Search results

Those bulkheads look almost identical to mine... I'm guessing stainlessbrewing gets them from Swagelok. That picture is not very clear. Are those gaskets nice and flat? I think I would also need the washer that his fittings come with. Also, I'm pretty sure mine are 3/8 inch...

Looks good but you should switch out the copper tubing for stainless for the reasons mentioned by others. Brass fittings won't be a problem since they are just on the lid and most likely won't have much, if any, contact with the beer. Here's a couple of photos of what I did for my 60 gallon...

They have motorized ball valves at http://www.oscsys.com/ (the commercial site run by the contributors to the brewtroller project). They are stainless and look pretty nice. $50 a pop. They seem to be out of stock but that might just be because the owners are currently at NHC. I think you can...

Yes, the linked pdf on the page indicates a max load of 8 amp/250 v for the output, so I suppose an ssr would be required.

Curious. Which model did you get and where did you get. I haven't had much luck tracking down prices on the Thomsens on-line.

I think this is the the thread you're referring to (the poster was in Sweden though). I'll read that for a while. Cheers.

I appreciate the safety concerns, but I've already used the barrel as an HLT without any issues. I couldn't detect any softening of the plastic at that temperature, or anything like that. The only difference will be that I'll be heating the water directly in the barrel, while currently I heat in...

Thanks for the info. That's interesting that you screwed to side port ball valve directly into the tank. I purchased flanges for side that I was going to screw into, but maybe your approach is simpler. Looks like you've got a silicone o-ring there too. If you get a chance to post photos of...

Hi Budzu, I will be using these inductors commercially as well. I will have 4 60 gallons, two 30 inch and two 24 inch. Would you happen to have any photos of what you did with the lid? Did you buy an extra lid just for CIP? Or do refit the spray ball into the lid each time you do CIP on a given...

It's 55 gallon.

Thanks, that's an idea. I'll have to see if I can find one of those adapters. What is the logic in putting the probe in-line with the pump? Is that what people usually do for their HLTs?

Hi All, I'm planning to convert an HDPE plastic drum into and electric HLT using a 5500 watt element. I have two questions about this. First, what would be the best way to secure the element to the drum. I know the element comes with a rubber gasket and I could use a simple locking nut on...

After researching I discovered that they do make 2 inch female npt to 1.5 inch tri-clamp adapters (rare) or you can use 2 inch female npt to 2 inch triclamp adapters mated to a 2 inch to 1.5 inch tri-clamp reducer. I'll go one of those routes.

I ordered two 60 gallon inductors. I requested the model with full drain and a 1.5 inch fpt connection at the bottom. I ended up receiving the version with the 2 inch mpt. I wanted to send them back but they told me to keep them since shipping was so high. Anyway, I'll see what I can do with...

Just ordered from amazon.com This is what wikipedia says that I think applies to my situation:

Yeah, I'll probably order from the US too. I have some stuff to pick up at the border anyway, so I'll pick up the elements at the same time.

Oh, one more question for you. How long does it usually take for the people you know doing 20+ gallons on 5500w to get a boil going? Yesterday I did a test and after 2 hours starting from 11°C water I was in the mid 90s, not quite boiling yet.

It's an industrial location. But I gather from what you're saying that the kettle wouldn't have worked if the power source was 3 phase? The label on the element gives a rating for 240 (4500) and another for 208 (around 3700). Is 208 always 3-phase? Also, since you're in Canada, do you know a...

Hi there, I don't have much electrical background so I was hoping I could ask a question about wattage and voltage of heater elements. I have a ~25 gallon kettle that is powered by a single 4500 watt element (rated at 240). As you can imagine, the kettle is seriously under-powered. Toda we...

I was thinking of installing it from the top, the cover of the drum. I figured the cooling source would be at the top and I could measure from the top as well. If I measure form the bottom, the wort at the top might be a lot warmer. A stainless cap would be ideal, I think. I haven't come...