what do i need to know b4 I buy used kegs

[yewtah-brewha]

I found what I believe is the best deal around on used kegs, 4 for 120.00 plus shipping. what should I be aware of, i just want to get kegging as cheaply as possible without comprimising the beer! here is the add.

We just purchased 2,000 Pin Lock kegs! Get them before they are gone!! They are only available at this price in lots of four.


Pressure tested 5 gallon, Pin lock, stainless steel, cornelius style tank. These tanks are guaranteed to hold pressure. Tanks show normal wear & tear. Pin Lock lids.

22" tall x 9" in Diameter

Kegs are fully assembled - optional new parts are below. Example: If you want new o-rings, check the box below.



We know some homebrewers are more picky than others, so please keep in mind that these are USED pin lock kegs. Some of these kegs are probably 30 years old. Do not expect new kegs. If you are looking for new kegs, please check out our new kegs. We try and have quality kegs available at all times. With this said, they are going to show normal wear and tear. We try not to purchase from Pepsi or Coke to avoid heavily used kegs. We are not implying that our kegs are not quality...we just want to avoid any misunderstandings.


If you are unhappy with your used 5 Gallon Pin Lock Cornelius Kegs for any reason, we will gladly take them back. The purchaser will be responsible for return shipping charges.

 

[Golddiggie]

Are you set up for pin lock kegs? If not, then you'll either need to get some pin lock QD's or convert them over to ball lock kegs. You'll also need to get/make a wrench for removing the posts for maintenance, if you don't already have one. You won't be able to use a standard wrench/socket like you can with ball lock kegs.

Also be aware that they are fatter than ball lock kegs, so you'll fit less of them in a keezer/fridge. Where you might fit four ball locks in the keezer, you might only get three pin locks in there.

If all that doesn't matter, then I'd get the new o-ring set with them. Provided they don't charge too much (most places charge under $3 for a complete set of o-rings for a keg, some even include a free set with their used kegs). I would also check to see how long they'll give you to decide if you're happy with the kegs, or not. If it's less time than you'll be able to give them a proper test, I'd pass. Nothing sucks more than to fill a keg, hit it with CO2 to seal only to have it leak like the Titanic.

IME, if something sounds too good to be true, it usually is.

 

[Doc_Trax]

Nothing wrong with pin lock kegs. You don't accidently put the gas on the liquid post either. If I didn't have lots of other kegs, I would buy pins.

 

[Golddiggie]

Nothing wrong with pin lock kegs. You don't accidently put the gas on the liquid post either. If I didn't have lots of other kegs, I would buy pins.

I've never put the wrong QD onto a ball lock keg. Only takes a glance to know which post to use. On the newer/new kegs it's even easier, since they only have one handle. Plus they have 'in' and/or 'out' stamped on them near the posts, so it doesn't take much brain power to figure it out.

 

[BBL_Brewer]

Try not to get any challenger kegs with the plastic gas in dip tube.

 

[yewtah-brewha]

good info, thanks. I would deffinatly test b4 filling with beer, that would suck to find out it doesnt seal. and they charge 3.00 for 1 keg

 

[chickypad]

Only takes a glance to know which post to use. On the newer/new kegs it's even easier, since they only have one handle. Plus they have 'in' and/or 'out' stamped on them near the posts, so it doesn't take much brain power to figure it out.

But all this assumes you are sober enough to see straight. Been there, done that

 

[Golddiggie]

But all this assumes you are sober enough to see straight. Been there, done that

If I'm that far in the bag, then I'm too far gone to even think about changing a keg over. It can always wait until the following day.

 

[Hackwood]

$25-$30 is pretty darned good as long as they seal. I regularly see them for $50-$60 used and have been able to hold off and find more at the lower price. I just picked up 9 ball-locks over the weekend for $235. $26.11 per.

 

[zeekage]

Just know that pin lock kegs are shorter and fatter than ball lock kegs. I think an inch or two shorter and .5 inches fatter. If you're trying to jam as many as possible in a keezer, then pin lock might not be the best for you since the floor space is your limiting factor. If you don't think size is a big issue then its really personal preference. One other downside to pinlock is that they often don't have a pressure release valve in the lid. It's usually easy enough to press the poppet down with your finger or something to relieve pressure. Pin locks are usually cheaper than ball locks too, so that's a plus side for them.

Just more FYI's so you can make an informed decision.

 

[yewtah-brewha]

$25-$30 is pretty darned good as long as they seal. I regularly see them for $50-$60 used and have been able to hold off and find more at the lower price. I just picked up 9 ball-locks over the weekend for $235. $26.11 per.

was this a one time special? if not where?

 

[Hackwood]

was this a one time special? if not where?

Craigslist deals. Patience sometimes pays.

 

[acidrain]

Picked up 2 pin-locks, a nice burner, and two cappers for $50 today.
I don't use pin locks, but it was a good deal, so...
Yeah, I look at craigslist everyday.