Three vessel e-keggle bottom drain herms pics

[Jem]

My build like so many was inspired by Kal’s work and made a reality with P-J’s help along with countless others who shared and posted on this site, thank you.

Since there is an abundance of fantastic build threads, I won't go into detail and just share some pics.

 

[ChocolateMaltyBalls]

Very nice! I hope you'll share a pic of your rig in action, I'd like to see how you've got the control panel and pumps set up.

 

[Rivenin]

looking great!

 

[stubbornman]

It's glorious!!!1

 

[MidTNJasonF]

Very nice Jem.

I am building a bottom drain 3 vessel eHERMS system myself and have been on the fence about having them on a table/platform and having them stand independent with legs as you have. A couple of questions...

Do you find any stability issues with the kettles full?
Any reason you went with three points of contact/legs as opposed to four other than the cost of material and an extra caster?
Do you feel you might need to add any cross braces near the bottom of the legs to prevent leg flex?

 

[Jem]

Thanks for the complements.

Here's the control panel. Still playing with the timer. I need to get some of Bobby's labels, just haven't gotten around to it. Labeling the switches is a must when brewing with others.

Still looking for the best pump set up, this is my latest attempt. I did just read a post that its best to mount them with the head horizontally, I'm going to try that. Priming the pumps is a pain, especially when you need two.

 

[Bobby_M]

Right now you have the input on the high side and output on the bottom. That's probably the most challenging configuration you can put these heads in.

 

[Jem]

Very nice Jem.

I am building a bottom drain 3 vessel eHERMS system myself and have been on the fence about having them on a table/platform and having them stand independent with legs as you have. A couple of questions...

Do you find any stability issues with the kettles full?
Any reason you went with three points of contact/legs as opposed to four other than the cost of material and an extra caster?
Do you feel you might need to add any cross braces near the bottom of the legs to prevent leg flex?

Thanks.

I did try a couple versions of a table and couldn't find a setup I liked. I usually bring the keggles outside to clean them so the independent legs work great. I've seen some pretty cool clean in ace set ups but my brew area won't work for that, it's kinda small and no floor drain.

Having the keggles independent is nice for storage and smaller brewing areas.

I went with three legs for the cost of materials and ease of leveling, adding a fourth leg and bracing was a back up plan but it hasn't been necessary. They are pretty stable, especially when full, but I won't move them much if at all while in use. Attaching the legs at both the top and bottom keg skirts provides allot of stability.

Good luck

 

[Mdsutton]

It looks like like to opened from the bottom, and used the keg spout for the drain connection; correct? Did you cut out the old spout completely ;or just the top piece? Please give keg build details!
Looks awesome, I would like to make a mash tun from a keg I have and go RIMs.
Thanks,
Martin

 

[triskelion]

looks good, I'm planning a single keggle for biab very much like these. what element did you use?
I'm still not sure which elements are safe to use, I presume it would have to be copper or stainless steel, apparently chrome is carcinogenic.

 

[hustlebird]

looks good, I'm planning a single keggle for biab very much like these. what element did you use?
I'm still not sure which elements are safe to use, I presume it would have to be copper or stainless steel, apparently chrome is carcinogenic.

If its listed for use in a water heater it should be safe right? Since water heaters are food safe?

 

[BadNewsBrewery]

I (and many others) have been using the Camco elements for quite some time, and best I can tell I haven't died yet.

 

[jeffmeh]

I (and many others) have been using the Camco elements for quite some time, and best I can tell I haven't died yet.

Actually, if we wish to confuse correlation with causation, apparently ingesting the chemicals from the Camco elements has increased your knowledge of electric circuit design.

 

[Jem]

I'm using the 4500 camco ultra low watt elements, I initially used the standard curved 5500 elements but had trouble connecting them when I switched to a welded fitting and fixed electrical box.

 

[Jem]

It looks like like to opened from the bottom, and used the keg spout for the drain connection; correct? Did you cut out the old spout completely ;or just the top piece? Please give keg build details!
Looks awesome, I would like to make a mash tun from a keg I have and go RIMs.
Thanks,
Martin

Correct I opened up the bottom of the keg, I did not modify the keg spout at all, just removed the stem.

 

[GrantH]

For simplicities sake...holy balls!

 

[tre9er]

Right now you have the input on the high side and output on the bottom. That's probably the most challenging configuration you can put these heads in.

Pardon my ignorance, I don't have a pump, yet. But wouldn't the input on the high side mean liquid would flow down via gravity right into the head, thus priming it?

 

[tre9er]

Jem, I'd like to see pics of the HLT inside and also your whirlpool setup in the BK. THanks in advance.

