Specialty IPA: Rye IPA Denny Conn's Wry Smile Rye IPA

[Denny]

I almost never do a secondary for this beer, but if I do it's about 2 weeks and I dry hop the entire time. Then I add more dry hops to the keg.

 

[flyingfinbar]

OK...2oz of Columbus for dry hop lined up for this beer. If I have an extra half oz of Cascade, should I toss it in too, or would the aromas clash?

 

[Clifton]

Save that Cascade for BM's Centennial Blonde.

 

[kevin476]

It won't clash. Just try it. Next Tim I brew this one I'll do 1 oz of Columbus for a week and then one more when I pull that one out.

 

[Clifton]

Seriously, if you haven't done BierMuncher's blonde save the 1/2 ounce for that. I'm sure Denny would agree with me. Especially if this is the first time you've made Wry Smile.

 

[maltoftheearth]

Wow - I brewed this earlier in the year and just cracked it open for the first time tonight. Best beer I have made in the last three years, hands down fantastic. Wow. Used a hop tea for the aroma and it was just the trick. This recipe rocks!

 

[flyingfinbar]

Ok, so I'm gonna stick to 2oz of Columbus for the dry hops...how long do you let this beer age? Is it better young, like some IPAs? Or do you let it age out a bit?

 

[maltoftheearth]

Ok, so I'm gonna stick to 2oz of Columbus for the dry hops...how long do you let this beer age? Is it better young, like some IPAs? Or do you let it age out a bit?

I let mine set at least a month in a keg at 34F before cracking it open. Then again, my ales are sometimes a little wonky and it was suggested I lager them a bit before consuming.

 

[Denny]

Ok, so I'm gonna stick to 2oz of Columbus for the dry hops...how long do you let this beer age? Is it better young, like some IPAs? Or do you let it age out a bit?

I generally like to drink it within a few weeks of brewing.

 

[E-rok]

can i make this recipe with a 5 gallon mash tun?

 

[Yooper]

can i make this recipe with a 5 gallon mash tun?

I use this "can I mash it?" calculator to find out if a grainbill will fit in my MLT. http://www.rackers.org/calcs.shtml

With a mash ratio of 1.25 quarts/pound, a grain bill of this size will take up 6.28 gallons of space, not including the false bottom. So, I'd say no. But you could use 2-3 pounds of DME instead of some of the two-row and make it a partial mash very easily.

Just use 3 pounds of DME for 5 pounds of grain (two-row). That would give you 11.25 pounds of grain, which WILL fit! And just finish that and add the DME to the boil kettle and proceed. That would work very well with this recipe and a 5 gallon MLT.

 

[E-rok]

awesome, thank you so much!

 

[Denny]

can i make this recipe with a 5 gallon mash tun?

If you make a 3 gal. batch it will probably work. At the 1.5 qt./lb.ratio I use, a mash for a 5 gal. batch uses 7.9 gal. of volume.

 

[E-rok]

I ended up doing what yooper said, however, depending on my results a 3 gallon batch or a new mash tun are in my future

 

[E-rok]

Type: All Grain Date: 04/17/2012
Batch Size (fermenter): 5.00 gal Brewer:
Boil Size: 6.52 gal Asst Brewer:
Boil Time: 60 min Equipment: Pot and Cooler ( 5 Gal/19 L) - All Grain
End of Boil Volume 5.98 gal Brewhouse Efficiency: 72.00 %
Final Bottling Volume: 5.02 gal Est Mash Efficiency 89.6 %
Fermentation: Ale, Two Stage Taste Rating(out of 50): 30.0
Taste Notes:
Ingredients

Ingredients
Amt Name Type # %/IBU
6 lbs Pale Malt (2 Row) US (1.7 SRM) Grain 1 39.9 %
2 lbs 12.0 oz Rye Malt, German (3.5 SRM) Grain 2 18.3 %
1 lbs Caramel Malt - 40L (Briess) (40.0 SRM) Grain 3 6.6 %
8.0 oz Cara-Pils/Dextrine (2.0 SRM) Grain 4 3.3 %
8.0 oz White Wheat Malt (2.4 SRM) Grain 5 3.3 %
1 lbs Dark Dry Extract (17.5 SRM) Dry Extract 6 6.6 %
3 lbs 4.8 oz LME Golden Light (Briess) (4.0 SRM) Extract 7 21.9 %
1.00 oz Matueka [7.40 %] - Boil 75.0 min Hop 8 20.0 IBUs
1.00 oz Pacific Jade [14.40 %] - Boil 75.0 min Hop 9 39.0 IBUs
1.50 oz Matueka [7.40 %] - Boil 45.0 min Hop 10 26.4 IBUs
0.50 oz Matueka [7.40 %] - Boil 0.0 min Hop 11 0.0 IBUs
1.0 pkg Denny's Favorite 50 (Wyeast #1450) Yeast 12 -
1.00 oz Pacific Jade [14.40 %] - Dry Hop 7.0 Days Hop 13 0.0 IBUs
Beer Profile

