Search results

My Auber controller has been having a ton of error messages so I'm hoping to swap it out to see if things improve. if you have one laying around that you want to get rid of let me know!

pm sent

Yes! It's Alive! Thank you all for your suggestions! After a ton of poking around with my multimeter I finally found out that my female XLR port on the control panel wasn't connecting to the cable very well. if the cable was held at an angle it would have a stable temp reading. After six months...

i need to check with a multimeter tomorrow but right now what happens is that it goes from the random numbers to OrAL and back again. I’ll check the continuity of the probe and the cable and see if there is any more info… i did try swapping the connections on the PID but it immediately went to...

hmm.. In the instruction manual for the DSPR 120 (EZBoil) it says that it's only compatible with PT100 RTD sensors so I don't think there are any settings to switch? The fitting the probe fits in is a pull through and soldered fitting from brew hardware. Are you thinking something to do with...

So I've been electric brewing for a while now but in the past 6 months I've gone ahead and built myself an EZ Boil PID control box. During the first brew day with the controller there was clearly something very wrong with the temp probe because the PID was going from an error message to a...

I believe I also have one that I never used… I don’t have the temperature probe though. It sounds like you have already picked up a unit l but if not I would be happy to sell it to you.

I know you’re build has been done for a while now but I have been building mine for a few months now and have a question on your wiring schematic. Maybe it’s a question I know you’re build has been done for a while now but I have been building mine for a few months and have a question on your...

I'll have to double-check my wire gauge. When the power comes into the brew controller I have a 30amp breaker as the first destination before electrifying anything else.

I'm in the process of building a 30 Amp ebiab controller, that should be done in the next few weeks! I had an electrician wire a new spa panel to my back patio and I went out the other day and realized it's actually a 50A GFCI breaker which I think is the more standard option for hot tubs. My...

price dropped to 200 shipped

From what you just said it sounds like you do the same process as me. I start my boil with 6.5 gallons and end with 5.25 in the fermentor. you definitely want more than 3 gallons to fully saturate your mash. my mash water volume is usually around 6 or so gallons, I lose some to the grains. then...

I've never used the clawhammer system before but I have been doing single vessel ebiab for 7ish years. For me to get my efficiency numbers up I actually reserve a portion of my calculated mash water to use as a rinse. My process: raise the strainer basket and let drain, use a pan lid or some...

Price dropped to 210 + shipping. I didn't realize how much the price of these has changed!

I bought this hoping to build a keezer under a bar but I think that may be a ways away still. Hoping to sell for $260 + shipping. Local pickup would be preferred but there aren’t a ton of brewers in Utah ha. I’ll add photos shortly!

hey Pablo, can I ask what set up you eventually went with? I’m considering putting a 240v ripple in an 11g bayou kettle for my “final” ebiab rig. Curious to know if you ran into issues with the element hitting the kettle.

It's been a while since I last posted but I've got a question I can't seem to find an answer to! I just bought an Inkbird IPB-16S but I'm wanting to upgrade the temperature probe with a PT100 using XLR connections out of the project box. the Inkbird currently has an 1/8th inch jack temp probe...

+1 for me! Would be an awesome upgrade

After the raspberry false alarm I was sure I wasn't mistaken as my hops literally exploded in the warm Utah weather we've been having. So two days ago this is what my hops looked like. Sitting at a warm 75 degrees they were happy happy happy. And this is what it looked like yesterday...