Search results

Hazy Montage Hazy Ambrosia Hazy 3 Cs Hazy West Coast Fusion Hazy Juicy Fruitbomb

Hazy Montage Hazy Ambrosia Hazy 3 Cs Hazy West Coast Fusion Hazy Juicy Fruitbomb Thanks cornykeg!

I’m in!

I’m in! Thanks HBT

2 five gallon and 1 six gallon carboys in crates for safer carry 6gal $20 5gal $15 Take all three for $45 Local pickup in mid city Los Angeles

Is it no. 11 in this pic? You won't use it to rebuild a secondary regulator.

This is not a tap handle. It's a tryer handle for a 1926 probat coffee roaster. The roastmaster at our company is really into skateboarding and the old tryer handle was broken so I made this out or one of his old boards. The brass ferrule is turned from a garden hose fitting. Here is a tap...

1 what you are looking for is called SJ cable a at least 10guage, but it wont hurt if all you can find is 8(dont go the other way) b technically, it is called 3wire+g(there will be four conductors) black, red, white + green for ground c it comes as a cord, it wouldn't be safe to try to make this...

I have a very similar configuration on my kettle/whirlpool setup. You don't say what type of fermenter you are using, I have a conical, so maybe this won't apply, but this is what I do. I have a 1.5"triclamp to male camlock fitting which I attach to the racking port. When the wort is cooled I...

You could try removing the relief valve and cleaning it. You shouldn't have to hold it closed if it is functioning properly. I'm not familiar with that particular regulator and whether or not rebuild kits or replacement parts are available. Does this still occur if you adjust the low side...

A picture of the regulator might help. Are you referring to a manual prv with a pull ring? Or is it in the back of the regulator with no pull ring?

Certainly! This is an ordinary bitter I like to keep on rotation ten gallons 3.2% 10 lbs maris otter 1 lb crystal 40 .5 lb crystal 120 3oz East Kent Golding(whole cone) 60 min wyeast 1098 British ale

I make quite a few low abv session beers. Mostly those recipes for me are designed for low gravity rather than scaled down, but it should be fairly similar if you are building a session from an existing recipe. Some tricks I utilize: Scale the base malt primarily while still keeping the...

If you can turn a compression fitting without a wrench, then it is most certainly not air tight. I would start there. Maybe replace the 'olive' portion of the compression fitting with silicone, you could likely get that tight enough by hand.

Possibly the seal at the pick up tube is not tight and allowing air to be pulled in once the liquid level gets to the valve/pick up tube.

A bulkhead fitting isn't really necessary here. You could simply drill holes just larger than the OD of your tubing and push them thru the wall, similarly to how many run a co2 line into a kegerator.

I would be hesitant to use a submersible pump in my product water, that's just my opinion. How about one of these? https://www.google.com/search?q=flojet+bottle+pump&rlz=1CDGOYI_enUS734US735&oq=flojet+bo&aqs=chrome.3.69i57j0l3.7911j0j4&hl=en-US&sourceid=chrome-mobile&ie=UTF-8 I'm not sure it...

What about elevating the aquatainer and plumbing the RO to a float valve? like this https://www.amazon.com/dp/B012DU0ZAO/?tag=skimlinks_replacement-20 Then gravity feeding out of the aquatainer to the kettle.

It is possible, but will likely take some fiddling. The three leg clip holds the spring in the correct orientation and depth. If it's not aligned right the poppet may not close or open correctly. I've bent some similarly and they've worked fine, while others leaked and when I tried bending the...

Pics as promised Compressor exterior Evaporator interior Fermenters and grain storage