Est Original Gravity: 1.087 SG Measured Original Gravity: 1.088 SG
Est Final Gravity: 1.019 SG Measured Final Gravity: 1.030 SG
Estimated Alcohol by Vol: 9.0 % Actual Alcohol by Vol: 7.7 %
Bitterness: 85.5 IBUs Calories: 310.2 kcal/12oz
Est Color: 10.0 SRM
Mash Profile

Mash Name: Single Infusion, Medium Body, Batch Sparge Total Grain Weight: 15 lbs 0.8 oz
Sparge Water: 4.70 gal Grain Temperature: 72.0 F
Sparge Temperature: 168.0 F Tun Temperature: 72.0 F
Adjust Temp for Equipment: TRUE Mash PH: 5.20
Mash Steps
Name Description Step Temperature Step Time
Mash In Add 13.44 qt of water at 167.1 F 152.0 F 60 min
Sparge Step: Batch sparge with 3 steps (0.19gal, 2.26gal, 2.26gal) of 168.0 F water
Mash Notes: Simple single infusion mash for use with most modern well modified grains (about 95% of the time).
Carbonation and Storage

Carbonation Type: Keg Volumes of CO2: 2.3
Pressure/Weight: 7.72 PSI Carbonation Used: Keg with 7.72 PSI
Keg/Bottling Temperature: 35.0 F Age for: 30.00 days
Fermentation: Ale, Two Stage Storage Temperature: 61.0 F
Notes

spilled about a pound of grain at mash in, whirlfloc at flame-out, forgot to check for starch conversion
Created with BeerSmith



ok, there is my recipe. It has been a week and gravity is at 1.030, I was hoping for 1.020. I made a 1.6L starter. Should I try swirling it everyday? pitch more yeast? just wait another week and see? I was hoping to move to secondary today to dry hop.

 

[Denny]

Why the heck did you do 3 sparge additions?

 

[E-rok]

5 gallon mash tun, and beer smith told me to.

 

[Denny]

5 gallon mash tun, and beer smith told me to.

Forget what Beersmith "tells" you to do. The only reason to do more than one sparge is if you can't fit all the sparge water in your cooler at once.

 

[E-rok]

another gravity*reading today and it reads at 1.028, what should I do?

 

[Denny]

another gravity*reading today and it reads at 1.028, what should I do?

Wait 2 more weeks then get back to us.

 

[qwd890]

I was just going to try a rye and ran across this recipe and thread--

Looks like my LHBS doesn't carry WY1450, and my "house strain" is WL028 Scottish- it sounds like maybe some of the same(ish) characteristics like accentuating malt & caramel, about same attenuation and good with hops... would it be close enough to do the recipe justice or just buy a new one in the list?

 

[Denny]

I'm not familiar with that yeast so I really can't say if it'll be a good sub. Chances are it'll be close but not the same.

 

[SkinnyPete]

Oh boy. I just finished brewing this and everything went exactly as planned. Hit all numbers spot on. But, a bit of a problem - I just didn't notice how high of original gravity this thing was until I was boiling. Not sure how that got past me but I wasn't prepared with a starter. I pitched the WYEAST liquid packet after it had swelled good but it was too late for a starter. Any suggestions? Maybe double pitch? I could try to grab another packet of yeast but won't be able to get 1450 locally, I'm sure. Any suggestions? Hope I didn't botch this.

 

[frazier]

Just bottled my first try at this recipe. Yes, the hydro sample tasted great. I've used WY1450 many times, but this time it took my down to 1.012 - nearly 80% attenuation! I'm really looking forward to cracking one open in a few weeks.

As for the Edinburgh yeast question from gwd890 - I've also used that yeast a lot, and like it, but.... If you're itching to brew today, and don't have 1450, brew something else that you like, and then make Wry Smile when you've got everything lined up.

 

[SkinnyPete]

Just an update. This thing took off quickly without a starter. It's 20 hours later and I need a blowoff tube. I'm assuming it'll still end on the high FG end of things but I've got a couple batches already in secondary so I'm going to keep it in primary for 3 weeks and see where I end up. If it's crazy high, I'll just pitch again. I'm sure I can get my hands on another 1450 by that time.

 

[qwd890]

Thanks for the feedback on the Edinburg yeast question- I think I'll take Frazier and Mae's advice and hold off til it can be done properly

 

[Denny]

I'll try not to be offended that you said my beer tasted like Ruthless....personally, I find that kind of a wimpy beer without enough rye to really be noticeable.

