ccostel
Well-Known Member
I have quite a bit of space under the burners and plan to add drip trays in case a boil over happens.
Show Me Your Wood Brew Sculpture/Rig
- Thread starter twst1up
- Start date
Help Support Homebrew Talk:
nag7
Member
here's my wood brew stand its a HERM's setup
user 103238
Well-Known Member
- Joined
- Jan 8, 2012
- Messages
- 569
- Reaction score
- 63
Nicely done! Simple, clean, and effective. This is right along the lines of what I have envisioned building.
nag7 said:
nag7
Member
thanks i used Kal's setup at www.theelectricbrewery.com as a start for mine and just changed it a little so i could store my propane tanks on the shelf.
fergusyarrow
Member
- Joined
- Apr 2, 2013
- Messages
- 10
- Reaction score
- 0
Hi guys,
I am just wondering, for those who build the frame around the burners, what do you use to stop the wood getting scorched?
Cheers,
Fergus
I am just wondering, for those who build the frame around the burners, what do you use to stop the wood getting scorched?
Cheers,
Fergus
I have each of the burners surrounded by a 20" W x 20" D x 6" H square (e.g., 80" circumference) of 0.096" sheet-metal bolted to the wood frame on the four corners. The wood doesn't even get warm, and I usually rest my fingers between the heat shield and the 2x4's. Remember, heat rises, so the only heat the wood is going to be exposed to is reflective heat from the sides of the kettle.
I just went into my gallery and found a pic that shows the heat shields...
You can see the two shields, one wrapped around each burner.
BrewingGunner
Well-Known Member
Here's mine. Almost complete.
blaster_54738
Well-Known Member
Where's the wood?
BrewingGunner
Well-Known Member
blaster_54738
Well-Known Member
Yeah I should have read the title. Oops!
Mighty fine looking rig you have there though, looks a lot like what I have in mind for my new build
Looks awesome and that's all that matters!
This is the stand I built over the winter. I only got a couple of batches through it before the little one showed up and took all my free time. Soon I hope to get back out there. It currently uses two BG-14's, one for the HLT and one under the BK.
Travestian
Well-Known Member
Put this guy through a couple of batches. Works great with the casters on it and it contains my entire brewery minus bottles when not in use.
jklapheke01
Member
I just finished my brew stand recently. I realize that there are those that may not agree on using wood for a brew stand with propane burners, but the basic design that I copied from a fellow member, along with the style of burners that I am using, I have had no issues with scorched or even warm wood at the writing of this note. Thank you to everyone who makes additions to this site.
I used this thread for a lot of design ideas and tweaked to what I knew I could build and what would work for the equipment I planned for. HLT is getting replaced with a 20 gallon BoilerMaker as soon as it arrives. Tons more pics in the link in my signature.
Travestian
Well-Known Member
Ever worry about running out of propane with 3 tanks under there?
I had four until last brew day. lol I just didn't go get the other refilled yet since I had spares. I had a bad experience with a couple of underperforming tanks once, so I wanted to make sure I didn't have to worry. Plus I had the space under there and have them handy for when the grill on the back patio runs out of LP at inconvenient times.
joeg13
Well-Known Member
I'm planning to build a two tier system with a propane burner on lower level. Are you guys using a fire retardant sealer on the wood? I'm concerned that polyurethane or varnish would be flammable or give off fumes.
joeg13
Well-Known Member
Just used my new woody for the first time yesterday, its not quite done as I'm waiting to add the blichmann tower of power to automate the mash temp if it ever gets done. And have to wire the pumps to a more permanent solution as well.
I have the Blichman burners also. Are the sitting right on the wood? I assumed the would get hot underneath and burn the wood.
MetallHed
Well-Known Member
From the pic it looks like he has a sheet of something fastened to the top of the rig underneath the burners.
I put a coat of Thompson's water sealer. That being said, I think some of the paranoia about stands catching on fire is just that. After all, you stand closer to the flame when you're stirring your wort. The base under my burners gets hotter from the sunlight than it does from the burners. I don't think I'd try to build a frame for multi-jet burners out of wood, but with a banjo burner sitting on top of one, I'm not that worried.
I used a stain poly blend on my single tier stand. The first time I used it you could smell a little bit of the stain but after the first heating cycle I have had no problems since. That was probably only due to the fact that I didn't get a chance to really let the stain cure due to the stand living in my garage in the winter.
I did put heatshields around my banjo burners, but even cranked up, the keg gets red hot before I worry about the wood. Just give it enough spacing to keep the air flowing around it and you will be fine.
Travestian
Well-Known Member
I've never had to worry about my stand getting warm at all from the burners. I agree though about not building a frame for multi jet burners. Or any burner for that matter. I used a clear polyurethane and have had no issues.
When I first built my woody, I can still remember that first day... lighting up the burner, fully prepared to see a remake of the towering inferno, right there in my back yard. Six years later, and it's still going strong. In fact, I'm in the middle of completing Woody Version 2.0... BIGGER, STRONGER, AUTOMATED, INTEGRATED MILL & CONTROL PANEL... but still made out of wood!!
Similar threads
