Search results

Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum

Help Support Homebrew Talk - Beer, Wine, Mead, & Cider Brewing Discussion Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.
  1. C

    Tennessee Nashville Area - Everything For All Grain Brewing

    still have any of this? I'm interested in hop spider.
  2. C

    Virginia All SS brewery liquidation - RVA

    in line for hop spider if it's still available
  3. C

    California 90 degree angled barb tail piece

    I'd take 10 for $2 each shipped
  4. C

    March Madness Sale + Keg Giveaway @ Kegconnection.com!

    Duke
  5. C

    New Jersey Two Ventmatic stainless faucets with 4" stainless shanks.

    I'll take em. Send me paypal info.
  6. C

    NEW StrangeBrew Elsinore Thread

    Doug, I am on a spending hiatus from brewing equipment for a while and was wondering about some modifications to the PH_sensor java file because I don't have a DS2450 converter. However I do have a MCP3008 ADC chip. I have it hooked up to the Pi and can read ph values from it and was...
  7. C

    NEW StrangeBrew Elsinore Thread

    Love this answer. Makes it clear. I got close with the settings: P=60 I=2 D=0 I had 10.5 gal in my HLT(Euro 13gal Keggle) it was 20deg outside and I have a 5500 Watt Stainless element I overshot a little and will use the info from Justin to fine tune some things next time.
  8. C

    Prototype Previews: Hopback and Heat Stick

    I've been testing my new system when I had time and I've left water in the hlt for over a week and no rusting on my SS Element. Thanks Bobby. PS. I did change the water when I brewed today! 😆
  9. C

    NEW StrangeBrew Elsinore Thread

    Doug, Just had my first Elsinore Brew. FANTASTIC! Didn't get to use all the features but what I did use was a breeze. Thanks so much for your hard work.
  10. C

    Two panel set up. Separate high voltage panel

    Success! Holding temp of 165 with auto mode and StrangeBrew Elsinore. thanks Jay
  11. C

    2x120v brewing - 1 switch, 1 contactor, 2 SSRs and 2 elements?

    I did it with 1 ssr and two contactors.
  12. C

    NEW StrangeBrew Elsinore Thread

    For those of you running Raspberry Pi's The new linux Kernal has a new Device Tree setup: For info read: http://www.raspberrypi.org/forums/viewtopic.php?f=28&t=97314 To get temp probes to work with a new update you must put this text in config.txt. first run sudo nano /boot/config.txt then...
  13. C

    AEB Keg Sale + 5 Gallon Giveaway - Kegconnection.com

    nice. thanks
  14. C

    Volume Sensing - What are You using

    I'll probably have to make something for the pi to able to read it. I was also thinking I could make my own cable. Do you know what kind of connections these use?
  15. C

    Volume Sensing - What are You using

    I just bought 2 of these for $75 ea. Hoping I can get them to work with my Pi. http://www.ebay.com/itm/like/301490551324?lpid=82&chn=ps
  16. C

    NEW StrangeBrew Elsinore Thread

    Here is the back of one of those boards.
  17. C

    NEW StrangeBrew Elsinore Thread

    Went to radio shack for small solder breadboards. Soldered resistor in then a series of pins for all my temp probes. On the other board I soldered breakout pins for 12 power, 5v power, ph, and gpio-therm pin out to my main panel. Used vinyl stand offs from HD to mount pi and sainsmart. Used a...
  18. C

    Spa Disconnect Question

    Yeah. That won't give you 240v. One hot leg will just give you 120v. Where did you get it?
  19. C

    Two panel set up. Separate high voltage panel

    Thanks. Got two ordered just in case I need 'em.
  20. C

    Two panel set up. Separate high voltage panel

    Had a chance to try and set things up yesterday and today but I had some trouble... I have one of these Teledyne Dual SSRs and I can't get the Raspberry pi side of the Low Voltage panel to activate the SSRs. When I put it in Manual mode and use the Auber DSPR1, the elements work fine...
Back
Top