Mini Keezer with Coke Bottle?

[pabmadi]

Hi; I want to build a mini Keezer around a peltier refrigerator of 32 litres. I want to use Co2 bicycle inflator and 3 litres Coke bottles; some build something similar?

My biggest issue is the tap for Coke bottle, any advice on how to do it ?

 

[pabmadi]

I think I can build something like this:

 

[BeardedBrews]

You could use this:
https://www.aliexpress.com/item/Pic...ith-Portable-Co2-Keg-Charger/32746393588.html
or
https://www.aliexpress.com/item/NEW...quid-Disconnect-Kit-HomeBrew/32763931258.html

With this
https://www.aliexpress.com/item/Pre...ck-fitting-mini-CO2-Regulator/1676892448.html

And then one of these for each 3L Bottle:
https://www.aliexpress.com/item/Sta...e-fit-soft-drink-PET-bottles/32411595254.html



If you already have the CO2 charger you could piece together your own kit.

 

[pabmadi]

You could use this:
https://www.aliexpress.com/item/Pic...ith-Portable-Co2-Keg-Charger/32746393588.html
or
https://www.aliexpress.com/item/NEW...quid-Disconnect-Kit-HomeBrew/32763931258.html

With this
https://www.aliexpress.com/item/Pre...ck-fitting-mini-CO2-Regulator/1676892448.html

And then one of these for each 3L Bottle:
https://www.aliexpress.com/item/Sta...e-fit-soft-drink-PET-bottles/32411595254.html



If you already have the CO2 charger you could piece together your own kit.

THANKS! My doub is; if I use this cap:

I need to put a tube to the booton of the bottle to dispense the beer; and if I do that; when I put Co2 this Co2 will make some boubles in the beer, I don't know if that will be a problem...

If I want to use 2 bottle and 1 Co2 tank, is there any adapter to use it?

 

[camiller]

IIRC most 3L bottles have a wider mouth than 2L bottles. I don't think that carbonater cap will work, heck where I live we never see 3L bottles, I have to go back to where I grew up to see them. There is no reason you couldn't stick with what you have in post 2 and if you want two or more off the same charger simply run tubing with the appropriate fitting to where the picture shows the co2 charger hooked up then hook them to a "T"/"Y" fitting that then connects to the single charger/tank.

 

[BeardedBrews]

I need to put a tube to the booton of the bottle to dispense the beer; and if I do that; when I put Co2 this Co2 will make some boubles in the beer, I don't know if that will be a problem...

If I want to use 2 bottle and 1 Co2 tank, is there any adapter to use it?

Putting the CO2 in the bottom and causing bubbles will not be a problem, but you do have to be careful not to let beer suck back into your CO2. If you had a bottle at 20psi, and then put on a gas connection at 10psi it would force beer up the tube and into your regulator.

 

[pabmadi]

Epic fail on my firts DIY trial... The tee was very thin for the drill...

 

[pabmadi]

Second chance... A little bit more bulky

 

[phug]

Looks clean

 

[pabmadi]

Some progress

 

[pabmadi]

[ame]https://www.youtube.com/watch?v=Qsnj7N6mYUw[/ame]

I have some gas liking... I need to seal it ...