FloppyKnockers
Well-Known Member
I wanted some cool tap handles. At first I wanted ones that had the name of the beer that I brewed on it, but no dry erase or chalkboard. After deciding that thats one helluva collection I would amass, that idea was discarded. Then I thought I wanted a few cool commercial ones
that idea was vetoed. Then I decided I wanted a couple fictitious beers. The choices were many, but I finally decided on Pawtucket Patriot Ale from Family Guy and Duff from The Simpsons. Close runner up and on the block next are Shotz from Laverne & Shirley and Alamo from King of the Hill.
Now that I know what I want, I just need to find it. Good luck on that. I could not find either of those for sale anywhere, much less one I liked so I decided to make them. So now I just needed some plans to make a couple, right? Nope. A good scouring of the internet machine delivered less than nothing.
I know I wanted an older style one for Pawtucket and a more modern one for Duff. Well start with Duff.
I started with three pieces of poplar glued up to get a chunk about 2 1/2 square, 11 long.
I knocked the corners off with the table saw then rounded it off. Then I made some reference marks at critical points like the bead, top, and thickest part.
I got a label badge for the Duff logo at Rockler http://www.rockler.com/beer-tap-component-hardware. To make sure it fits nicely, I turned the blank down to the diameter of the back of the badge.
After getting the right diameter, I turned that shape that best resembled a tap handle. Sanded to 400 grit and off to the paint shop.
Now, I got pretty into the next part so I lacked in the picture department, but next I screwed in the hangar bolt that came with this guy, also from Rockler http://www.rockler.com/beer-tap-component-hardware-beer-tap-ferrule . I put a couple coats of red paint on then I found a picture of Duffman, cut it out and spray adhesived him to the handle. To finish it off I put several coats of spray auto body clear coat on. Put the badge on. Glued a Duff logo to it (also printed out), then BAM done.
Next I worked on the Pawtucket. This one was just two pieces of walnut glued up to get a blank about 1 ½ square and about 6 long. It does not need to be as long as the Duff because this is going to be a three-piece handle and were making only two of them here.
I didnt really have a plan for the profile I just kinda went for it. I knew the top had to be longer than the bottom and the center needed to be turned down to 5/16 for dowels to meet the holes in the middle.
As far as the image goes, I know I wanted something old looking to go with the look of the handle. I found this video on youtube that instructs you how to transfer inkjet printer images to wood.
[ame]https://www.youtube.com/watch?v=eod2hvqgTBY[/ame]
Heres all three pieces
After transferring the image of the logo I found on the Goog (both sides), it was time to trim out the edges with a bit of walnut to hide the edges.
I threaded a threaded nut into the bottom of the bottom piece and drilled holes in the top and bottom of the image before gluing it all together. I didnt want this one too glossy so I hit it with a few coats of semi-gloss lacquer.
It took a few days (a lot of dry time) to complete these and I have to say that Im pretty happy with the outcome. I cant wait to do more.
Hope this helps out.
Now that I know what I want, I just need to find it. Good luck on that. I could not find either of those for sale anywhere, much less one I liked so I decided to make them. So now I just needed some plans to make a couple, right? Nope. A good scouring of the internet machine delivered less than nothing.
I know I wanted an older style one for Pawtucket and a more modern one for Duff. Well start with Duff.
I started with three pieces of poplar glued up to get a chunk about 2 1/2 square, 11 long.
I knocked the corners off with the table saw then rounded it off. Then I made some reference marks at critical points like the bead, top, and thickest part.
I got a label badge for the Duff logo at Rockler http://www.rockler.com/beer-tap-component-hardware. To make sure it fits nicely, I turned the blank down to the diameter of the back of the badge.
After getting the right diameter, I turned that shape that best resembled a tap handle. Sanded to 400 grit and off to the paint shop.
Now, I got pretty into the next part so I lacked in the picture department, but next I screwed in the hangar bolt that came with this guy, also from Rockler http://www.rockler.com/beer-tap-component-hardware-beer-tap-ferrule . I put a couple coats of red paint on then I found a picture of Duffman, cut it out and spray adhesived him to the handle. To finish it off I put several coats of spray auto body clear coat on. Put the badge on. Glued a Duff logo to it (also printed out), then BAM done.
Next I worked on the Pawtucket. This one was just two pieces of walnut glued up to get a blank about 1 ½ square and about 6 long. It does not need to be as long as the Duff because this is going to be a three-piece handle and were making only two of them here.
I didnt really have a plan for the profile I just kinda went for it. I knew the top had to be longer than the bottom and the center needed to be turned down to 5/16 for dowels to meet the holes in the middle.
As far as the image goes, I know I wanted something old looking to go with the look of the handle. I found this video on youtube that instructs you how to transfer inkjet printer images to wood.
[ame]https://www.youtube.com/watch?v=eod2hvqgTBY[/ame]
Heres all three pieces
After transferring the image of the logo I found on the Goog (both sides), it was time to trim out the edges with a bit of walnut to hide the edges.
I threaded a threaded nut into the bottom of the bottom piece and drilled holes in the top and bottom of the image before gluing it all together. I didnt want this one too glossy so I hit it with a few coats of semi-gloss lacquer.
It took a few days (a lot of dry time) to complete these and I have to say that Im pretty happy with the outcome. I cant wait to do more.
Hope this helps out.