plastic fermenter lifespan

[tomwhit19]

just curious if anyone has a recommended lifespan for plastic fermenters? i.e. the big mouth bubbler

i only ask because i read awhile back about how plastic gets scratched and flavors can get trapped or absorbed into the plastic

 

[IslandLizard]

They're made from PET, it's pretty impervious to flavors and aromas. Whatever gets absorbed is so minimal, you'd never notice.

As long as you don't scratch them, they can last pretty much forever. Even small inner surface scratches should be cleanable and sanitizable.

I'd use a warm water soak (add a little Oxiclean) followed by a thorough wipe with a small washcloth drenched in some dissolved PBW to clean them. Then a different washcloth soaked in Starsan to sanitize.

 

[hottpeper13]

I use these for primary and found the purple sponge is totally scratch free. I think it's a 3M product. when I first saw them I thought they would be good for my cast iron and boy was I wrong. Only use 'em on plastic, got 2 plastic big mouth when they first came out and don't have any scratches and are brightly clear. On the other hand my friend has 2 pet better bottles that are all foggy from using a carboy pressure cleaner and pbw,and he says he had contaminated beer twice and uses them only for hauling water for brewing.

 

[GHBWNY]

My BMBs are clear as a bell and do not smell. My plastic buckets, however, have retained the (delightful) aroma of 5 years-worth of brews, regardless of thorough cleaning/sanitizing before and after each session. Probably micro-scratches or simply the micro-porosity of the material, but I'm not worried.

As for "life-span" of one or the other, I'll use them until I suspect there is evidence of a problem.

 

[IslandLizard]

[Plastic buckets] Probably micro-scratches or simply the micro-porosity of the material, but I'm not worried.

It's just discoloring. I put them in bright sunlight for a few days, they seem to bleach up a bit. But as you said, nothing to worry about.

 

[njviking]

I still have my first bucket from 1991. Scratched to hell and permanentley smelling like ekg.

Sanitary practices I believe are most relavent in situations like this. I get paecilomyces in buckets from time to time especially in the summer. I just soak them in a stronger solution of bleach for a couple days and it seems to keep it away .

 

[IslandLizard]

I still have my first bucket from 1991. Scratched to hell and permanentley smelling like ekg.

You still use that for beer fermentations?

I get paecilomyces in buckets from time to time

What does that look like in your bucket? Does it have a color?

 

[kh54s10]

I use Better Bottles and buckets. About 7 of them of different sizes, mostly 6 gallon of the BB. I bought all of them from 2011 to 2014, none have been retired.

I soak in Oxyclean (generics). Rinse, put a dish cloth inside and swirl until I can no longer see any bits sticking to the inside, rinse some more. Dry and store. On brew day, rinse out any dust etc, add a cup or so of Starsan, swirl it. Then I let it sit for a few minutes. When ready to drain the wort into the BB, I pour the Starsan back into it's container and drain the BK.

 

[passedpawn]

just curious if anyone has a recommended lifespan for plastic fermenters? i.e. the big mouth bubbler

i only ask because i read awhile back about how plastic gets scratched and flavors can get trapped or absorbed into the plastic

I've got a LOT of experience with clear PET fermentors. I never got a single scratch inside them. One of my better bottles developed a crack on the bottom from usage - probably me tilting it while full. I've got six of the big mouth bubblers now.

If you clean them right after emptying, they are pretty easy to clean up with a sponge or other mildly abrasive tool. If I dry-hopped the beer and there is a tough ring of gunk, I usually just fill with oxyclean solution and let sit for a day, then sponge cleans it right up.

I expect these BMB's to last the lifetime of my brewing. Time will tell.

 

[passedpawn]

I use Better Bottles and buckets. About 7 of them of different sizes, mostly 6 gallon of the BB. I bought all of them from 2011 to 2014, none have been retired.

I soak in Oxyclean (generics). Rinse, put a dish cloth inside and swirl until I can no longer see any bits sticking to the inside, rinse some more. Dry and store. On brew day, rinse out any dust etc, add a cup or so of Starsan, swirl it. Then I let it sit for a few minutes. When ready to drain the wort into the BB, I pour the Starsan back into it's container and drain the BK.

