Electric Brewing Supply 30A BCS Giveaway - Last Weekend to Enter!


Home Brew Forums > Home Brewing Beer > Bottling/Kegging > keg dispensing trouble...
Reply
 
LinkBack Thread Tools
Old 06-07-2008, 06:33 PM   #1
HoppySatan
Feedback Score: 0 reviews
Recipes 
 
Join Date: May 2008
Location: S. Jersey
Posts: 39
Default keg dispensing trouble...

Hey all, I'm new to homebrewing and kegging. I have put 10psi on the keg and let it sit for a week. Chilled it and bled off down to a few psi and served. It seemed to pour best at 6psi. My problem is that it seems that the first pour is always foamy but flat. The next few pour ok i guess but it seems that the carbonation is gone within a few pours. If this is a problem of force carbing should I prime the next keg? Thanks in advance.

__________________
HoppySatan is offline
 
Reply With Quote Quick reply to this message
Old 06-07-2008, 06:36 PM   #2
EdWort
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
EdWort's Avatar
Recipes 
 
Join Date: Jul 2006
Location: Bee Cave, Texas
Posts: 11,967
Liked 266 Times on 139 Posts
Likes Given: 7

Default

Did you chill it before you put it on gas?

It needs to sit for a week at 39 degrees at 12 psi to carb properly.

EdWort is offline
 
Reply With Quote Quick reply to this message
Old 06-07-2008, 06:38 PM   #3
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
Vendor Ads 
Feedback Score: 2 reviews
 
Bobby_M's Avatar
Recipes 
 
Join Date: Aug 2006
Location: Whitehouse Station, NJ
Posts: 22,128
Liked 1029 Times on 685 Posts
Likes Given: 28

Default

10psi on a warm keg will do nothing no matter how long it sits. You'll need to chill the beer down and leave it at about 12psi/40F for 1-2 weeks. Your beer isn't going flat after a few pours, it IS flat and the foam you're seeing in the glass is not really from CO2 coming out of suspension. If you need to carb warm beer, it's going to take 30-40psi depending on the temp.

__________________
BrewHardware.com
Sightglass, Refractometer, Ball Valve, Weldless bulkhead, Thermometer, Decals, Stainless Steel Fittings, Compression Fittings, Camlock Quick Disconnects, Scale, RIMS tube, Plate Chiller, Chugger Pump, Super Clear Silicone Tubing, and more!

New Stuff?
Bobby_M is offline
 
Reply With Quote Quick reply to this message
Old 06-07-2008, 06:39 PM   #4
Blender
Feedback Score: 0 reviews
 
Blender's Avatar
Recipes 
 
Join Date: Jan 2006
Location: Santa Cruz, CA.
Posts: 3,116
Liked 5 Times on 4 Posts

Default

I would bet that it just needs more time. That has been my limited experience since kegging at the first of the year.

__________________

Gary

Blender is offline
 
Reply With Quote Quick reply to this message
Old 06-07-2008, 06:43 PM   #5
Sea
Green Flash IPA on tap
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
Sea's Avatar
Recipes 
 
Join Date: May 2007
Location: Southern Oregon
Posts: 1,479
Liked 5 Times on 5 Posts

Default

Read this:

http://www.northernbrewer.com/docume...ing-system.pdf


You shouldn't drop the pressure, 10 PSI is a good serving pressure if your lines are balanced. 6 PSI will cause your beer to go flat, unless it's very cold.

This all depends on beer temperature, CO2 PSI setting, and serving line size & length. 3/16 ID serving line has a pressure drop of 2 ft of head loss/ foot of line, so for a faom free pour, you need half your serving pressure in line length.

For instance: 12 PSI @ 40 deg F provides about 2.4 volumes of carbonation (very common volume for american ales). At this pressure, you will need 6 ft of 3/16 ID serving line for a foam free pour

__________________
I plan on living forever. So far, so good! - unknown.


Corrupt Brewers
Sea is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Dispensing Guinness on CO2 Elfmaze Bottling/Kegging 17 10-30-2009 02:12 PM
Dispensing Soda conpewter Bottling/Kegging 17 04-17-2009 12:36 AM
portable dispensing kit? kegeratorman1 Bottling/Kegging 4 10-18-2008 12:30 AM
Keg dispensing question JBrady Bottling/Kegging 2 09-03-2008 04:17 AM
Dispensing Problems ... Tanuvan Bottling/Kegging 4 03-28-2007 11:40 AM