Get your HBT Growlers, Shirts and Membership before the Rush!


Home Brew Forums > Home Brewing Beer > Automated Brewing Forum > Automatic electronic pilot light fof propane burners
Reply
 
LinkBack Thread Tools
Old 03-03-2013, 02:38 PM   #1
heapyjeepy
Feedback Score: 0 reviews
Recipes 
 
Join Date: Sep 2010
Location: Denver, CO
Posts: 22
Default Automatic electronic pilot light fof propane burners

I want to set up a gas fired HERMS/RIMS system that will be heated by my Bango propane burners.

Instead of using a gas fired pilot light, could I just use an electronic pilot lighter similar to a grill? Just push button and it lights the main burners?

The thing is, I would like to make my system as "turn key as possible" and not have to lite the gas pilots each brew. Also while Im at it, correct me if Im doing anything wrong with my gas system. If I were to go with a gas pilot it would go between the Two stage Reg and Furnace valve

LP Tank->30PSI Reg->Manifold->1/2PSI Two stage Reg-> Furnace Valve->LP Orfice for Banjo Burner-> Banjo Burner

__________________
heapyjeepy is offline
 
Reply With Quote Quick reply to this message
Old 04-02-2013, 06:46 AM   #2
dose5150
Feedback Score: 0 reviews
Recipes 
 
Join Date: Feb 2013
Posts: 5
Default

I thought about doing the same thing with my burners, but I could not make it work fully automated. I decided to go with a standing pilot for simplicity. Thought about doing a intermittent pilot, then realized I would need a furnace module. And I'm sure you already know this, but you'll need low pressure orifice's on your banjo burners as well.

__________________
dose5150 is offline
 
Reply With Quote Quick reply to this message
Old 04-02-2013, 07:05 AM   #3
conneryis007
Feedback Score: 0 reviews
Recipes 
 
Join Date: Nov 2009
Location: Keystone, CO
Posts: 262
Liked 22 Times on 20 Posts
Likes Given: 15

Default

Which furnace valves are you thinking of using? Are you going to be PID controlling some of your burners? Did you find furnace valves that operate with high pressure propane or did you mean to write low pressure?

My set-up uses the honeywell vr8200 valves and I have to manually press and hold a pilot button on the valve while lighting each burner. These valves have the pilot and thermocouple (which senses if the pilot blows out) built right in. This takes 30 seconds to light all the pilot lights. The standing pilot light makes the rest of the set-up so easy.

Assuming you are going to use PIDs for temp control:
With your idea of the grill push button, what would you use to ensure that the grill lighter fires at the same time the gas turns on each time it cycles on/off?
They make fancy electronic ignitions, but I was under the impression that they are a bit spendy.

__________________

Never underestimate how much assistance, how much satisfaction, how much comfort, how much soul and transcendence there might be in a well-made taco and a cold bottle of beer.

conneryis007 is offline
 
Reply With Quote Quick reply to this message
Reply



Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
Shielding for pilot burners / brewstand jcaudill Brew Stands 10 04-10-2012 11:59 AM
Pilot Light Setup - 10 tip jet burners canyonbrewer Brew Stands 3 04-19-2011 11:42 PM
Pilot mounting on BG14 burners Eigenbrau Brew Stands 0 08-10-2010 10:34 PM
Gas Burners with Love TS and Pilot Light Demo MNBugeater Equipment/Sanitation 106 01-26-2010 07:05 PM
Pilot Light with Honeywell Y8610U intermittent pilot kit bkloos Brew Stands 12 11-24-2009 09:00 PM



Newest Threads

LATEST SPONSOR DEALS