Search results

I have an Anvil Foundry which I was using at 240v at my previous residence. I have recently moved to a new apartment. The stove is gas so I can't use that. From what I can tell the only outlet > 120v is the dryer outlet. It uses this cord, 4" 30 AMP 3 Wire Dryer Cord|^|WX9X2. I bought this...

I recently moved to a new apartment. Previously I would remove the aerator from the faucet and connect a male quick disconnect. I would connect the immersion chiller to this to cool and also fill my brewing vessel. The faucet is much nicer, but does not have the regular aerator to replace...

sold

I am planning on welding a brew stand sometime soon. It will be used to brew 5 gallon batches. I’m currently using 3 converted keggles. Is 2 inch square 14 gauge steel sufficient for this? It’s possible I will do some 10 gallon batches. I may also purchase 20-25 gallon pots.

I am trying to figure out how to mount the Brew Pi Spark 3. I bought a cutting 12x18 cutting board, which I would like to mount it to. I noticed there’s 2 holes on the back, is this for for mounting the device? Also what is the MicroSD slot used for?

I am planning on making a cyser. I was wondering what amount of tart cherry concentrate equals 5 lbs of tart cherries.

I am wiring a drum switch to control the motor for my grain mill. The switch is Dayton 2x440 and the motor is All American Ale Works Power Grinder. The following are the motor and switch wiring diagrams, followed by what I think is the correct way to wire this. Are there any problems with...

I bottled a Belgian Dark Strong 4 weeks ago, that is still showing no signs of carbonation. The yeast I used to ferment was WLP530 Abbey Ale Yeast. I also added a vial of WLP530 along with corn sugar to the bottling bucket. The amount of corn sugar I added was enough to carbonate around 2.3...

I bought a 2'x3' stainless steel table to use to mount my motor and grain mill. It has a support underneath the center of the table. This is where I am planning on mounting the motor and mill. Would removing a six inch section of the support be a bad idea? I would need to remove it for the...

Does anyone have any experience with RVA Yeast Labs LLC? The company is a 2 hour drive from where I live. Plus they include 2 billion yeast in their bottles.

I purchased an Power Grind motor recently. Just want to make sure I am following the directions correctly. This is what is included:

Whenever I try to pump water or wort when it is boiling there is cavitation. I have tried pumping the liquid well before it reaches boiling, but as soon as it is boiling the problem starts. I have tried reducing the flow after the pump but this hasn't helped. Is there any way to prevent this?

I finished wiring my panel, and checking all wires. The 5 amp fuse is blowing whenever I hit the power button. Any ideas what would cause this? The schematic I used is below. The old, incorrect schematic was removed to not cause confusion. The correct one is here.

I am finishing my control panel. I am using this relay. I want to make sure if I have wired this correctly. Here is a picture of what I have done. The diagram I am using is at the bottom

I need to cut two 44mm holes for the pid and timer I will use for my control panel. I bought this encloser http://www.ebay.com/itm/NEW-12x12x8-300x300x200-ENCLOSURE-WITH-BACK-PLATE-INDOOR-OUTDOOR-/110926323924 What would be the best method to cut the square holes? For the heat sink I drilled...

I just made my first sake using the directions and ingredients from www.homebrewsake.com. It turned out good, but it does have a slight yeasty/moldy/funky taste. Is this normal? If it is not normal, what can I do to help prevent this in my next sake?

I started using a plate chiller for my last 2 batches. The chiller has been leaking from the water in connection. I used plumbing tape on the threads, but this didn't help. I have been turning the water on all the way. Should I be reducing the flow of water going in, or is the chiller defective?

Has anyone built a kegerator using the Danby Designer DAR044A1BDD? Its the newer model of the Danby DAR440BL.

Based off of this diagram I would like to create a control box for my rims tube element and 2 pumps. I am confused about how to add the 2nd pump and control switch for the second pump. So far my parts list is: 2 x Terminal Strips (4 pole) 1 x Terminal Strips (5 pole) 1 x jumper 1 x...

I have a Cornelius Plug Adapter-1/4" FFL x 19/32" and wish to connect a 1/4" barbed adapter to it. I have tried both a 1/4" mpt barbed adapter and a 1/4" mfl barbed adapter. The 1/4" mpt threaded adapter will screw in a little but not enough to be secure. Anyone have any ideas on what to use?