New York Gear Sale

[Big Monk]

I'm taking an indefinite hiatus from brewing. I have so much going on and I won't have time to brew for long enough that I'm just going to take a break indefinitely.

As a result I'm getting rid of my gear. The list is shown below. Prices are fair and below what you'd get them for new. I'll do my best to keep shipping as low as I can. The system is setup right now for a 3 gallon kettle but I also have a 4 gallon. The system is functional as a single vessel Low Oxygen system but will likely be too small for most if you. I'm wiling to sell as a complete system.

Cereal Killer mill with hopper and base - $85
Waring Pro SB30 Burner with temp cutoff bypassed - $30
Raspberry Pi 3b, SD Card (with OS), RPi case, hookup wires - $50
5 one wire sensors, 2 mounted with removable cam locks - $35
3 gal kettle - $5
4 gal kettle - $7.50
9" False Bottom - $25
4 bags Oxygen caps (Red, Yellow, Blue, White) - $15
Red Capper - $12
25' SS Chiller - $30
Female Cams - $2.50 each
Male Cams - $2.50 each
12v solar pump with cam lock fittings and power supply - $20
Camlocks with 3/8" barbs - $3.50 each
Grains - $1 p/lb
1/2" ball valve - $5
Locknuts and orings - $1.50 each (each locknut with an oring
Elbows - $1.50 each
Refractometer - $15
Colorphast strips - ~30 for $5
pH Meter (pen type with buffers) - $20
Tees - $2 each
Cam lock caps - $3 each
TC to male NPT - $5 each (each comes with 2 gaskets)
TC clamps - $5 each
Locline circle flow kit - $15
Gram scale - $5
Hydrometer - $7
Thermowell - $5
Whirlpool inlet with compression fitting - $9

 

[cubalz]

I would be interested in the refractometer and the thermowell. Would you be able to send me a picture of each to [email protected]?

Thanks!
John

 

[vsanchez949]

PM Sent

 

[fourfarthing]

What part of NY?

 

[abrew2u]

Interested in cereal killer where in ny are you

 

[Esmitee]

May want the " TC to male NPT - $5 each (each comes with 2 gaskets)
TC clamps - $5 each"
What size TC ?

 

[Big Monk]

Interested in cereal killer where in ny are you

Near Syracuse. It's still available.

 

[Big Monk]

May want the " TC to male NPT - $5 each (each comes with 2 gaskets)
TC clamps - $5 each"
What size TC ?

1/2" ID with a 1.5" TC size.

 

[Paulaner]

Is your setup the same as the one in http://www.********************/forum/viewtopic.php?f=2&t=312&start=10 If so how much for the whole kettle setup?

 

[Esmitee]

Oh, I needed 2" Thanks

 

[Big Monk]

Is your setup the same as the one in http://www.********************/forum/viewtopic.php?f=2&t=312&start=10 If so how much for the whole kettle setup?

This one?:

View attachment ImageUploadedByHome Brew1504000030.392363.jpg

If so, then yes, that's the one. Plus the 1300w burner and Raspberry Pi automation setup.

 

[vsanchez949]

Interested in the ph meter and camlocks. I need three 1/2" males if you have them? What's the brand of the ph meter?

 

[Big Monk]

Interested in the ph meter and camlocks. I need three 1/2" males if you have them? What's the brand of the ph meter?

I sent you a PM but it's a no name stick brand. Calibrates and works well. I store it in KCl solution. I have 1/2 bottles each of 4 and 7 buffers and a nearly full bottle of storage solution.

View attachment ImageUploadedByHome Brew1504010715.298661.jpg

I also have a nearly full pack of Colorphast strips as well.

I believe I have 2-3 1/2" Males among others. I need to do an inventory tonight.

 

[vsanchez949]

Didn't get the PM. I will take the PH meter and 3 camlocks if you have them. Thanks!

 

[Santo]

Price? whole set up...

View attachment 412223

If so, then yes, that's the one. Plus the 1300w burner and Raspberry Pi automation setup.[/QUOTE]

 

[Paulaner]

This one?:

View attachment 412223

If so, then yes, that's the one. Plus the 1300w burner and Raspberry Pi automation setup.

PM sent.

 

[Big Monk]

Didn't get the PM. I will take the PH meter and 3 camlocks if you have them. Thanks!

Shoot me a PM with your shipping info and I'll get a quote

 

[Big Monk]

UPDATE:

I'm working through a sale of the bulk of the stuff sold as a system. The rest is as follows:

Cereal Killer mill with hopper and base - $85
4 bags Oxygen caps (Red, Yellow, Blue, White) - $15
Red Capper - $12
25' SS Chiller - $30
Refractometer - $15
Colorphast strips - ~30 for $5
pH Meter (pen type with buffers) - $20
Gram scale - $5
Hydrometer - $7
Thermowell - $5

 

[Big Monk]

Price? whole set up...



