Search results

Built my homebrew setup back in 2014 and recently the house got struck by lightning. Only thing (for the brewery) I had to replace was the Aubur SYL-2362. I got it wired up the same way, but cannot for the life of me remember any of the settings, and I don't think the temperature probe is...

I've had a Love TSS2 for several years and recently it started throwing a shorted probe error. I unplugged the one that was causing the issue, but now the other probe reads low into the negatives (between -16 to -32) when I have it set at 27, but the inside temp is no where near that cold. If I...

I know this is a few months old, but I wonder what the efficiency differences are with this method?

Does anyone have a recipe for Boulevard Bob's 47 Oktoberfest? I had this the other day and thought it was amazing, would love to brew it. http://www.boulevard.com/BoulevardBeers/bobs-47-oktoberfest/

I used the miracle grow premix stuff from lowes with a bunch of top soil mixed in. You think it needs more fertilizer? Nitrogen or just a mixture?

http://imgur.com/a/x4HuL Can anyone help identify what may be going wrong with my hops? I noticed the damage this morning, and don't know what caused it. I also noticed a ton of little mushroom blooms. These were not present when I checked 2 days ago. I am using raw bailing wire for my...

Thanks Hunter. I will be doing auto tune tomorrow night, but can you share all your others 2362 settings? Here is what it looks like now. Everything is leak tested and ready for first heat test after work tomorrow. After this project is done I will be installing a sink and SS table. Sent...

Leak test on vessel #1 IMG]http://i.imgur.com/VZcme5b.jpg[/IMG] Sent from my iPhone using Home Brew

Planning on installing the elements today and leak testing. Hope all goes well. I'll be using brewhardware.com enclosures. Sent from my iPhone using Home Brew

Just checked some electrical codes and it's fine as I'm using 10g for the shared. Sent from my iPhone using Home Brew

Hmmm. Not sure I understand the need. Grounds are shared all the time. Sent from my iPhone using Home Brew

Yes all wires connect to the box and the lid as well. The box is then connected to the power input ground which runs back to a gfci protected outlet. Sent from my iPhone using Home Brew

Alrighty. Got a lot of work done. Drilled holes in both keggles. Had some requests for some wiring pics. With this small of an enclosure it's hard to make "nice'wiring runs, but I did the best I could. This is where I tightened the nut to the post too much and it came off. Had to...

I am planning on placing my element opposite my valve and dip tube on my keggle with the hopes that the 5500W Ripple element will bend around the dip tube. I'm wondering though how high I need to place it, the lower the better right? Especially if I want to do some 5 gallon batches. But I've...

This buzzer, http://www.auberins.com/index.php?main_page=product_info&cPath=7_33&products_id=215

The Alarm is wired to the PID and the Timer. I use those two switches on either side of my buzzer to turn on/off the PID or Timer alarm. Here is the wiring diagram. I did it the exact same, except the Green 220v led is wired different and I used a different timer, so the numbers on mine were...

That's a good idea if you don't require the ability to disconnect the cables. The receptacles do take up a lot of room. The ground posts are larger than the circular connectors so I used split spades, but it was difficult to wire multiple onto one post. I brought all my grounds to a wire nut...

@Woodbrews. Since you only have 1 grounding stud to work with now be VERY careful on how tight you put that nut on. I over tightened on one of the studs and it broke off, luckily there was the 2nd one in the box. Looking back I wish I would have gotten a larger box, but the convenience of...

Hi Rick. After doing auto-tune did you change any settings manually? I'm trying to set mine up now too.

Yeah I think Kals is based on the 2352 which had completely different menus and setting parameters. I've been reading Aubers instruction manual, but I'm lost in translation lol.