Search results

never done a decoction mash but I only ever pressure ferment at around 16psi, I recently had a stuck ferment when the temperature dropped to 6 degrees C, the yeast is under stress and needs higher temperature. my only solution was to put more yeast in plus additional nutrient and pushed up the...

thanks @mper will have to do my homework on jtag as I haven't had issues with it on the 1.4 version, I haven't had the LED activated on any of the super minis I have programmed so far and version 1.4 worked with gpio6 and 7 but not on version 2 so somehow jtag must have been activated and...

hi @mper does this mean that jtag is automatically enabled on the current version? I have been using gpio6 and 7 for my i2c comms as pin 8 is the blue led which I would like to work as it gives me an indication of the state of the system. I am still not sure where to find the pin definition for...

hi @mperi have designed a pcb to take the ESP32C3 super mini form factor module (I am busy making it a shared project on pcbway), there are 2 problems, 1) I still need to get the blue led working looks like I may have to create a separate environment for this as the normal C3 has a multi colour...

yes it displays the ip address but if I try to log into the web page it is just a blank unreachable that I get, I can ping it ok

hi I have tried to make this device, I have tried to get it working a good number of times with my green tab 1.7 inch display on a nodemcu v3 without much success, I get the display with the two dummy ispindel devices cycling but there is no display on the web interface, it reports connection to...

I hate waste, always left with 3 litres in the bottom of my boiler, just throw it in a jug and strain through a very fine bag, nothing wasted and very little trub material in the fermenter

if this in response to my magnetic reset, it it's not a power on off switch but a way to reset the device and force it into configuration mode when it goes to sleep, a bit lighter than a glass reed switch but definitely a bit more complicated. just another option for anyone interested.

I have managed to fit an ispindel inside a rapt pill housing, In south Africa the ispindel housing is difficult to get whilst the rapt pill is easy, I purchased 5 cherry Phillips v3.2 boards and reshaped them, just got enough off either side to fit them in the housing without damaging any tracks...

this is my magnetic charging device, I considered it essential addition for the use of a rapt pill housing as they are difficult to open and close, wether it is useful or adaptable to a ispindel tube I don't know as I haven't got one to test. the rapt pill does have a magnetic charging unit of...

the link to the coil purchased on aliexpress, there are a few similar ones with either 4.2V or 5V single outputs available but as yet this is the only one I have used. charging receiver coil dual output [lithium battery wireless charging] 5W wireless charging receiver module small coil...

this is my magnetic charging device, I considered it essential addition for the use of a rapt pill housing as they are difficult to open and close, wether it is useful or adaptable to a ispindel tube I don't know as I haven't got one to test. the rapt pill does have a magnetic charging unit of...

here are the aliexpress links to the components I used. hall effect switch （5PCS）DRV5032FADBZR DRV DRV5032 DRV5032FA DRV5032FADB DRV5032FADBZ 100% Brand New Original IC SOT23-3 https://a.aliexpress.com/_EJuDtqr schottky diode 100PCS MBR0520T1G MBR0530T1G MBR0540T1G SOD-123 MBR0520 MBR0530...

here is my build for the magnetic reset, I used a drv5032FA which is push pull, a drv5032FC is open drain and more suitable if available but this worked for me with a schottky diode in series with the output to prevent loading the device with reset and wake-up. I mounted the device on a sop...

hi @mper a build for the esp32 c3 would be of great help for me as I build my unit for this device. is the setup for the ispindel in the push settings? what format do I need for it? I have lots of experience in board and circuit design but networking is not a strong point for me.

I am busy building a couple of Ispindels one with a esp32 c3 super mini (waiting on pcbs) in a prototype at the moment, the other in an esp8266 d1 mini on a v3.2 cherry Phillips board which I managed to whittle down to fit in a rapt pill container, as they are tight to open and close I have also...

sorry they are 1Amp rectifiers so would only allow one half of the power through.

another option is to put a 1n4005 or 1n4007 in series with the belt wired into the plug will halve the power

1 joining this forum (picked up so many useful tips) 2 RO water and salt additions 3 vorlauf, this addition to my lautering process improved my extract efficiency by 10 percent 4 whirlpooling helped improve my pour of the trub for clearer wort 5 pressure fermentation, no need to worry about...

Hi @pocketmon I am trying to get this project working on an ESP32-2432S028R device, it loads fine and I can communicate via the web interface but the display doesn't come on, is there something I need to do in the platformio.ini file? I expected it to work with the original settings as the...