Haier 7.1 cu ft freezer for $175 at Costco

[frothus]

I mounted an outlet box inside mine with a duplex outlet. One outlet is wired to always on and I plug a wall wart into it to power my fan. The other outlet is for a heater and is switched by an externally mounted STC-1000

You aren't worried about having a 110V outlet in such a humid environment?

Sent from my SCH-I535 using Home Brew mobile app

 

[LanceBoyle]

What did you hook the case fans to for power? Just an ac adapter? Any recommendations?

I had a bunch of low voltage dc wall wart adapters laying around and used a couple of those, one for each fan. I cut off the dc plug and connected them to the fans with some heat-shrink tubing. A little on the lame side, but they are working fine. They are 12cm case fans not mm, as I originally posted, btw. You can also buy a 120v version on amazon, just search for muffin fan, less than $20 if I remember.

 

[srice]

You aren't worried about having a 110V outlet in such a humid environment?

Sent from my SCH-I535 using Home Brew mobile app

Nope - got it on a GFCI

 

[pattatat]

Just picked this up yesterday at Sam's for 179.

When you say 4 fit tight on the floor, you guys aren't kidding. It has to be wedged in there. (Ball locks)
It even slightly dents the wall of the freezer but shouldn't be an issue.

 

[coyotebrew]

Anyone know what the wattage draw is on this freezer? (Off grid)

 

[shigadeyo]

Just picked this up yesterday at Sam's for 179.

When you say 4 fit tight on the floor, you guys aren't kidding. It has to be wedged in there. (Ball locks)
It even slightly dents the wall of the freezer but shouldn't be an issue.

Was the one you got the new Haier HF71CL53NW model? If so, it still fits 3 kegs without a collar?

 

[Smithinc49]

Will 27" be high enough to hit a standard sanke coupler?

 

[dad311]

I want to thank everyone that posted before me. My old Keezer failed with 20 gal of newly brewed beer inside. After reading earlier posts, I bought the HF71CL53NW freezer from Sams Club and quickly built (in 26 hours) a new Keezer. The Keezer will hold 4 ball lock kegs and 1 20lb tank using a 2x8 collar.

Thanks again!

 

[iamthesnee]

Does anyone who has this know if I could squeeze 4 pin locks in there if I use a collar? Would it take 3 on the bottom and one on the hump or is it too tight?

 

[MikeInMKE]

Does anyone who has this know if I could squeeze 4 pin locks in there if I use a collar? Would it take 3 on the bottom and one on the hump or is it too tight?

It's tight, but I can fit 4 ball-lock (8 inch diameter) kegs on the floor of this freezer. And with a tall enough collar, another one on the hump.

I have no doubt that you could fit 3 pin-lock (9 inch diameter) kegs on the floor, and another pin-lock on the hump with a tall enough collar.

 

[Gavin C]

It's tight, but I can fit 4 ball-lock (8 inch diameter) kegs on the floor of this freezer. And with a tall enough collar, another one on the hump.



I have no doubt that you could fit 3 pin-lock (9 inch diameter) kegs on the floor, and another pin-lock on the hump with a tall enough collar.

It would be very tight.View attachment ImageUploadedByHome Brew1451777944.521411.jpgView attachment ImageUploadedByHome Brew1451777977.334813.jpg

 

[universalfrost]

Thanks For the great thread...Going to pickup one of these at my Sam's club....

 

[derekcw83]

I have one and fit 4 5g cornys on the floor, and a 3g corny plus my 10 lb tank on the compressor shelf. Maybe that's been mentioned but I don't have time to read through all the posts.

 

[universalfrost]

I'm gonna build with high enough collar to get 3 pin locks on the floor and a 4th on the hump ... That way 3 brews on tap at any time and 1 carbing or doing a cold crash or lager in another 4th keg..

 

[srice]

I was just at Costco during lunch and saw that they have replaced the Haier freezer with a 7.2 cu ft one from HiSense. It was $109 after a $30 instant rebate. If I needed a new one, I would be all over that.