cutting steel for my brew stand.but I don't have keggles yet. What are the dimension of a typical keg? And if any one has a good set of schematics fora single tier stand it would save me a lot of time... Any tips would be appreciated

I have a table and old filing cabinet right now as my brew stand. My dad has some old scaffolding that had3 Sets of steps. Today I cut off all the steps to give me 6 6ft tubes of steel. Im saving the steps to use as dividers and to make wind barriers. Im still working on my dimentions. Right...

http://m.ebay.com/itm/111504783248?nav=SEARCH Just saw this for the pinlock groups, I run ball so figured id share some info

I have been extremely lucky in my homebrewing as of recently... For example this past weekend I recieved a kegerator commercially produced, with 2 perlick faucets, various gaskets, cappers, hydrometer, a 7.5 and 5 gal fermenter and 2 ball lock cornys... For the low low price of FREE! Met a guy...

What is a good vacuum sealer that everyone uses to seal hops. Does it need to be a vacuum sealer? I just wanna find a way to preserve my hops, ive ordered a bag sealer as to stop the actual free flowing air. What sealer is recommended by the great people of hbt

I dont have a beer gun or time to make one today. I do have a growler filler. If I purged tye bottles with co2 and used the growler filler, should this work to be able to transport beer in bottles to friends and possibly to bottle for a competition?seems to me like it would work but wanna get...

I am getting a couple kegs and im not sure if they are pin or ball. But cant beat the price... Free... if they are pin would just a post swap be the only necessary thing to convert them to ball? Or are there other things that would need to be done?

Got the option for 1.5 or 2.5 inch. And size hose barb, thinking 2.5 and dont know about barb size... thinking 3/8 ... what do the experts think?

Im ordering ball valve and everything to convert my 10 gal cooler, im getting a 2.5 in instead the 1.5 to ensure clearance so i can hook my manifold up. I was wondering what size barb should i use? 1/2 in or 3/8in?

I have no topic but thought it would be interesting to have a tread to jut have random discussions about water, mash temps, general brew processes, anything brewing related. Just a big random discussion... I'm thinking of building a very random crazy 3 tier Stand using plywood and boards and...