New regulator/burner test - Home Brew Forums

Register Now!
Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > New regulator/burner test

Reply
 
Thread Tools
Old 01-12-2009, 05:30 PM   #1
hammer one
 
hammer one's Avatar
Recipes 
 
Jan 2008
Posts: 292


Just hooked up the new propane regulator it is adjustable from 0-60 and it was only $19.95 from Tractor supply. I wish I would of got this sooner. The best $20.00 upgrade ever. The burner that I'm using is a high pressure from Acadamey sporting goods $11.99 a great deal when you don't have to pay shipping. There will be 2 more of these burners going on the new 10gal system. Here's a few pics of what I got.


 
Reply With Quote
Old 01-12-2009, 05:55 PM   #2
MajorWoody
Recipes 
 
Dec 2008
Portland, OR
Posts: 60
Liked 1 Times on 1 Posts


Is that the Mr. Heater reg? You will like that one, I have it on my potato cannon. It does a great job of maintaining a constant pressure as the tank empties.

 
Reply With Quote
Old 01-12-2009, 06:10 PM   #3
hammer one
 
hammer one's Avatar
Recipes 
 
Jan 2008
Posts: 292

Mr Heater it is! This thing really kicks ass. I'm going to have to watch it.

 
Reply With Quote
Old 01-12-2009, 06:52 PM   #4
aekdbbop
 
aekdbbop's Avatar
Recipes 
 
Sep 2006
Nashville, TN
Posts: 2,645
Liked 8 Times on 7 Posts


what exactly does this do for ya?

 
Reply With Quote
Old 01-12-2009, 07:36 PM   #5
hammer one
 
hammer one's Avatar
Recipes 
 
Jan 2008
Posts: 292

Changing from low pressure to high pressure should decrease my time to bring wort to a boil and water to temp. With the adjustable regulator I will be able to fine tune the flame. I don't know if it will help save fuel but it will help with time.

 
Reply With Quote
Old 01-12-2009, 09:18 PM   #6
ScubaSteve
HBT_SUPPORTER.png
 
ScubaSteve's Avatar
Recipes 
 
May 2007
New Bern, NC
Posts: 3,677
Liked 83 Times on 57 Posts


What kind of burners are you using? You could probably use that one reg to supply all three burners, as long as you're using a manifold. It's kinda cool to see the flame blast out on high....but be careful not to let the flame blow itself out. I recently souped up my reg from 10 PSI to 20 PSI and found that the burners would go out because the pressure was too high (in so called hi-pressure SQ14 burners). Needless to say, just a minute of unlit propane blasting from the burner could really create a dangerous situation; even in a garage with the door open.

The good news is the reg is 0-60, so it will work with any burner. I wonder though.....what would possibly use 60 PSI??? A furnace?

 
Reply With Quote
Old 01-12-2009, 11:21 PM   #7
hammer one
 
hammer one's Avatar
Recipes 
 
Jan 2008
Posts: 292

The way I'm planning on setting this up is to have a needle valve before each burner. I'm going to put high pressure burners on the HLT and Kettle, I"m not shure if I should put a low pressure burner on the MLT.......I'm thinking mabey so because its just to maintain heat. What do you think? Look in my gallery thats the high pressure burner I'm talking about.


 
Reply With Quote
Reply
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Urgent! Propane Burner Regulator Leak! Help! ISUBrew79 Equipment/Sanitation 2 08-16-2008 06:31 PM
High or low pressure regulator for this jet burner? HarvInSTL Equipment/Sanitation 1 03-28-2008 07:06 PM
New burner or upgrade regulator? Didymus Equipment/Sanitation 22 12-03-2007 07:10 PM
Second test drive on my burner Jim Karr Equipment/Sanitation 8 05-02-2007 12:20 PM
Test drove my burner Jim Karr Equipment/Sanitation 14 04-18-2007 11:42 AM


Forum Jump