Search results

Used, but in great condition and fully functional, Speidel Braumeister 20L system. This system is fully electric and automates the process from heating the strike water, to regulating the heat during the mash (you can even program step mashes!), right up to the start of the boil. I have had so...

3 of my buds and I rented a cabin on the Russian River near Guerneville in mid-August. We plan on hitting the breweries, but I'd love recommendations for good eats and good places to get a wide selection of CA brews, both on draft and in bottles to take home. Last post I could find was from...

So, I realize there's already a tradition of putting together Randy Mosher's 12 Beers of Christmas. However, I was wondering this morning if I could come up with beers to represent the song lyrics. Here's my brainstorm: Partridge in a Pear Tree (Pear Cider) Turtle Doves (choco, caramel, pecan...

Hello, Fellow HBTers! The Winter Ale Festival is a third party benefit for the ALS Association. Our private event is a celebration of the Holiday Season and the giving spirit that encompasses this time of year. This year's event is 21 and over and will be held at the Milwaukie Center on...

Hello, Fellow HBTers! The Winter Ale Festival is a third party benefit for the ALS Association. Our private event is a celebration of the Holiday Season and the giving spirit that encompasses this time of year. This year's event is 21 and over and will be held at the Milwaukie Center on...

So, I built an eKeggle with a 240V 5500W element controlled by an Auber 2352. 3 batches in and I love it! However, I'm starting to think about small batch eBIAB, but only if I don't have to make a whole new controller. So, here's the thing: my old propane rig has a 7.5gal kettle, but it's only...

I've got my Auber 2352 setup and am "brewing" water for the initial test. I'll do a better write up after this weekend's brew. First, a question: If I set my Al1 to 170, as well as my SV, will the alarm go off during autotune, or are alarms disabled during autotune?

I'm trying to wire up my alarm disable switch, the SW2 from Auber. I'm following this diagram from P-J: But the back of the switch looks like this: So how do I match up what P-J shows in the diagram with what I see on the switch?

I'm at the tail end of my build: wiring components in the control box. I have the Auber project box (Pbox16), the 40A SSR, and the Auber heatsink. Can I avoid cutting the back panel and just sandwich it with the SSR on the inside and the heatsink on the outside? Does that still give the same...

So, my goal is to get to the baseline listed in the primer. Below are my recent numbers from our water dept. what do I need to do to just reach the baseline? Will one of those DIY cartridge filter setups work? Do I need to cut with RO? Sodium 10 6.5 Calcium...

As you can see from the picture, my welder did an amazing job of cutting the lip away completely. Of course, I forgot I would need a bit of a lip to rest a lid on. D'oh! What do all of you suggest? I was thinking of maybe installing some brackets, or even just bolts where I want the lid to...

I'm getting 30A 240V added to my garage this month. Which NEMA wall receptacle should I get installed? I plan to feed my controller via the HD spa panel.

I've seen lots of references to this diagram for single PID, single element: But i'd like to add a flashing buzzer attached to the PID alarm and simple switch to turn off the buzzer, like in this photo: Can someone find this diagram? I also need a part number for the switch. Thanks to...

So, recently I've started thinking about switching directions from a 3 Keggle HERMs to a single Keggle BIAB. I've got some questions: 1. Has anyone found a basket that works well in keggles? 2. Will a whirlpool/recirc valve at the top of the Keggle, similar to Kal's, get in the way of the...

So, I asked some buddies of mine that subscribe to BYO if they got a card and they didn't. Does every subscriber get one? Is it random? Do you have to be a longtime subscriber? What's the deal?

Of COURSE, I didn't save the threads with the diagrams and parts lists for the system I want to build! :) Can anyone help link to the right ones? I know they're out there already, I'm just having a little difficulty finding them through search. I'm planning on a 30A 220V 5500W HERMS system. 3...

I'm getting my kegs cut, punched, and welded this week, so I can actually start realizing my plan of going electric! Here comes the string of questions! I'm planning a single PID, single pump, single tier, three keggle HERMS system. It's a scaled-down Kal setup, basically. This question is...