cfc

Kettles, mashtun, propane burner, counterflow chiller, temp control, glass and plastic fermenters of various sizes, stir plate, pump, fold up stand, immersion chiller, taps, kegs, ph meter, kegs, taps, tap handles. Celina, TX Everything works perfectly, just need it gone, I don't brew anymore...

Selling some misc brewing equipment. See list below: Two stainless CFCs for sale: $80 each 2 chugged pumps: $50 Last straw bottle filler: $50 Blichmann beer gun: $40 2 Stir plates: $10 each Filter housing: $10 Local pickup preferred, but will ship at buyer's expense.

Just doing some brainstorming on how to reduce brewing equipment or have a device perform multiple functions. Along this line of thought; has anyone used a Counter Flow Chiller (CFC) or a plate chiller as a heat exchanger for mash temperature control instead of a HERMS coil or RIMS setup? It...

Hi HBT! I'm located in north Delaware. Images are below the descriptions. Looking for local pickup for the larger items, willing to ship the smaller items, but you pay. I am open to any and all questions about the items below, thank you. I have 2x SS Brew buckets. These are in decent shape...

Hello, I've been slowly upgrading my equipment and I'm finally getting around to building an actual stand. I have a CFC I've been using gravity for and want to move to using a pump. I've been searching around and every time I think I'm close to figuring it out, I confuse myself. The question I...

SF south bay area/monterey bay. Keggle with valve-$40 Inverted rubber-coated keg mash tun, with standard dome false bottom-$50 1/2bbl keg used as fermenter for 10gal batches- $30 1/4bbl keg used as fermenter for 5 gal batches- $30 Ball lock tri-clover adapter, used to convert kegs to...

Hi all! I have had a grainfather for a while now but have had a brewing hiatus. I find it hard to fully drain the CFC free of water. I picked up the CFC yesteday and realized that it had not drained completely, meaning that there has been water inside it or two or three months. My normal...

I am almost done with a 10 gallon eBIAB build, and I am wondering if I need to use a hop spider or not. I own one of the stainless mesh baskets that hang from the side of the kettle, but I would have to modify it to be able to keep my lid on for my steam condenser. I have only once had issues...

I am new to using a pump - I tested the Riptide I just bought with water and it works quite well. But my CFC will drastically throttle the exit velocity from the whirlpool arm, so after cooling my wort, I will have to swap a few hoses to remove the chiller from the fluid circuit. Does anyone...

I am converting my old gravity-fed CFC to be used with a pump and a whirlpool arm. I plan on using the SpinCycle whirlpool arm, which requires a 1/2" NPT male connection. I plan on just using camlock fittings, and I will use 1/2" ID silicon tubing on the input end of my chiller, but I have...

I am planning on slowly upgrading my brewing rig. The next step is to add a pump so I can more easily chill my beer and whirlpool - for both leaving trub behind and more easily adding whirlpool hops. If I remember correctly, my CFC copper tubing is 3/8" OD and 1/4" ID: I am assuming that it is...

To those ussing a SS CFC chiller, how many passes are you doing? I have a 25 foot SS chiller I use with a pump and about 50-54 degree chilling water. I recirculate until the boil kettle reaches pitching temp. But it takes nearly 30 gallons to do this. Is this extreme? Pump and chilling water...

I made a cfc out of 3/8" copper tubing and used a high temp rated hose for the outer plumbing on it. I have used it a few times and it cools batches very efficiently. I am just not brewing as much as I should and would like to lower my gear inventory. I am willing to ship and will listen to any...

SOLD! 25 ft. Counter Flow Chiller mounted inside a 5 gallon bucket. I built two only need one. Asking $50 plus shipping. PM me for a shipping estimate. Thanks! EDIT: Price Reduction!!!