• Please visit and share your knowledge at our sister communities:
  • If you have not, please join our official Homebrewing Facebook Group!

    Homebrewing Facebook Group

Squeezing the Bag

Homebrew Talk

Help Support Homebrew Talk:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

goforevercrazywithit

Well-Known Member
Joined
May 26, 2012
Messages
53
Reaction score
4
Location
502
What's the deal here?

I'm putting together my first BIAB cook and I'm hearing over and over about squeezing the bag after it's removed from the mash.

During extract brewing, I had always heard that squeezing the bag was bad for business as it would release a bunch of unwanted tannins into the brewpot.

So what's the verdict? I'm planning up a Cream Ale where the bag will have 6-row barley and some corn from a cereal mash.

To squeeze or not to squeeze? :confused::goat:
 
What's the deal here?

I'm putting together my first BIAB cook and I'm hearing over and over about squeezing the bag after it's removed from the mash.

During extract brewing, I had always heard that squeezing the bag was bad for business as it would release a bunch of unwanted tannins into the brewpot.

So what's the verdict? I'm planning up a Cream Ale where the bag will have 6-row barley and some corn from a cereal mash.

To squeeze or not to squeeze? :confused::goat:

Squeeze away brulosophy guy de-bunked that myth too. Ive been squeezing for a couple years now with no off flavors. Your not extracting anything thats not already there.
 
Go ahead and squeeze if you are impatient. I suggest taking the easy route and let gravity do the work by letting the grain bag drain and drip for 20 - 30 minutes as your wort comes to a boil. Leaving the grain bag to hang above the kettle on a ratchet pulley works well, or placing the bag in a bucket with something to elevate it off the bottom will work well.

I have found after a patience testing free drain, there's not much left to be concerned about.
 
Letting it hang will work if you have previously accounted for it. If I do this my efficiency is in the upper 60's. When I squeeze my efficiency is generally upper 70's or low 80's. Lots of ways to skin this cat but which one will be most consistent for the op? That's for him to figure out I guess.
 
It would seem to me this "squeeze" controversy could be easily tested. Just drain the bag without squeezing, then place the bag in another pot and squeeze the bejesus out of it. Sample both pots, cool the samples down to room temperature, and taste them side by side. If the squeezing extracted tannins it should be evident in the wort. No need to wait for the finished beer which will have other factors influencing the taste such as alcohol and carbonation that could possibly mask the tannin comparison.

I will be brewing this weekend and will try this experiment. Since wine tasting and drinking has been a hobby of mine for some 40 years I expect I will be able to pick out tannins from the other wort flavors.

TomVA
 
It would seem to me this "squeeze" controversy could be easily tested. Just drain the bag without squeezing, then place the bag in another pot and squeeze the bejesus out of it. Sample both pots, cool the samples down to room temperature, and taste them side by side. If the squeezing extracted tannins it should be evident in the wort. No need to wait for the finished beer which will have other factors influencing the taste such as alcohol and carbonation that could possibly mask the tannin comparison.

I will be brewing this weekend and will try this experiment. Since wine tasting and drinking has been a hobby of mine for some 40 years I expect I will be able to pick out tannins from the other wort flavors.

TomVA


Makes perfect sense to me. I'll be interested to hear what you discover.
 
I'd be interested in an experiment to gauge total wort recovered by just letting the bag drain for 30 minutes vs squeezing like a mad man.

I have a hunch there is not much gained if any squeezing vs a patient drain of say 30 minutes.
 
I'd be interested in an experiment to gauge total wort recovered by just letting the bag drain for 30 minutes vs squeezing like a mad man.

I have a hunch there is not much gained if any squeezing vs a patient drain of say 30 minutes.


I actually tested this and the answer is "it depends on the bag and the grain bill"

Your bags are by FAR the best gravity drainers and 30 minutes resulted in about 2 cups difference in finished wort volume.

The brew bag after 30 minutes was nearly 0.75 gallons short and required squeezing to get the rest. I suspect the two nylon straps inhibit drainage.

A paint strainer bag was about halfway in between.

I also found that the "squeezed wort" seemed to have a higher concentration of sugars than gravity drained wort. I didn't test this for repeatability though. My theory for this is that, like a sponge holding salt after a saltwater dip, grain will always retain some sugars under the weight of gravity. So squeezing liberates water faster and more sugar stays in solution due to the higher volume of water coming out.

The efficiency difference was about 6% on my system.

So I do attribute a small lautering efficiency increase to squeezing, I'll usually do a combination of hanging for about 20 minutes then squeezing the rest out.

Grain bills with oats or flaked adjuncts retain water like crazy and really do need to be squeezed.