 

[E-rok]

Type: All Grain Date: 04/17/2012
Batch Size (fermenter): 5.00 gal Brewer:
Boil Size: 6.52 gal Asst Brewer:
Boil Time: 60 min Equipment: Pot and Cooler ( 5 Gal/19 L) - All Grain
End of Boil Volume 5.98 gal Brewhouse Efficiency: 72.00 %
Final Bottling Volume: 5.02 gal Est Mash Efficiency 89.6 %
Fermentation: Ale, Two Stage Taste Rating(out of 50): 30.0
Taste Notes:
Ingredients

Ingredients
Amt Name Type # %/IBU
6 lbs Pale Malt (2 Row) US (1.7 SRM) Grain 1 39.9 %
2 lbs 12.0 oz Rye Malt, German (3.5 SRM) Grain 2 18.3 %
1 lbs Caramel Malt - 40L (Briess) (40.0 SRM) Grain 3 6.6 %
8.0 oz Cara-Pils/Dextrine (2.0 SRM) Grain 4 3.3 %
8.0 oz White Wheat Malt (2.4 SRM) Grain 5 3.3 %
1 lbs Dark Dry Extract (17.5 SRM) Dry Extract 6 6.6 %
3 lbs 4.8 oz LME Golden Light (Briess) (4.0 SRM) Extract 7 21.9 %
1.00 oz Matueka [7.40 %] - Boil 75.0 min Hop 8 20.0 IBUs
1.00 oz Pacific Jade [14.40 %] - Boil 75.0 min Hop 9 39.0 IBUs
1.50 oz Matueka [7.40 %] - Boil 45.0 min Hop 10 26.4 IBUs
0.50 oz Matueka [7.40 %] - Boil 0.0 min Hop 11 0.0 IBUs
1.0 pkg Denny's Favorite 50 (Wyeast #1450) Yeast 12 -
1.00 oz Pacific Jade [14.40 %] - Dry Hop 7.0 Days Hop 13 0.0 IBUs
Beer Profile

Est Original Gravity: 1.087 SG Measured Original Gravity: 1.088 SG
Est Final Gravity: 1.019 SG Measured Final Gravity: 1.030 SG
Estimated Alcohol by Vol: 9.0 % Actual Alcohol by Vol: 7.7 %
Bitterness: 85.5 IBUs Calories: 310.2 kcal/12oz
Est Color: 10.0 SRM
Mash Profile

Mash Name: Single Infusion, Medium Body, Batch Sparge Total Grain Weight: 15 lbs 0.8 oz
Sparge Water: 4.70 gal Grain Temperature: 72.0 F
Sparge Temperature: 168.0 F Tun Temperature: 72.0 F
Adjust Temp for Equipment: TRUE Mash PH: 5.20
Mash Steps
Name Description Step Temperature Step Time
Mash In Add 13.44 qt of water at 167.1 F 152.0 F 60 min
Sparge Step: Batch sparge with 3 steps (0.19gal, 2.26gal, 2.26gal) of 168.0 F water
Mash Notes: Simple single infusion mash for use with most modern well modified grains (about 95% of the time).
Carbonation and Storage

Carbonation Type: Keg Volumes of CO2: 2.3
Pressure/Weight: 7.72 PSI Carbonation Used: Keg with 7.72 PSI
Keg/Bottling Temperature: 35.0 F Age for: 30.00 days
Fermentation: Ale, Two Stage Storage Temperature: 61.0 F
Notes

So I am tasting the first pint of this now, FG got to 1.022, i dry hopped for a week with 1 ounce Pacific Jade and 1 ounce Matueka. Cold crashed 5 days or so. Force Carbed starting 3 days ago and today it is pretty well carbed. I know it is young, but I am impatient. It is a little cloudy, but I am sure tht it will clear in time.

So tasty! I may add a little more rye next time, but it is amazingly good and really smooth given its 9% abv. Thank you Denny for a wonderful recipe!

 

[kevin476]

I'll try not to be offended that you said my beer tasted like Ruthless....personally, I find that kind of a wimpy beer without enough rye to really be noticeable.

I agree I hardly notice the rye in ruthless. Denny's is so much more delicious.

 

[kevdoggx]

I hate to go back to the beginning of this thread, but I just found this recipe and the first few posts gave me a bit of confusion. The OP said SG would be 1.085, which is in line with my calculations and every program that I've plugged this recipe into. But Denny, you yourself said you had some fermenting that came out at 1.073. What is the reason for the discrepancy between the gravities? Does it have something to do with the rye?

Thanks for the clarification!