Ok, Here's the pieces and parts:
Estimation of total spent on card: $630.00
(I'm sure I forgot something so I'll edit the post if something comes to mind)
The steel tubing:
1 1/2" x 1 1/2" 14 gauge
(4 count) 62" pieces
(8 count) 17" for the vertical legs
(8 count) 13.5" for the corners and keg holders
(12 count) 7" wide x 8" tall plates for the burner mounts.
I had a 3/8" slit plasma cut into each, I think it's 4" tall
Cost: Beer
Ebay casters from sescasterco:
"Caster 5". Total Lock Threaded Stem. Rubber Wheel"
Cost: $8.29 a piece
They require a 1/2" hole, so have a sharp drill bit.
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=150385618042&ru=http%3A%2F%2Fshop.ebay.com%3A80%2F%3F_from%3DR40%26_trksid%3Dp3692.m570.l1313%26_nkw%3D150385618042%26_sacat%3DSee-All-Categories%26_fvi%3D1&_rdc=1
Stainless washers and stainless nylon lock nuts for the casters - hardware store
BG-14 burners
Supplier: Agrisupply
www.agrisupply.com
http://www.agrisupply.com/product.asp?pn=64494
Cost: $29.95 each
And the High pressure adjustable regulator
http://www.agrisupply.com/product.asp?pn=64484&sid=&eid=
Cost: $19.95
And the LP gas hose assembly
http://www.agrisupply.com/product.asp?pn=36108&sid=&eid=
Cost: $5.99
Hardware store:
This hardware is to connect the burner to the plates. There is a bit of room between the 7" wide plates and the burners. It was a slight mistake but it ends up working out well as it leaves some room between the flame and the burner mounts.
(12 count) 1 1/2" stainless bolts (M3 pitch)
(12 count) 1/4" aluminum spacers
(24 count) stainless fender washers
I went with two "Little Chugger" pumps from Ebay. They are like the march pumps but were cheaper due to a manufacturing flaw. I can't remember the exact cost but I think they were in the ballpark of $80-$90 each.
I just used a couple small plates with holes to mount the pumps to the frame.
For pump switches, I'm going to run a "double ended" extension cord from a GCFI outlet in my garage into a plastic shoe box mounted to the bottom of the frame. I'll have two remotes and receivers - one for each pump. I got the Skylink WS-100 from Amazon:
http://www.amazon.com/Skylink-WS-100N-Wireless-Control-Channel/dp/B00008X5D5/ref=sr_1_4?ie=UTF8&qid=1297129088&sr=8-4
Cost: ~$18.00 each
Three cans of Rustoleum High Heat flat black, again from Amazon:
http://www.amazon.com/Rust-Oleum-248903-Automotive-12-Ounce-Degree/dp/B003CT4AKC/ref=sr_1_1?ie=UTF8&s=hi&qid=1297129164&sr=8-1
Cost: $8.09 each
I'll let Paul post the pieces for the manifold, the yellow flex-gas lines, the brackets for holding the manifold to the stand and the parts that connect the lines to the burners. These last fittings were a pain in the butt to find. We ran 1/2" black gas piping, two T's one elbow, three valves, three short nipples... I think the manifolds were about $100.
I also dropped between $50 and $100 at the hardware store and the Depot on misc. crap like angle grinder brushes, stock steel pieces (straps and angle) both 14 gauge and 1 1/2".
Tools to have on hand:
Welder
Welding mask
Welding gloves
90 degree magnets
Vice grips or quick clamps
Wire Brush
Side cutter
Angle grinder (cutting wheels, grinding disks and knotted brushes)
Tape measure
Quick square
A marker or 3
Drill
Drill bits
*Hearing Protection
*Eye protection and a face mask