The old astringency issue is a non issue. It just doesn't happen. Astringency is the result of a high ph coming into contact with the grain husks, or heating them too much and extracting tannins. Tannins are a water soluble compound under specific conditions (pH and temperature), and are otherwise not soluble.

Saying "squeezing can extract tannins" is the same thing as saying "I can dissolve a bone in my soup if I stir it hard enough"

Sure bone will dissolve but you have to boil it long enough in the correct chemical conditions.

I've squeezed nearly every batch I've ever made in a bag, more than 100, and I've never once experience astringency.
 
I've also found that squeezing vs hanging depends on the grain bill. Lighter grain bills with less wheat or rye seem to drain fine in the time it takes to get to a boil, but larger ones, and those with higher amounts of wheat or rye seem to take longer to drain, so I squeeze.

I'm putting together a BIAB Wheatwine to brew the Sunday after turkey day (while I also brew a tripel on my 3-vessel system) and I plan to squeeze AND (for the first time) try a dunk-sparge.

When I make the wheatwine, I'm going to check the SG on the wort in the kettle, the wort in the "last squeezings" and the final SG to see what differences, if any, there are.

@jimmykx520, I'd also like the link to the specific xbmt at brulosophy that debunked tannin extraction from squeezing - I could not find any reference to it.
 
@jimmykx520, I'd also like the link to the specific xbmt at brulosophy that debunked tannin extraction from squeezing - I could not find any reference to it.


I don't think he ever actually tested that. Brukaiser discusses tannins on his website extensively and talks about how they can be extracted. There's simply no way it can happen from squeezing.. See my post above, that's pretty much a summary of Kai's explanation.
 
I normally sparge in 2 steps, squeezing in between each one. TBH squeezing is one of my least favourite brewing tasks (makes a big mess) but my overall process normally gives me low 80s efficiency and I like that. Would be interesting to know whether squeezing is needed after each sparge or just once at the end.
 
What's the deal here?

I'm putting together my first BIAB cook and I'm hearing over and over about squeezing the bag after it's removed from the mash.

During extract brewing, I had always heard that squeezing the bag was bad for business as it would release a bunch of unwanted tannins into the brewpot.

So what's the verdict? I'm planning up a Cream Ale where the bag will have 6-row barley and some corn from a cereal mash.

To squeeze or not to squeeze? :confused::goat:

I'm a noob at BIAB but to my under standing you have to reach way higher temps than 150 degrees or 170 at a mash out, for any tannin's to develop in your grains?
I would like to know at what temp you are at risk of developing Tannin's
 
I'm a noob at BIAB but to my under standing you have to reach way higher temps than 150 degrees or 170 at a mash out, for any tannin's to develop in your grains?
I would like to know at what temp you are at risk of developing Tannin's

Accidentally let my last mash go to 180. Quickly cooled and was only over 150 for ten minutes. What should I expect?
 
Accidentally let my last mash go to 180. Quickly cooled and was only over 150 for ten minutes. What should I expect?


Beer lol. Depnds on when the temp soared to 180. If you mash was at proper temps for a period before that, conversion likely happened quickly. When did the temps soar? You likely only need 10 or 20 minutes to convert most of the starches.

Depending on your PH, the excessive temps MAY HAVE EXTRACTED tannins.

I suggest rdwhahb, what's done is done and your likely ok IMHO.
 
Accidentally let my last mash go to 180. Quickly cooled and was only over 150 for ten minutes. What should I expect?

I once accidentally let mash temp get over 165, but it was after 30 minutes. A couple neighbors thought it was my best brew ever.
 
I don't think he ever actually tested that. Brukaiser discusses tannins on his website extensively and talks about how they can be extracted. There's simply no way it can happen from squeezing.. See my post above, that's pretty much a summary of Kai's explanation.

Yeah, I know that squeezing doesn't extract tannins - it's a function of temperature, pH and time - but since dude said Marshall debunked it, I just wanted to see the source for myself - too many times folks accept someone's words without actually seeing what backed them up, I don't remember EVER seeing any xBmt about squeezing grains. :mug:
 
I usually squeeze until my hands hurts then let it drain over a pasta strainer in a bucket and get up to 2-3 additional litres. Don't forget to increase heat when you add your wort to not kill the boil tho.
 
