• Please visit and share your knowledge at our sister communities:
  • If you have not, please join our official Homebrewing Facebook Group!

    Homebrewing Facebook Group

BIAB Electric Brewery

Homebrew Talk

Help Support Homebrew Talk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

ameliabrewery

Supporting Member
HBT Supporter
Joined
May 14, 2010
Messages
129
Reaction score
3
Location
Virginia
Well here I go. I have brewed AG with my current biab setup and have enjoyed it immensely. I have purchased the equipment to go electric and it should start arriving today via FedEx. Looking forward to getting home today and start unboxing. At that time I will start posting pics.
 
Well here I go. I have brewed AG with my current biab setup and have enjoyed it immensely. I have purchased the equipment to go electric and it should start arriving today via FedEx. Looking forward to getting home today and start unboxing. At that time I will start posting pics.

Excellent choice! Can't wait to see your pics. :ban:
 
Well here is the first batch of goodies!

image-133814362.jpg
 
Have been looking at those Auberins buttons, do they feel high quality? Are you going with a 120v or 240v system?
 
Sweet start. I only have a hundred Amp service to my house so I have been skeptical on moving electric. Keep us updated.
 
Have been looking at those Auberins buttons, do they feel high quality?

Not my build, but I have the Auber illuminated push buttons. They do feel high quality and have a nice haptic feedback click when you press them. I would recommend them to anyone.
 
Sorry I did not reply sooner, I was out partaking in fine brew. Yes the buttons are very nice, and have a solid feel. I got a nice box from my father in law who is a master electrician. Love freebies! I will post some pics tomorrow.
 
Got my box. It had goodies in it but I am only using the connector block. Also picked up my spa panel. Now off to super bowl party! I am an Eagles fan, but guess I will side with the Giants, cannot stand NE. Hope that does not upset anyone :)

image-525345645.jpg


image-1231287379.jpg


image-3014383218.jpg
 
Got some time to work on my control panel today. If you guys see something wrong please tell me. The wires running off to the right side are for main power coming in. I am going to hard wire a cord in the panel box with those wires.

image-4097738644.jpg


image-3573788753.jpg
 
You should post a schematic and larger (high resolution) images if you want feedback. The schematic will allow people to comment on the design. The larger (high resolution) images will allow people to comment on how you implemented the design.

It's impossible to tell anything from just small pictures like this. The parts can't be seen and the wiring is impossible to follow.

Kal
 
Check your e-stop button. Usually a red contact block on the back of the switch means it is a NC (normally closed) contact. This means the e stop button would have to be pushed in for the brewery to work and released to trip the estop (basically it will be backwards). If you leave it the way its wired up now the GFI breaker will trip every time you plug in the panel.

You need a NO (normally open) contact. Something like this will work: http://www.automationdirect.com/adc/Shopping/Catalog/Pushbuttons_-z-_Switches_-z-_Indicators/22mm_Plastic/22mm_Pushbutton_Accessories/Contact_Blocks/ECX1040-5
 
DANG!! :mad: You are right! Well, just ordered the right one. Thanks for catching that goof. If I had just went with the part number on P-Js schematic I would not have wasted the money, but I wanted a red instead of yellow and did not pay attention to no versus nc. :drunk:

Oh by the way, thanks P-J for allowing me to steal your schematic!:rockin:
 
Yeah I found a red button on eBay that says "STOP" for mine. It was NC though so I bought an identical NO albeit black-faced button so I could swap contacts.
 
I can't give you a technical electric code reason, but I don't really like having the receptacles on the front of the panel. Since you already did that you might consider using plugs with 90 degree angle feeds so the wires hang straight down instead of out and straining.
 
I am using parts I already have. That includes right angle plugs. My father in law owns an electrical company so freebies trump all the fancy twist lock plugs. :)
 
You will be surprised how quickly you heat water and how efficient your brewery has just become!
 
ameliabrewery said:
I am heating water!!!!! Yeee hawww! I will post my heat time shortly.

I have the same kettle and did my recirculation with a street elbow and some camlocks through the lid. Allows me to close the lid all the way.
 
I have those parts already. I am installing tomorrow before my first brew. Also need to finish enlarging the holes in my basket. Should have an IPA in the fermenter by dinner.
 
Back
Top