After cleaning my fermentors, I add the cup of starsan, swirl, and store that way. On brewday, swirl, remove the lid, dump starsan, and add wort. I don't use any starsan on brewday at all

 

[kh54s10]

After cleaning my fermentors, I add the cup of starsan, swirl, and store that way. On brewday, swirl, remove the lid, dump starsan, and add wort. I don't use any starsan on brewday at all

Pretty much the same. I just do it on the next brew day, not packaging day. (or the day after - depending on how much dried up gunk!)

Better Bottles don't have a lid. And I don't have any solid bungs. So I would have to use plastic wrap and rubber bands. - too much trouble for me.....

 

[njviking]

You still use that for beer fermentations? yep. got an oatmeal stout for st pats day ready to come out of it in the next few days.

What does that look like in your bucket? Does it have a color?

Pink circles.
I don't think you ever get rid of it; although I'm the type of person that doesn't necessarily follow a close reimine whe it comes to sanitary practices.

In almost 30 years of brewing though; I can count on one hand how many infections I've had in my brews.

 

[IslandLizard]

After cleaning my fermentors, I add the cup of starsan, swirl, and store that way. On brewday, swirl, remove the lid, dump starsan, and add wort. I don't use any starsan on brewday at all

I think it's better after a Starsan treatment to pour it out and let them air dry.

Most compelling After a few weeks the (inside) headspace and bottom of the lid of my loosely lidded Starsan buckets develop gray/black mold dots. I reckon it's due to evaporation and re-condensation.

Now the strangest thing is, I never noticed those spots inside my glass carboys. I always leave them with a few inches of Starsan in them, and plastic wrap around the opening.

Maybe the bucket plastic is more susceptible to mold growth while PET and glass is not? Or not as visible.

 

[SEndorf]

I ferment in two 6 gallon BMB's and also a Spidel. I fill with PBW and let soak for a few days, then empty and fill with a few gallons of rinse water and shake. Do this about three or four times, then upside down to dry thoroughly. I don't sanitize until brew day.
None of these plastic fermenters have seen a sponge or rag.
I can count on one fist how many infections I've had..

 

[IslandLizard]

Pink circles.
I don't think you ever get rid of it; although I'm the type of person that doesn't necessarily follow a close reimine whe it comes to sanitary practices.

In almost 30 years of brewing though; I can count on one hand how many infections I've had in my brews.

Thanks!
I think I've seen those on or near krausen rings after a few weeks when I had forgotten to clean the buckets.

Plastic drinking cups (in the bathroom) that stay damp or with small bits of water left in them also seem to develop a pink residue on the bottom after a few weeks. Wonder if that's the same strain. They get cleaned and washed much more often now.

 

[catdaddy66]

just curious if anyone has a recommended lifespan for plastic fermenters? i.e. the big mouth bubbler

i only ask because i read awhile back about how plastic gets scratched and flavors can get trapped or absorbed into the plastic

I have used my bmb for 4 years and never had an issue. I use soft cloth and hot water with either starsan or an ounce of chlorine bleach (if cleaning is needed). I clean them the same day I bottle so when they are ready for fermentation they only need sanitizing.

No bad batches since I switched from buckets.

 

[passedpawn]

Better Bottles don't have a lid.

I just put the airlock and universal bung back into those after cleaning.

I think it's better after a Starsan treatment to pour it out and let them air dry.

Most compelling After a few weeks the (inside) headspace and bottom of the lid of my loosely lidded Starsan buckets develop gray/black mold dots. I reckon it's due to evaporation and re-condensation.

The only time I had anything grow inside one of my stored fermentors was once when I washed but did not add the starsan. I likely put it away with some water remaining in there, and some black mold grew. I've never had anything like that when I did the starsan swirl method (and I store them in my Florida garage, where mold grows quite well). But you know, I'm not trying to convince anybody here that one way is better than the other - it's just what has worked for me. I store my kegs the same exact way.

 

[DocScott]

I had to get new buckets after about 7 years. I had two batches in a row go bad and finally realized I had used my buckets to empty out my kids’ inflatable pool and fell out of my normal routine. Haven’t had trouble before or since with similar cleaning to the aforementioned processes.

 

[Calder]

I'm still using 2 of 3 HDPE fermenters I bought 35 years ago. The bottom cracked on one of them and started a small leak out of the bottom. Never lost any beer, just left a small pool of liquid on the ground. I have beer in one of them right now.