I occasionally BIAB at home to test an idea on a 1 gallon setting before running a 1 bbl + batch. After I pull out the bag and let it drain until I get only occasional drips I'll then set the bag in a strainer over a separate small pot while I brings wort up to a boil. By the time my wort is at about 205-210 (just under a boil) I'll have another 6-10 fl oz that drained from the bag on the smaller pot without squeezing and will just dump it into my kettle. Not much fluid but it has helped to balance out gravity and final yields on these little 1 gal batches without extracting tannins
 
So I completed the tannin taste test I described above. I drained the bag over the mash pot without squeezing until it slowed to a drip, then placed the bag in a strainer over a bowl and squeezed the devil out of it, both by pressing it with an inverted bowl and by hand until I couldn't get any more out of it. I then sampled the un-squeezed wort in the mash pot and the squeezed wort in the bowl, cool the samples down to room temperature, and taste them side by side in wine glasses. The squeezed wort was just very slightly darker, sweeter, and more flavorful, but I could not detect any tannins in either sample.

From now on I will squeeze the bag while the wort is heating to boil.

TomVA
 
I have noticed more fine particulates in the squeezed wort than the non-squeezed. IF your crush was too fine for example and small fragments of husk were squeezed through the bag membrane into your boil then wouldn't tannins be a result of boiling this debris? When gravity draining, the grain acts as a strainer just as it does in a mashtun and you get less cloudy wort. I don't know if this actually has any effect on the flavor of the final beer, but would likely result in more trub after the particulates settle out of suspension.

As far as efficiency goes, I think squeezing results in more sugars being extracted. If you squeeze while the grain is still close to mash temperature then the viscosity of the wort will be lower and you will get more out of the grain. If you allow the bag to drip for a period of time first before squeezing, then the grain will be at a lower temperature and more of the sugars will remain stuck to the grain. Ive done both methods and notice a difference in the spent grain, where the bag that was squeezed while hot has fairly "clean" spent grain, and the drip bag method had more "sticky" spent grain representing sugars still coating the grain.
 
I have noticed more fine particulates in the squeezed wort than the non-squeezed. IF your crush was too fine for example and small fragments of husk were squeezed through the bag membrane into your boil then wouldn't tannins be a result of boiling this debris? When gravity draining, the grain acts as a strainer just as it does in a mashtun and you get less cloudy wort. I don't know if this actually has any effect on the flavor of the final beer, but would likely result in more trub after the particulates settle out of suspension.

As far as efficiency goes, I think squeezing results in more sugars being extracted. If you squeeze while the grain is still close to mash temperature then the viscosity of the wort will be lower and you will get more out of the grain. If you allow the bag to drip for a period of time first before squeezing, then the grain will be at a lower temperature and more of the sugars will remain stuck to the grain. Ive done both methods and notice a difference in the spent grain, where the bag that was squeezed while hot has fairly "clean" spent grain, and the drip bag method had more "sticky" spent grain representing sugars still coating the grain.


No offense intended, but There is a lot of misinformation in this post and in this thread in general.

Increased temperature has no effect on lautering efficiency whatsoever. The viscosity of the liquid has zero effect on the amount of sugars extracted. Brukaiser proved this both theoretically and experimentally, and the results are on his website. You can sparge/lauter with room temperature water and be just fine.

As far at the fine crush issue: crushing should not produce small husk particles, unless you are actually grinding your grain to flour. The husks will remain mostly in tact even on a grain mills finest setting, which is where I keep mine. Only the endosperm is being crushed.

If you do get a large amount of husks into your boil kettle then yes you could theoretically get some tannins, but that shouldn't happen unless you've done something wrong with your grain treatment.

The reason your hung bag was stickier than your squeezed bag was that your hung bag had time for wort to evaporate off of it leaving sticky sugar behind, while the squeezed bag was still wet. I bet if you took your squeezed bag and put it in a bucket for 30 minutes it would be just as sticky.
 
No offense intended, but There is a lot of misinformation in this post and in this thread in general.

Increased temperature has no effect on lautering efficiency whatsoever. The viscosity of the liquid has zero effect on the amount of sugars extracted. Brukaiser proved this both theoretically and experimentally, and the results are on his website. You can sparge/lauter with room temperature water and be just fine.

As far at the fine crush issue: crushing should not produce small husk particles, unless you are actually grinding your grain to flour. The husks will remain mostly in tact even on a grain mills finest setting, which is where I keep mine. Only the endosperm is being crushed.

If you do get a large amount of husks into your boil kettle then yes you could theoretically get some tannins, but that shouldn't happen unless you've done something wrong with your grain treatment.

The reason your hung bag was stickier than your squeezed bag was that your hung bag had time for wort to evaporate off of it leaving sticky sugar behind, while the squeezed bag was still wet. I bet if you took your squeezed bag and put it in a bucket for 30 minutes it would be just as sticky.

Can I ask why tannins are so bad? Bad flavor?
 
Back
Top