View attachment 412223



If so, then yes, that's the one. Plus the 1300w burner and Raspberry Pi automation setup.

[/QUOTE]


PM me and we can talk about a package deal.

 

[Big Monk]

Edit

 

[vsanchez949]

I will still take the cams and the PH meter if it's still available?

 

[Big Monk]

I will still take the cams and the PH meter if it's still available?

I've tried PM'ing you a few times to get your address for shipping.

 

[Big Monk]

Interested in cereal killer where in ny are you

Still interested?

 

[scsnow1]

Is the 1/2” ball valve stainless?

 

[scsnow1]

My bad I see the picture now. If you still have the ball valve I’ll take it if willing to ship.

 

[Big Monk]

My bad I see the picture now. If you still have the ball valve I’ll take it if willing to ship.

Send me a PM with your shipping info and i'll get it right out.

 

[Big Monk]

Snapped some pictures today (finally):

View attachment ImageUploadedByHome Brew1504203550.518096.jpg

1.5" Full Thread Nipples (2) - $3 each
Stainless Whirlpool Inlet with Compression Fitting (1) - $9
1/2" NPT to 1.5" TC (2) - $5 (includes 2 TC Gaskets) each
Triclover Clamps (2) - $5 each
1/2" Mini Ball Valve (1) - $4
1/2" NPT Male Camlock Fittings (4) - $2.50 each
1/2" NPT Female Camlock Fittings (3) - $2.50 each
1/2" Washers (4) - $1.50 each
1/2" NPT Female/Male Elbow (1) - $2.50
High Flow 90 (1) - $3
1/2" NPT Male to 3/8" Barb Elbow (1) - $1.50
1/2" Elbows (1) - $2 each
3/8" Barb Camlocks (7) - $3.50 each
1/2" NPT Female Camlocks (2) - $3.50 each
Camlock Caps (2) - $3 each
3/8" Barb to Camlock Fitting (1) - $2
1/2" Locknuts (14) - $1 each
10" Thermowell (1) - $5
1/2" Ball Valve (1) - $5
Locline Circle Flow Kit (1) - $12
12v 100C Solar Pump w/ Camlock Fittings (1) - $20
1/2" NPT Tee (2) - $2 each

View attachment ImageUploadedByHome Brew1504203573.588991.jpg

Raspberry Pi 3b w/ case, hookup wires, SSRs, Preloaded SD Card - $50
4 One-Wire Sensors, Bored Through Compression and Long Tubes - $25

View attachment ImageUploadedByHome Brew1504203590.406644.jpg

Waring Pro Burner with Bypassed Thermostat - $25

View attachment ImageUploadedByHome Brew1504203609.356871.jpg

Cereal Killer Grain Mill - $80

View attachment ImageUploadedByHome Brew1504203627.124879.jpg

Capper and Red, Yellow, Blue and White Caps - $22

View attachment ImageUploadedByHome Brew1504203644.800807.jpg

Aquarium pump with extra sterile filter - $15

Everything in these pictures and then some is up for grabs.

 

[vsanchez949]

I have no idea why my PMs aren't working. Mailbox is clear. [emoji58] can you email me a total including shipping to 92679 and your PayPal info? Thanks!
[email protected]

 

[Big Monk]

Thanks to all those that have reached out so far. I'll be writing down addresses and preparing shipping packaging and estimates this weekend. I plan on shipping the stuff that has been claimed so far on Monday.

Please make sure you've sent a PM with items desired and shipping information and i'll be sure to get stuff out early next week.

 

[WPStrassburg]

interested in the chiller if its still available. I'm out in Rochester and could pickup at some point if you can hold it. Any photos of it?

 

[newuser12345]

pm sent

 

[Big Monk]

Have had some stalled sales so I wanted to put this out there again. I have all the equipment broken down and ready to ship. Juts PM with address and zip code and i'll get the stuff out same day.