I had a BMB last about 2 years. It developed blisters on the inside walls, and I eventually stopped trusting that they would not burst and harbor germs. I used to keep a couple of inches of mild bleach solution in the bottom of it when not in use, I think the bleach was the cause of the problem. I have 2 replacement BMBs and both are doing fine, I clean and sanitize after each use, and store dry upside down allowing to air dry.

 

[Moose_MI]

4-ev-r

 

[Immocles]

This thread makes me feel good about my bucket and bmb future haha. I have one of each.

 

[odie]

Still using my original 6? Gal bucket from 1994...have an IPA in it right now. I never ever used it for anything else and soft scrubbers.

 

[tomwhit19]

thanks everyone, just trying to process of elimination a problem i seem to be having lately....seems like every beer comes out with the same "taste" in it and i cant pin point it, and theres no homebrewers i know in my area that i can have taste it and maybe have some input on what this "taste" is so i was figuring maybe micro scratches in my bmbs were contributing to it

 

[LittleRiver]

... every beer comes out with the same "taste" in it and i cant pin point it...

Have you completely disassembled, thoroughly cleaned, and sanitized everything? I read an account of a similar situation, and it turned out to be the drain valve in his kettle.

 

[troypolla]

thanks everyone, just trying to process of elimination a problem i seem to be having lately....seems like every beer comes out with the same "taste" in it and i cant pin point it, and theres no homebrewers i know in my area that i can have taste it and maybe have some input on what this "taste" is so i was figuring maybe micro scratches in my bmbs were contributing to it

You can bottle and ship it all to me and I’ll check it for you. One bottle at a time. [emoji3]

 

[LuckyBeagleBrewing]

I have been using some old Spagnol 11.2 gallon HDPE fermenters for at least 7 years and I will keep using them even after I get stainless. They have been great fermenters and clean up great. No internal scratches that I have seen and no infections in that time.

 

[IslandLizard]

Have you completely disassembled, thoroughly cleaned, and sanitized everything? I read an account of a similar situation, and it turned out to be the drain valve in his kettle.

All of this^

Inspect, clean, and sanitize every piece and every nook and cranny. Spigots on bottling buckets are notorious. But will separate after a soak in some hot water then pushed apart.

Racking canes, hoses, bottle wands, everything that touches your chilled wort or beer.

 

[NGD]

I think it's better after a Starsan treatment to pour it out and let them air dry.

Most compelling After a few weeks the (inside) headspace and bottom of the lid of my loosely lidded Starsan buckets develop gray/black mold dots. I reckon it's due to evaporation and re-condensation.

Now the strangest thing is, I never noticed those spots inside my glass carboys. I always leave them with a few inches of Starsan in them, and plastic wrap around the opening.

Maybe the bucket plastic is more susceptible to mold growth while PET and glass is not? Or not as visible.

Recently tried to store a batch of Starsan to have on hand. Just noticed black mold under the lid on my bucket as well. Probably last time I’ll do that.

 

[IslandLizard]

Recently tried to store a batch of Starsan to have on hand. Just noticed black mold under the lid on my bucket as well. Probably last time I’ll do that.

If you sanitize the exposed walls of the headspace and the (bottom of the) lid, it takes several weeks for that mold to appear. I never push the lid shut on the Starsan storage buckets, just lay them loosely on top. I guess air gets in and allows that mold to grow (faster). Ambient temps are a factor too.

Just resanitize the headspaces and lids more frequently. I mop it around using a small washcloth.

I don't see it as a real problem, I just wash it off and resanitize. If you fill the buckets to the brim leaving no or little headspace it may not happen.

 

[GHBWNY]

Recently tried to store a batch of Starsan to have on hand. Just noticed black mold under the lid on my bucket as well. Probably last time I’ll do that.

I suspect that recycling the Star-San carries some micro-debris with it. The underside of a bucket lid would seem to be the perfect environment for mold: dark and damp. I keep my Star-San in a clear 3-gal PET water bottle with a cap. Plus, I don't push it past 2-3 batches of use; it's not worth an infected brew for the cost of mixing up a new batch of sanitizer. I mix about 1.5 - 2 gal at a time and always shake it vigorously just before use so that it's as foamy as can be. Maybe the clear bottle with a narrow neck where moisture can't as easily accumulate is why I've never had an issue with mold inside the bottle.