Search results

I went this route for the PWM. I have 24v pump http://m.ebay.com/itm/261678264066?_trksid=p2055119.m1438.l2649&_mwBanner=1 Used it twice without issue. No noise at any percentage and u can control it from 1-100%. Only "issue" I guess is if you turn pump on when it is set below X% (X% depends...

Here r some pics. First is the new switch. Sorry, the "plugs into outlet" should have been plugs into switch. The new switch has holds in the back for the wire. Insert wire and tighten screw. No connector needed. One of the connectors I used is still on the old switch. Hope these help.

10g wire and the little fork connectors. I am not using connectors for this switch since the wire plugs into outlet. After replacing the ssr and switch yesterday I ran a test session with just water (45 min mash hour boil) and everything went fine. Then I made an actual batch and it went...

http://m.ebay.com/itm/231326605882?_mwBanner=1 Here is the switch I had. It was probably running for 1.5 hours before this happened.

I am hoping this is what it is. It wasn't a household switch it was a cheap toggle with rubber boot. Just replaced with 30 2 pole house type switch. Line in connected to bottom 2 screws. Load out connected to top 2. Here we go again. Unfortunately I only have a 25a ssr on hand. This will get...

Black and red are hots Blue neutral Green ground Not sure 3 and 4 in drawing to ssr r correct but they r in the system. + to + and - to - Hope this helps.

Anyone?

Don't have one drawn but extremely simple 4 wire from box 30a breaker into 50a spa panel. From spa panel Hot: ssr to switch to outlet Hot: split to pid... other to switch then outlet White: pid Ground: outlet

So I finally got all on my equipment together and ran the auto tune for my pid which went fine (I think, temp held at 154 when set at 150 for almost an hour but felt hotter to touch than 154 so I will get thermo tomorrow to test it against). I put it in manual mode to bring to boil. Around...

Got the box finished tonight! And everything worked when I flipped the switches (which is never a guarantee) Now I need my kettle...

A little more progress. Slowly but surely. Bottom right is for the dpst switch for the element. Still waiting on it. Gotta figure out how to cut top left plate to install pid. Top right is switch and fuse for pid. Bottom left is switch and fuse for ssr fan (didn't mean to do fuse. Wired it in...

Oh wow. I was going to use a 1a fuse. Do u use a fuse? If so, what amperage?

What Guage of wire should I use to connect the power to the PID? I am using a 4 wire 240 . The only thing the neutral will connect to with my set up is the PID and I don't imagine I should hook up a 10ga wire to the PID. Thanks

http://www.ebay.com/itm/like/321750847104?lpid=82&chn=ps&ul_ref=http%253A%252F%252Frover.ebay.com%252Frover%252F1%252F711-117182-37290-0%252F2%253Fmtid%253D1588%2526kwid%253D1%2526crlp%253D53601919689_324272%2526itemid%253D321750847104%2526targetid%253D87946122609%2526rpc%253D0.16%2526rpc_upld_id...

1 pound in 5 gallons. OMG. I thought 5 oz was a lot. I may get there some day though. I planted a Chinook and cascade plant this spring. If those do well (they r only 6" tall in over a month for some reason) I will plant more so I don't have to spend 2-3$ an oz. I understand the new equipment...

OMG. I can't stop laughing. That's awesome.

So I am sitting here looking through my brew book,buzzing on some homebrew, and realized I keep increasing my ibu's. I started brewing in February. Before I drank bud light or Busch light. I liked craft beers but couldn't justify 10$ a 6 pack then started looking into brewing my own. Before I...

A couple more pictures of the 120 ran. Ordered all the other parts. Will update as I go but a lot is from China so it is going to be awhile

Thanks for all of the replies. I kegged the ipa and pale ale last night and set to 11psi. I have to dry hop the Belgium for 3 days with orange peel so will keg it Wednesday.

I have 15 feet if 3/8 line. I am going to run my kitchen so I don't have to go to the basement for beer. It is cooled up in kegerator for now with the taps just sticking out the side. I don't have much head retention so maybe I should try pushing psi by a couple. And see what that does.