View attachment 412488

1.5" Full Thread Nipples (2) - $3 each
Stainless Whirlpool Inlet with Compression Fitting (1) - $9
1/2" NPT to 1.5" TC (2) - $5 (includes 2 TC Gaskets) each
Triclover Clamps (2) - $5 each
1/2" Mini Ball Valve (1) - $4
1/2" NPT Male Camlock Fittings (4) - $2.50 each
1/2" NPT Female Camlock Fittings (3) - $2.50 each
1/2" Washers (4) - $1.50 each
1/2" NPT Female/Male Elbow (1) - $2.50
High Flow 90 (1) - $3
1/2" NPT Male to 3/8" Barb Elbow (1) - $1.50
1/2" Elbows (1) - $2 each
3/8" Barb Camlocks (7) - $3.50 each
1/2" NPT Female Camlocks (2) - $3.50 each
Camlock Caps (2) - $3 each
3/8" Barb to Camlock Fitting (1) - $2
1/2" Locknuts (14) - $1 each
10" Thermowell (1) - $5
1/2" Ball Valve (1) - $5
Locline Circle Flow Kit (1) - $12
12v 100C Solar Pump w/ Camlock Fittings (1) - $20
1/2" NPT Tee (2) - $2 each

View attachment 412489

Raspberry Pi 3b w/ case, hookup wires, SSRs, Preloaded SD Card - $50
4 One-Wire Sensors, Bored Through Compression and Long Tubes - $25

View attachment 412490

Waring Pro Burner with Bypassed Thermostat - $25

View attachment 412491

Cereal Killer Grain Mill - $80

View attachment 412492

Capper and Red, Yellow, Blue and White Caps - $22

View attachment 412493

Aquarium pump with extra sterile filter - $15

 

[Shwagger]

Wondering what happened, never heard back from last pm

 

[kjf45]

PM sent.

 

[Big Monk]

Wondering what happened, never heard back from last pm

Sorry I missed that. PM sent

 

[Big Monk]

Have had some stalled sales so I wanted to put this out there again. I have all the equipment broken down and ready to ship. Juts PM with address and zip code and i'll get the stuff out same day.

View attachment 412488

1.5" Full Thread Nipples (2) - $3 each
Stainless Whirlpool Inlet with Compression Fitting (1) - $9
1/2" NPT to 1.5" TC (2) - $5 (includes 2 TC Gaskets) each
Triclover Clamps (2) - $5 each
1/2" Mini Ball Valve (1) - $4
1/2" NPT Male Camlock Fittings (3) - $2.50 each
1/2" NPT Female Camlock Fittings (1) - $2.50 each
1/2" Washers (4) - $1.50 each
1/2" NPT Female/Male Elbow (1) - $2.50
High Flow 90 (1) - $3
1/2" NPT Male to 3/8" Barb Elbow (1) - $1.50
1/2" Elbows (1) - $2 each
3/8" Barb Camlocks (4) - $3.50 each
1/2" NPT Female Camlocks (2) - $3.50 each
Camlock Caps (2) - $3 each
3/8" Barb to Camlock Fitting (1) - $2
1/2" Locknuts (14) - $1 each
Locline Circle Flow Kit (1) - $12
12v 100C Solar Pump w/ Camlock Fittings (1) - $20
1/2" NPT Tee (2) - $2 each

View attachment 412489

Raspberry Pi 3b w/ case, hookup wires, SSRs, Preloaded SD Card - $50
4 One-Wire Sensors, Bored Through Compression and Long Tubes - $25

View attachment 412490

Waring Pro Burner with Bypassed Thermostat - $25

View attachment 412491

Cereal Killer Grain Mill - $80

View attachment 412492

Capper and Red, Yellow, Blue and White Caps - $22

View attachment 412493

Aquarium pump with extra sterile filter - $15

See updated quantities above

 

[rjolin01]

Pm sent

 

[Big Monk]

9/19/2017 - UPDATED LIST

Had some sales and here is a revised list:

View attachment 412488

1.5" Full Thread Nipples (1) - $3 each
Stainless Whirlpool Inlet with Compression Fitting (1) - $8
1/2" NPT to 1.5" TC (2) - $5 (includes 2 TC Gaskets) each
Triclover Clamps (2) - $5 each
1/2" Washers (1) - $1.50 each
1/2" NPT Female/Male Elbow (1) - $2.50
1/2" NPT Male to 3/8" Barb Elbow (1) - $1.50
1/2" Elbows (1) - $2 each
3/8" Barb Camlocks (4) - $3.50 each
1/2" NPT Female Camlocks (2) - $3.50 each
3/8" Barb to Camlock Fitting (1) - $2
1/2" Locknuts (10) - $1 each
12v 100C Solar Pump w/ Camlock Fittings (1) - $20


View attachment 412489

Raspberry Pi 3b w/ case, hookup wires, SSRs (1 DC and 1 AC), Preloaded SD Card - $47
4 One-Wire Sensors, Bored Through Compression and Long Tubes - $22

View attachment 412490

Waring Pro Burner with Bypassed Thermostat - $25

View attachment 412491

Cereal Killer Grain Mill - $80

View attachment 412492

Capper and Red, Yellow, Blue and White Caps - $20

View attachment 412493

Aquarium pump with extra sterile filter - $15

 

[rjolin01]

Pm sent again

 

[TheLostBeer]

I would do the rasp pi and tubes, sent pm