Kegconnection Complete Starter Kit and More Giveaway!


Home Brew Forums > Home Brewing Beer > Equipment/Sanitation > Sight Tube leaking - Help

Reply
 
LinkBack Thread Tools
Old 03-28-2008, 04:13 PM   #1
riored4v
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2008
Location: Aurora, CO
Posts: 1,334
Liked 9 Times on 9 Posts

Default Sight Tube leaking - Help

Need some assistance with my sight tube I installed in my keggle.

I filled it up last night to check for leaks and the only thing leaking was the sight tube. It appears to be leaking from where it goes through the keg and also where the sight tube itself is inserted into the T.

I tried adding an extra washer on the outside and inside of the keg, but i still seem to be leaking a tad.

I also tried tightening and loosening the sight tube and didn't seem to stop the leaks.

Any advice would be appreciated.

__________________
Resistance Brewing Co.
Resist Crap, Drink Craft!
riored4v is offline
 
Reply With Quote Quick reply to this message
Old 03-28-2008, 04:16 PM   #2
GilaMinumBeer
In yo' garage, steelin' yo parts.
HBT_LIFETIMESUPPORTER.png
Feedback Score: 0 reviews
 
GilaMinumBeer's Avatar
Recipes 
 
Join Date: Jan 2008
Location: Oblivion
Posts: 47,031
Liked 4628 Times on 4311 Posts
Likes Given: 57

Default

Mine dribbles a bit until the kettle warms up.

Keep in mind too, that you can overtighten these things and trash the gaskets.

__________________
GilaMinumBeer is offline
 
Reply With Quote Quick reply to this message
Old 03-28-2008, 04:20 PM   #3
riored4v
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2008
Location: Aurora, CO
Posts: 1,334
Liked 9 Times on 9 Posts

Default

I thought I may have overtightened the first time around because the it was still a really lose fit on the keg. I came back on here and read that some people added washers to fix it, so i tore it back apart and the gaskets still appeared to be in good shape so I tried it again w/o tightening to hard this time, just to get a nice snug fit on the keg and it still dribbled.

__________________
Resistance Brewing Co.
Resist Crap, Drink Craft!
riored4v is offline
 
Reply With Quote Quick reply to this message
Old 03-28-2008, 04:21 PM   #4
Bobby_M
Vendor and Brewer
HBT_SPONSOR.png
Vendor Ads 
Feedback Score: 2 reviews
 
Bobby_M's Avatar
Recipes 
 
Join Date: Aug 2006
Location: Whitehouse Station, NJ
Posts: 21,831
Liked 905 Times on 602 Posts
Likes Given: 26

Default

My best advice on weldless fittings is to install the inside parts first. Put the Oring on the nipple, slide a few washers on, then tighten the coupling on. If the Oring is still over threads, you need more washers. If the Oring sits over threads, the half-a$$ workaround is to fill the threads in with teflon tape. Not my prefered method if you're asking.

On the sight into the fitting piece, what did they use as a ferrule under the nut? Oring? You can add another Oring in there...

__________________
BrewHardware.com
Sightglass, Refractometer, Ball Valve, Weldless bulkhead, Thermometer, Decals, Stainless Steel Fittings, Compression Fittings, Camlock Quick Disconnects, Scale, RIMS tube, Plate Chiller, Chugger Pump, Super Clear Silicone Tubing, and more!

New Stuff?
Bobby_M is offline
 
Reply With Quote Quick reply to this message
Old 03-28-2008, 04:30 PM   #5
riored4v
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2008
Location: Aurora, CO
Posts: 1,334
Liked 9 Times on 9 Posts

Default

I'm not sure of the exact word, but it's some sort of compression fitting for the sight tube. It slides on the tube, and then a nut squeezes down onto it as you tighten it to the T.

The O-ring for the nipple should be against the keg correct? Basically what you're saying is that when I slide the nipple through the keg to the outside, i want to only really see maybe one thread poking through the outside? Should I put more washers on the inside or outside? Right now I have 2 washers inside and outside.

__________________
Resistance Brewing Co.
Resist Crap, Drink Craft!
riored4v is offline
 
Reply With Quote Quick reply to this message
Old 03-28-2008, 08:11 PM   #6
riored4v
Feedback Score: 0 reviews
Recipes 
 
Join Date: Jan 2008
Location: Aurora, CO
Posts: 1,334
Liked 9 Times on 9 Posts

Default

any other ideas for fixing this?

leaving work here in a couple hours and want to have a few ideas to take home so i can hopefully get it fixed.

__________________
Resistance Brewing Co.
Resist Crap, Drink Craft!
riored4v is offline
 
Reply With Quote Quick reply to this message
Reply


Quick Reply
Message:
Options
Thread Tools


Similar Threads
Thread Thread Starter Forum Replies Last Post
racking cane sight tube android Equipment/Sanitation 5 04-13-2009 10:10 PM
Sight tube - Kettle or HLT? Ryan_PA Equipment/Sanitation 4 03-02-2009 04:52 PM
putting a sight tube on my MLT. This ok? Nightbiker Equipment/Sanitation 2 12-08-2008 05:20 PM
Sight Tube Spoonta DIY Projects 2 01-08-2008 10:12 AM
term to use w/ zymco sight tube robmee Equipment/Sanitation 0 08-18-2005 03:10 AM