Search results

Cleaning out more stuff and have a 809HS win a bronze head available. I pickled it a while back to remove the surface lead (not that therewas enough to worry about California). I had it mounted Ina toolbox as it has no foot but other than that it was a great little pump. $110 plus $10 shipping...

Going through some stuff that I don't think I will be needing anytime soon and realizing I have hoarded too much stainless. I have four 2" inoxpa brand and two 1.5" Alfa laval tri clover sanitary butterfly valves. $40 for the 1.5" $45 for the 2". $5 shipping for 1-2 $10 for 3+.

I have changed plans on my fermenters and don't need my 1" valves any more. They are 1" sanitary size which is a 1" port size that mates up to a 1.5" TC ferrule. They have been used, but are in great shape and all have good seats. Seats are either epdm or silicone. I can get actual photos...

Does anyone know what I could use for speed control for one of these EC motors? I don't think the cheap digital pwm speed controls are appropriate for an EC motor, but do t know what else to look for. All the EC motors I've dealt with had a speed input separate from the power. Will 12-28v power...

Hello, I have changed out some of my fittings to 3/4" and have some tri clamp barb and female threaded adapters for sale. (5) - 1/2" fpt 1.5"triclamp adapter $9 ea https://www.brewershardware.com/1.5-Tri-Clover-X-1-2-Female-BSPP.html (8) - 1/2" barb 1.5"triclamp adapter $8 ea...

I have a few spare 15' 10/3 30A extension cords that I won't be using for my e panel build that can be used for connecting your panel to the wall receptacle or element cords between your panel and kettle. These are three wire SOOW type cord and have locking L6-30 male and female plugs on them...

Hello, I have some 2013 whole leaf hops that didn't get picked up by club members from a club buy I did. They are all from Hop Union through Country Malt Group. I received them, broke them down into 1# and 1/2# foodsaver vac bags, and what was left over has been in a chest freezer since then. I...

I think there are some Rheem elements out there that are copper with a brass thread, but was perusing ebay and came across these guys...

I have a few 1/2" Apollo & 1/4" Milwaukee threaded stainless ball valves for sale. They were used in compressed air, nitrogen, and vacuum service and are all in great shape. $8 each plus shipping. Quite a few should fit in a small flat rate box. I also have a few spare handles and nuts...

Hello, I have some extra 2013 whole leaf hops that didn't get picked up by club members from a club buy I did. They are all from Hop Union through Country Malt Group. I received them a few weeks ago, broke them down into 1# and 1/2# foodsaver vac bags and what was left over has been in a...

I have my triplets for sale. They are March 5ss series pumps and are one of the best pumps I have ever used for brewing. They throttle from a trickle to full bore and will whirlpool my 100qt boil kettle with ease. FDA compliant and good to 250* so these are for the serious homebrewer or...

I have a set of digital amp and volt meters complete with the shunt and 5v power supplies similar to Kals Electric Brewery meters $50 shipped Cutler Hammer three position momentary switches $10 ea Plus Shipping Cutler Hammer three position maintained switches Terminals on these are a...

Hello everyone, I have a 20 plate brazed plate chiller I am no longer using. It is a commercial ITT exchanger made just down the road here in Buffalo NY. 3" wide x 8" tall x 3" high including the 3/4" male threaded connections. It would chill a 10 gallon batch down in under 15 minutes with...

I have a few parts kicking around that I'm not currently using. Standard 1/2"-3/4" clamps just like what sabco uses on their Brew Magic and others for diptubes or any other 1/2" or 3/4" tri clamp piping. Various brands $5 each 2"MPTx2.5" TC adapter for the bottom of a poly...

Hello everyone, I have a few spare pumps available that I am no longer using or need as spares. They are Little giant HC series pumps which are pressure tested to 200* and have worked fine at boiling temps for myself and many others. The 3-MD-MT-HC is the same pump Sabco used on their Brew...

http://www.ebay.com/itm/231016510373?ssPageName=STRK:MEBOFFX:IT&_trksid=p3984.m1432.l2649 I threw out n offer of $20 and he countered with $50, but there might be more bargaining to be had. Either way $70 for a big ole heatstick is a pretty good deal.

I wanted to do something different besides transferring my harvested yeast from my sight glass or triclover spool so I made up an adapter for a mason jar. It is basically a ss disk that I drilled out with a hole saw and then punched out a 1.5" hole. Then silver soldered a triclover ferrule...

I had a toolbox caddy, but it was cumbersome and I wanted a bit better layout of my stuff. I also separated my rims equipment from my chilling equipment since we were fighting for equipment when we were doing multiple batches at one time. Previous toolbox caddy New caddy Detail of the...

I've been looking for an enclosure for my rims element and looked at a few of the ones that people have done on here and other sites. I like the all stainless version and may get there some day, but for now here is what I've came up with. I started with a 1/2" conduit LB and 1/2"...

I've got a few spare 1/2" npt x 1/2" brass compression 90's that I used for sightglasses. No tube, but I will send 3 o-rings and the brass ferrule so you can choose if you want a permanent or removable connection on the tube. $5 each plus whatever shipping ends up being...