Retro Kegerator

[pmd5700]

I noticed a few retro style mini fridges. I've tried searching around and can't really find anyone that's used any of these. I don't want to order one if I can't fit 2 kegs in them. I'd feel most safe with the Danby one since I know other models have been used regularly. The Galanz one clearly has the ability to use the full vertical space; I'd just be concerned with the footprint in front of the compressor bump to fit two kegs.

Has anyone used any of these before? OR does anyone know if any other retro looking options for a Kegerator/Keezer?

https://www.homedepot.com/p/Galanz-...e-Door-Fridge-Only-in-Red-GLR44RDER/308105328

https://www.homedepot.com/p/DAEWOO-...ge-in-White-with-Freezer-FR-044RCNW/310154607

https://www.amazon.com/Danby-DAR044A6PDB-Contemporary-Refrigerator-Metallic/dp/B01FIQ67B6

 

[odie]

I like the retro galanz too...been looking at it but they are not in stock for me to directly measure. my gut instinct says they will fit 2 kegs with minimal modifications.

 

[odie]

I'm building an older GE 4.4 I have to cut the side shelf support slots and the door liner out.

 

[RoguePixels]

If you're able to see any of these in store before you buy, you could cut out some cardboard circles the same diameter as your keg and see how they fit in the display model.

 

[odie]

Doesn’t really work since the shelf slots protrude inward. I’ve found many 4.4/4.5 class fridges that I can fit 2 corneys into the bottom but not mid-waist

 

[odie]

The one I bought fit 2 on first but after I got it home and folded the freezer plate down to fit the kegs the sides were too narrow. So I had to cut out the shelf slots

 

[pmd5700]

I like the retro galanz too...been looking at it but they are not in stock for me to directly measure. my gut instinct says they will fit 2 kegs with minimal modifications.

I'm almost wondering if I should buy one of them and get some measurements before I do anywork. Home Depot is usually pretty good about returns. It'll just be a hassle to transport it.

If you're able to see any of these in store before you buy, you could cut out some cardboard circles the same diameter as your keg and see how they fit in the display model.

It doesn't look like any stores near me have them.

The one I bought fit 2 on first but after I got it home and folded the freezer plate down to fit the kegs the sides were too narrow. So I had to cut out the shelf slots

How hard was it to cut the shelf slots? Did you just use something like a Dremel and then seal up the cuts?

 

[odie]

I use a "multi-tool" I think it's called. those vibrating tools with a serrated blade...Harbor Freight...useful for plunge cuts, drywall, tight spaces, you name it... https://www.harborfreight.com/variable-speed-oscillating-multi-tool-63113.html

I just shaved down the side protrusions and 2 kegs slipped right in. The cardboard cutout thing doesn't reveal these issues too well. nothing like using a real keg to test fit fridges and freezers.

There are several brands & models of 4.4/4.5 class fridges out there...the key seems to be finding on with a with of greater than 20" if you have hope of not modifying the sides. Depending on the design of door liner you may or may not have to cut or remove it.

The door liners if they are too big can be replaced and saved rather than cut. Home Depot and Lowes sell large flat sheets of various plastic materials...trace out your old liner and cut a new flat one, thus saving your liner for the future if you decide later to undo everything. You can't simply just remove the liner and be good. the liner actually helps the gasket seat properly. So it's either cut the liner to fit kegs or replace with a flat sheet.

 

[firerat]

The door liners if they are too big can be replaced and saved rather than cut. Home Depot and Lowes sell large flat sheets of various plastic materials...trace out your old liner and cut a new flat one, thus saving your liner for the future if you decide later to undo everything. You can't simply just remove the liner and be good. the liner actually helps the gasket seat properly. So it's either cut the liner to fit kegs or replace with a flat sheet.

That's a damn good idea. Do you know how many mini fridge doors I've shaved down and never thought of doing it this way? Too many. LOL

 

[pmd5700]

I use a "multi-tool" I think it's called. those vibrating tools with a serrated blade...Harbor Freight...useful for plunge cuts, drywall, tight spaces, you name it... https://www.harborfreight.com/variable-speed-oscillating-multi-tool-63113.html

I just shaved down the side protrusions and 2 kegs slipped right in. The cardboard cutout thing doesn't reveal these issues too well. nothing like using a real keg to test fit fridges and freezers.

There are several brands & models of 4.4/4.5 class fridges out there...the key seems to be finding on with a with of greater than 20" if you have hope of not modifying the sides. Depending on the design of door liner you may or may not have to cut or remove it.

The door liners if they are too big can be replaced and saved rather than cut. Home Depot and Lowes sell large flat sheets of various plastic materials...trace out your old liner and cut a new flat one, thus saving your liner for the future if you decide later to undo everything. You can't simply just remove the liner and be good. the liner actually helps the gasket seat properly. So it's either cut the liner to fit kegs or replace with a flat sheet.

That's a damn good idea. Do you know how many mini fridge doors I've shaved down and never thought of doing it this way? Too many. LOL

I saw a picture floating around (maybe here?) that showed someone that put a decorative cover after they removed the panel. It looked almost like wallpaper!

 

[odie]

I think it was something like this...not hard plastic but soft and easily workable.

https://www.homedepot.com/p/1-16-in-x-4-ft-x-8-ft-Plastic-Panel-63003/202090190