Hoosierbilly
Well-Known Member
I am selling my 1BBL brewery. I down graded from 2bbl to 1bbl but I find it sits around more than it is brewed on. I have brewed probably 10 batches with this setup. Not my first set of stainless vessels, very well cared for, in like-new condition, no dents, nicks, scratches, or discoloration. Cleaned with BKF and stored inside. I get efficiency in the low 80’s. I find myself doing more smaller batches and would like to see this put to use in a brewery where it belongs. This uses a 50 amp 4-prong outlet. The control panel is the electric brewery 50amp control panel for 30+ gallons that was pre-asymbled by them, with their control panel power cord.
https://shop.theelectricbrewery.com...ry-control-panel-for-30-gallons-pre-assembled
https://shop.theelectricbrewery.com/products/control-panel-power-cord-50a-pre-assembled
The vessels are stout tanks:
40gal HLT, similar to this except with 2 element ports
https://conical-fermenter.com/1-bbl-hot-liquor-tank-HL40TW-HC-SG-379.html
40gal MT and 12″ sparge arm
https://conical-fermenter.com/1-bbl-Mash-Tun-486.html
https://conical-fermenter.com/Sparge-Arm-12.html
45gal BK
https://conical-fermenter.com/45-Ga...et-Sight-Glass-Electrical-Ports-and-legs.html
The control panel connects to 4 5500w all stainless elements (two in HLT and two in BK) with grounded TC connections. Two twist lock cords included for powering pumps.
https://shop.theelectricbrewery.com...-5500w-240v-camco-02935-straight-bare-element
https://www.brewhardware.com/product_p/etc3.htm
Each vessel has a TC temp sensor with color coded cables to the control panel (Red for mash, white for water, blue for boil)
https://shop.theelectricbrewery.com...1-5-tri-clamp-temperature-probe-pre-assembled
For recirculating, whirlpooing, and cooling in the BK is a march nanobrewery pump.
https://www.morebeer.com/products/m...haJEt0Xp1Fqx18O30BP8f1iJc3pal7ZhoChhEQAvD_BwE
For mash recirculation is a 12v DC pump
https://www.brewershardware.com/Pumps/topsflo-dc-brewing-pumps/
Jaded Hydra Chiller
https://jadedbrewing.com/products/the-hydra
SSbrewtech 1bbl chronical brewmaster edition with cooling coil and neoprene sleeve
https://www.morebeer.com/products/s...RbZg1wki0dnR76GRNAzd6XGRsYe5laPxoC7AsQAvD_BwE
Included is all silicone hoses, hose clamps, triclamps, gaskets, and any and all fittings needed for brewing. No plastic or pvc touches the wort, only stainless and silicone.
Asking $8,000. Equipment is in like-new condition, only brewed on about 10 times. Located in central IN, local pickup only. Good Luck. Cheers!
https://shop.theelectricbrewery.com...ry-control-panel-for-30-gallons-pre-assembled
https://shop.theelectricbrewery.com/products/control-panel-power-cord-50a-pre-assembled
The vessels are stout tanks:
40gal HLT, similar to this except with 2 element ports
https://conical-fermenter.com/1-bbl-hot-liquor-tank-HL40TW-HC-SG-379.html
40gal MT and 12″ sparge arm
https://conical-fermenter.com/1-bbl-Mash-Tun-486.html
https://conical-fermenter.com/Sparge-Arm-12.html
45gal BK
https://conical-fermenter.com/45-Ga...et-Sight-Glass-Electrical-Ports-and-legs.html
The control panel connects to 4 5500w all stainless elements (two in HLT and two in BK) with grounded TC connections. Two twist lock cords included for powering pumps.
https://shop.theelectricbrewery.com...-5500w-240v-camco-02935-straight-bare-element
https://www.brewhardware.com/product_p/etc3.htm
Each vessel has a TC temp sensor with color coded cables to the control panel (Red for mash, white for water, blue for boil)
https://shop.theelectricbrewery.com...1-5-tri-clamp-temperature-probe-pre-assembled
For recirculating, whirlpooing, and cooling in the BK is a march nanobrewery pump.
https://www.morebeer.com/products/m...haJEt0Xp1Fqx18O30BP8f1iJc3pal7ZhoChhEQAvD_BwE
For mash recirculation is a 12v DC pump
https://www.brewershardware.com/Pumps/topsflo-dc-brewing-pumps/
Jaded Hydra Chiller
https://jadedbrewing.com/products/the-hydra
SSbrewtech 1bbl chronical brewmaster edition with cooling coil and neoprene sleeve
https://www.morebeer.com/products/s...RbZg1wki0dnR76GRNAzd6XGRsYe5laPxoC7AsQAvD_BwE
Included is all silicone hoses, hose clamps, triclamps, gaskets, and any and all fittings needed for brewing. No plastic or pvc touches the wort, only stainless and silicone.
Asking $8,000. Equipment is in like-new condition, only brewed on about 10 times. Located in central IN, local pickup only. Good Luck. Cheers!
Last edited: