Search results

Will starsan foam too much with this??? Vinator Bottle Rinser

I am looking to build a fermentation chamber and found a really good deal on this. I was going to use this acrylic (plexi-glass) as the inside bottom over my insulation board so that it would be easy to clean up any spills. I found this used sheet for 10% of what 1/4" would cost. The chamber is...

I finally have time to brew this weekend, kind of. I have a soccer game in the middle of a six hour gap. Can I mash for the 2 hours I am at the soccer game, then finish the brew day when I get home? It is a Heff and I plan on mashing at 154* Also, do you recomend mashing at 150* or 154* for...

Two kegs for sale here in Fullerton CA. Email me at: [email protected]

Does anyone know? I have about 10 people to split grain with. how much does a 2,000lb pallet cost? That is the amount that BULK comes in right?

So, I am trying to drill a hole in my keg with a step bit. These are the $10 step bits from harbor freight. The first 3 steps went fine, but now I am at about 1/2 inch and it doesnt cut. It just spins and smoke (thats when I stop). Is there a trick to using these bits?

So, I have quite a few large events coming up in the summer (wedding, camping trips, etc...) and would like to start stock piling the beer now. However, I do not have a temp controled area to store more than 2 cases. At the liquor store they have beer not in the fridge, is this ok for homebrew...

Found this co2 tank by my house. But when does it need to be retested? http://orangecounty.craigslist.org/spo/1668359663.html

I want to buy a wort chiller (immerson), what is the best to go with? I know that a steel one is stronger, but a copper chills better. How much better does copper chill? I want to chill 10 gallons, and looking to brew once or twice a week. (Sharing the equipment with people.)

So, I am going to plumb my brew rig with some black iron pipe. Is there a special ball valve for gas, or will the brass ones that people use on the brew pot work fine? This will be high pressure propane.

Ok, I was set on building a 3 tier rig. However, now I am thinking about either a 2 tier or single tier. I would love to have one of these but the limiting factor is the pump. I can not spend $100+ on a pump that handles boiling wort. That being said, am I really going to pump boiling liquid? I...

Ok, so I dont want to shell out the $100+ for a march pump that can handle hot wort. I am going to make a 3 tier system. I want to put the bottom tier about 12" off of the ground as I am limited in height in my apartment garage. I would like to cool the wort with an Immersion chiller then pump...

Hey, I just bought this at the Albertsons. It states that it is a one time use system, but I am hoping that it can be resused. Has anyone else seen these? Miller light also had one there. I grabed the last coors light one that was out, and there was only one miller light one left too. Maybe they...

Would there be any differences in boiling 8 gallons of wort for a 10 gallon batch? This way, I would boil 2 gallons of water say the night before to sterilize them, put them in sanitized 2liter bottles and freeze them. Then at the end of the boil of the 8 gallons, I would cut out the ice and put...

Just what the title says. I am going to build my first brew rig and step up from the turkey fryer. So, I am going to do a three tier rig because I do not want to buy a pump right now. I have three keggles (or have access to them) and one 10 gallon water cooler. Should I use a keggle or the water...

So, I want to buy a pond pump and put it in an ice chest with ice water and pump the ice water through my wort chiller and back into the ice chest. I have a 25' wort chiller and the water will have to travel up into and up out of my keggle (keg) brew pot. What gpm pump do you think I should use...

I usually use mapp gas to solder, but my father inlaw gave me a torch tip that he said he always uses on those little green propane tanks. I checked it when I got home, it does fit. Is this save? Will it work for me? I want to solder an elbow on my wort chiller so the tubing does not kink anymore.

I have been using hop pellets in a fine mesh bag for my brews. I use the bag so I dont have much material in my wort. First, does using the bag not allow all of the hop flavor/bitterness to be absorbed? Second, is there any benifits to using whole hops during the boil? Third, I have noticed...

Some of these are less then a dollar an ounce SHIPPED. They have good ratings on ebay. Do you trust? http://cgi.ebay.com/7-oz-Cascade-Pellet-Hops-5-9-AA_W0QQitemZ130363865307QQcmdZViewItemQQptZLH_DefaultDomain_0?hash=item1e5a4ab8db...

I have it in PDF format, how do I load it on here? I know how to include a pic, but I can not seem to save the PDF as a JPEG or anything other than PDF.