Recent content by gcrisler

Williams 728
Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum

Help Support Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. G

    MD/DC grain

    I'd like to add a few sacks to this order: 8 x CM-2ROW 1 x CM-RYEM 1 x CM-WHET PM me a price estimate if possible? Thanks!
  2. G

    MD/DC grain

    how does payment work? still the same as stated on the first page of the thread?
  3. G

    MD/DC grain

    calphamsa looks like we've got one sack to go? Is there a chance they wont have some of the sacks i'm after? thanks!
  4. G

    MD/DC grain

    Put me down for these: 8 sacks CM-2 row 1 sack CM-Rye malt 1 sack TF-AMBR 1 sack TF-BRWN 1 sack BD-CHLT 1 sack BD-RSTB 1 sack BD-CRSN whats that put the count at? thanx!
  5. G

    Cut in cooler lining help

    Anybody have have an opinion on the epoxy I chose? The Water Weld stuff.
  6. G

    Cut in cooler lining help

    went with this http://jbweld.net/products/water.php heat rated to 300F and it says its safe for potable water. 6$ at home depot
  7. G

    Cut in cooler lining help

    Anybody think this appliance touch up paint is a bad idea? http://www.lowes.com/pd_320561-1168-5553_0__?productId=3185751
  8. G

    Cut in cooler lining help

    So, I was putting together a new cooler mash tun, and as I was cutting out the spout the cooler came with, I accidentally put a small slice in the bottom of the cooler. Not even sure if it went all the way through, but I would like to seal it up just in case. The cut is from an exacto knife and...
  9. G

    Book Trade

    Hey all, I have a copy of Extreme Brewing by Sam Calagione (Dogfish Head). I am looking to trade this book for a different homebrew book if anyone is interested. NOTE: This book is all extract with no all grain equivalents. Howver if you do extract this is a very good book. I am interested in...
  10. G

    CO2 tank question

    okay, cool, so should i really crank the one bolt that goes from the regulator to the tank, or would a hose be more likely? thanks for the help
  11. G

    CO2 tank question

    So I've been having parties where I get a keg or 2 and run them through my jockey box at about 45 psi (which keeps it from foaming up). I did so on a full tank last night and when I looked at it this morning the gauge said the tank was empty. I turned the tank off after the last keg was killed...
  12. G

    Jockey box foam problem

    I had my co2 set to about 12 psi. The keg was purchased cold and got progressively warmer throughout the night. There is a 3' 3/16 beverage line between the keg and the barb on the outside of the jockey box. Should I make this section of line shorter to keep it from getting warm? The coils at...
  13. G

    Jockey box foam problem

    Hey all, I built a jockey box with 25' of copper coil, about 3' of 3/16 beverage line and 5' of 3/16 line between the copper coil and the shank (5" shank). I got a keg of National Bohemian from a local liqour store and hooked it up to a d coupler with a co2 tank set to 12 psi. I am having a big...
  14. G

    Left Slap Pack Out

    Sounds good. Thanks for your help
  15. G

    Left Slap Pack Out

    I will take that advice for sure. Should I put it in the fridge now or keep it at the same temp? I plan to brew Friday
See more
Back
Top