 

[Jem]

looks good, I'm planning a single keggle for biab very much like these. what element did you use?
I'm still not sure which elements are safe to use, I presume it would have to be copper or stainless steel, apparently chrome is carcinogenic.

Forgot to mention I have used the boil keggle for brew in a bag, it worked nicely. I have since put together a ebiab set up using a stainless steel pot. If you're doing exclusive biab you might consider a kettle having smooth sides when you pull the bag outweigh the bottom drain for me. Just a thought.

 

[Jem]

Jem, I'd like to see pics of the HLT inside and also your whirlpool setup in the BK. THanks in advance.

Here's pics of both I happen to have on my phone.


My coiling of the ss tubing was not as clean as would have liked, my suggesting to anyone considering a ss coil is to buy a ss immersion chiller and modify it to work.

 

[jeffmeh]

Pardon my ignorance, I don't have a pump, yet. But wouldn't the input on the high side mean liquid would flow down via gravity right into the head, thus priming it?

The basic challenge to priming the pump is that the air in the pump must be displaced by the liquid. If gravity cannot overcome the air pressure, the pump will not prime. So if the inflow is directly above, and the outflow is directly below, it can be difficult for the liquid to overcome the air because the air is an opposing force. Having the inflow lower than the outflow better enables the air to escape, so the liquid can fill the pump. Once the liquid fills the pump, the pump itself should be able to overcome the remaining air.

That's the gist of it. Some people use bleeder valves to make it even easier for the air to escape, but the basic configuration of outflow higher than inflow is the recommended approach, regardless.

 

[FlyDoctor]

Right now you have the input on the high side and output on the bottom. That's probably the most challenging configuration you can put these heads in.

What do you mean Bobby?

 

[jeffmeh]

What do you mean Bobby?

I certainly welcome Bobby chiming in, but I tried to explain it in the post above yours.

 

[tre9er]

The basic challenge to priming the pump is that the air in the pump must be displaced by the liquid. If gravity cannot overcome the air pressure, the pump will not prime. So if the inflow is directly above, and the outflow is directly below, it can be difficult for the liquid to overcome the air because the air is an opposing force. Having the inflow lower than the outflow better enables the air to escape, so the liquid can fill the pump. Once the liquid fills the pump, the pump itself should be able to overcome the remaining air.

That's the gist of it. Some people use bleeder valves to make it even easier for the air to escape, but the basic configuration of outflow higher than inflow is the recommended approach, regardless.

Excellent info, thanks. I have a pump on order right now and just assumed I'd put the input above output. I may mount it "upside down" now based on this info.

 

[FlyDoctor]

I certainly welcome Bobby chiming in, but I tried to explain it in the post above yours.

Whoops - sorry - I should read the whole thread first.

Sweet set-up!

 

[BadNewsBrewery]

Regarding the pump setup - the issue I've seen is not the initial prime - as the liquid flows out of your kettle and through the pump and then back out the discharge of the pump, it will clear most, if not all the air. The issue is air pockets - any bubbles that get sucked into the pump, or any cavitation, anything that causes air to enter the pump head will not clear. The bubbles will try to go "up", while the liquid is flowing "down", and basically you'll have stuck bubbles. If you have the discharge as the high point, any and all remaining bubbles will want to go in the same direction as the flowing liquid and the pump will run better and happier. Because pumps have feelings, too.

 

[Jem]

Great info on the pump setup, wish I would have posted my build earlier

As soon as I have a few minutes I'm going to test the repositioned set up.

Thanks

 

[jeffmeh]

Regarding the pump setup - the issue I've seen is not the initial prime - as the liquid flows out of your kettle and through the pump and then back out the discharge of the pump, it will clear most, if not all the air. The issue is air pockets - any bubbles that get sucked into the pump, or any cavitation, anything that causes air to enter the pump head will not clear. The bubbles will try to go "up", while the liquid is flowing "down", and basically you'll have stuck bubbles. If you have the discharge as the high point, any and all remaining bubbles will want to go in the same direction as the flowing liquid and the pump will run better and happier. Because pumps have feelings, too.

Good point, although I have seen failure to prime also.

Off-topic, but when I rack to keg after a 33F cold crash, at about 65F ambient temperature, I encounter a similar physical phenomenon. The CO2 comes out of solution and rises, opposing the gravitational force acting on the liquid, resulting in slower racking.

 

[wdevauld]

What do you do for separating hops and hot break from the wert? I see you have a setup to allow for whirlpooling but is that not opposite if what you want with a center drain?

 

[tre9er]

What do you do for separating hops and hot break from the wert? I see you have a setup to allow for whirlpooling but is that not opposite if what you want with a center drain?

Pretty sure his center drain is for CIP (clean in place). That allows you to rinse, scrub, etc. and everything just drains out the bottom, like your bathtub, without having to tip the vessel over, etc.