Search results

I used the 16.7 Cu ft Frigidaire FRU17G4JW full fridge for my project. I have it 95% done. I need to paint the front door and get a couple more lengths of CO2 line but other than that it is done. It holds 8 pin lock kegs and could likely hold 8 ball locks, 3 on the floor and 5 on the shelf. I...

Ok, thanks for the tutorial. Through the side it is.

Thanks for the info. Just for my own knowledge, why are the sides getting hot if there are no lines there? Or is it just that there are likely no lines where the shelf support inserts are?

Everything else matches the diagram, but this is the back, it is skinned in metal.

I’m Leary about going through the side because it got warm, but are you suggesting that the shelf supports should be ok? I’m not sure how to get the back skin off yet, but then I should be able to see how high up the condenser goes.

So I found a full size fridge for cheap and it looks like it will hold at least 6 pin lock kegs. I want to leave the CO2 tank on the outside to make it easier to pressure transfer and use my bottling gun and also leave more room inside for beer. I have a few candidate locations to drill into the...

I know that keezer’s are all the rage now, and ideally that’s what I’d like to do, but I live in a small house and don’t have the space. Does anyone have an idea on an ideal fridge size? I know there is a great resource for freezers but I can’t find anything on a fridge. I have a line on a 16.6...

I have a question on wiring. I have a 1000 and 1000+. The regular 1000 when it calls for heat or cool my LED lights I have wired in go on and stay on. I just wired a 1000+ and plugged in a floor lamp to test it, and when it calls for heat or cool both the LED i have wired in and the floor lamp...

Yes, that makes sense, the way they are now will work fine for me. My background is in agriculture and all the GPS and precision ag monitors go off like a Christmas tree crossed with an air raid siren when ever anything isn't completely right, so I was expecting these to be not as sophisticated...

So double check the Hy-1 and Hy-2, and then ramp up the temp past ALM-1 and I should get and alarm, and then let the water cool below ALM-2 and it should go off. That explains the intermittent working of the alarm. Just for my own knowledge why do the alarms only signal when it passes through...

Is that an original graphic, or can you share the source?

Not that I know of. Just two temperatures.

I have a Kal clone built from a kit, and I seem to have everything running properly except for the PID alarm. They are the Auber SYL-2352. The top number in red all read around 62*F, as I haven’t calibrated them to my Thermopen. The bottom number in green I can change and set. The elements fire...

I was hoping since it is a freezer with more cooling capacity then a fridge that I would get away with it. Might have to settle for two chambers and temps

I got a multi chamber fermentation chamber half built and just wanted a reality check before I proceeded further. The idea is that my dorm sized freezer will be set with a temp controller to around 2*C and then I will use an STC in the other 3 chambers to pull and push air from/to this cold 2*C...

Get 5 gallon pails and the sealing lids, I bought the same ones Kal recommends on his site http://www.theelectricbrewery.com/Gamma-Seal-lids

Anyone know of a supplier for the mister that ships to Canada? Or is anyone willing to order the 1/2” nipple and mister and ship to me up here? PM me please.

I enjoyed this novel as well, Smoke https://www.goodreads.com/book/show/27208482-smoke

Yes it does make sense, all the water flows through the 1/2” plumbing. Wasn’t sure if what the arrow was pointing to was a hose barb, but it is a filter. Thanks for clearing that up.