Brew Bucket owners - What Mini Fridge are you using ?

[steveoatley]

Hey all you Owners of the SS Brew Bucket

http://www.ssbrewtech.com/collections/fermenters/products/brewbucket

What Mini Fridges are yous guy putting them in for Temp control ?
( or wine coolers )

I was hoping there was a specific Make/Model that did not need any Collar
to make it work ??? Looks like 4.4 Cu ft is right ?

I am not having a lot of luck - as i can only measure the inside of Mini Fridges
that are actually in stock as Home Depot or sears - and the picking are slim

Thanks
Steve

 

[tedzap]

Good post, I have the same question!

 

[tedzap]

Avanti 2.5 seems to work with cutting mods and blow tube

 

[steveoatley]

Any one else find a mini Fridge that fits your Brew Bucket well ?

Thanks

S

 

[gromitdj]

According to the response I got over on a Thread in the BrewPi forum, the Haier HNSE045 will work if you remove the door shelving. Which I believe to be glued on. Which means cutting the plastic and insulation off.

 

[steveoatley]

Donnie

Thanks for the link - very helpful

It just seems that when i find a make/model that fits

It becomes discontinued.....The Haier is now discontinued.

http://www.amazon.com/dp/B0050GXY02/?tag=skimlinks_replacement-20


Steve

 

[tjosborne]

I'm willing to bet that new model will work just as well.

 

[tracyk]

The Igloo 4.5 cu ft. cooler is just a little to small but the dimensions on the inside are 11.75" x 28" for anybody that is looking.

 

[gromitdj]

Donnie

Thanks for the link - very helpful

It just seems that when i find a make/model that fits

It becomes discontinued.....The Haier is now discontinued.

http://www.amazon.com/dp/B0050GXY02/?tag=skimlinks_replacement-20


Steve

I found mine on craigslist for $60. I just don't have the Ss Brewbucket.

 

[YellowRiver]

I'm not going to be much help except for hope.
I picked up a craigslist winefridge for 70 bucks to create a fermentation chamber.
I measured it prior to getting the BrewBucket, fitting in was a huge part of the decision. I had to only remove the slide in shelves, it fit my 6.5G carboy with blow-off, but was very tight.
The capacity says 130L/4.6 Cft, the compressor is a HUAYI.
"Chateau Ste Michelle Refrigerator Cooler" Distributed by Asian Products Supply, St Paul MN

 

[steveoatley]

I'm not going to be much help except for hope.
I picked up a craigslist winefridge for 70 bucks to create a fermentation chamber.
I measured it prior to getting the BrewBucket, fitting in was a huge part of the decision. I had to only remove the slide in shelves, it fit my 6.5G carboy with blow-off, but was very tight.
The capacity says 130L/4.6 Cft, the compressor is a HUAYI.
"Chateau Ste Michelle Refrigerator Cooler" Distributed by Asian Products Supply, St Paul MN

Thanks for the info...

I'll start looking

S

 

[YellowRiver]

The advantage of the wine fridge is that you don't have to deal with the freezer shelf. The disadvantage is that the compressor isn't as powerful and it takes me 12+ hrs to coldcrash from 72F to 40F.

To be fair I do not know how many bottles of wine it would hold and that seems to be how these things get marketed.

I did put in a STC1000 controller, bi-passed the thermostat(with a stickered warning upon my demise) and added a flex-a-watt heater section. Also serves as a carbing/conditioning chamber for my bottles when the room is cold.

The bottom inside of mine is 11.25" from side of compressor shelf to edge and about 17.25" wide. the glass door has about 1/2" total from glass to end of seal.

 

[tedzap]

I just ordered two of the Haier 150 can beverage coolers, model HBCN05FVS from Sam's Club.

When closing the door it touches the temperature display on the front of the bucket, but because the display is rubber mounted it just straightens it out against the glass. This would be acceptable, but I figure that I will have a thermocouple in that location anyway (which won't stick out).

I have one of these and when I realized they would fit I started searching for more... but it looks like they are at the end of their lifecycle. The only decent price I found was Sam's ($169), but they were sold out. Today I noticed that they had a quantity of 5, so I went ahead and put in an order. Now they have 3

 

[tedzap]

I just ordered two of the Haier 150 can beverage coolers, model HBCN05FVS from Sam's Club.

When closing the door it touches the temperature display on the front of the bucket, but because the display is rubber mounted it just straightens it out against the glass. (My SSBB is the brewmaster edition with the temp display). This would be acceptable, but I figure that I will have a thermocouple in that location anyway (which won't stick out).

I have one of these and when I realized they would fit I started searching for more... but it looks like they are at the end of their lifecycle. The only decent price I found was Sam's ($169), but they were sold out. Today I noticed that they had a quantity of 5, so I went ahead and put in an order.

 

[tedzap]

I just ordered two of the Haier 150 can beverage coolers, model HBCN05FVS from Sam's Club.

When closing the door it touches the temperature display on the front of the bucket, but because the display is rubber mounted it just straightens it out against the glass. This would be acceptable, but I figure that I will have a thermocouple in that location anyway (which won't stick out).

I have one of these and when I realized they would fit I started searching for more... but it looks like they are at the end of their lifecycle. The only decent price I found was Sam's ($169), but they were sold out. Today I noticed that they had a quantity of 5, so I went ahead and put in an order. Now they have 3

I really like the glass front door, it will show off the fermenter.

 

[tedzap]

sorry about the multiple posts, I was trying to edit it and something odd happened. Does anyone know how to remove a post?

 

[brewbama]

I just use a reg size fridge

 

[steveoatley]

I just ordered two of the Haier 150 can beverage coolers, model HBCN05FVS from Sam's Club.

When closing the door it touches the temperature display on the front of the bucket, but because the display is rubber mounted it just straightens it out against the glass. This would be acceptable, but I figure that I will have a thermocouple in that location anyway (which won't stick out).

I have one of these and when I realized they would fit I started searching for more... but it looks like they are at the end of their lifecycle. The only decent price I found was Sam's ($169), but they were sold out. Today I noticed that they had a quantity of 5, so I went ahead and put in an order. Now they have 3

I really like the glass front door, it will show off the fermenter.

Thanks for the info

I just tried Sams club - and they are now out of stock on line

Sams had the best price - everyone else has them for $300 or more !

So it must be a popular size for those SS Brew Buckets

EDIT: - and now there are none - anywhere in Sam's

S

 

[steveoatley]

Anyone else find something that fits your SS Brew Bucket

with out too much modification....??

Thx
S

 

[steveoatley]

Has any of yous Brew Bucket owners tried this one ?

http://www.homedepot.com/p/Magic-Ch...gerator-in-Stainless-Look-HMBR440SE/205397955

It seems too small - with the hump in the back
But looks to be tall enough

Thx
S

 

[steveoatley]

bump

anyone have a model that fits good ?
with out modification ?

thx

S

 

[Spartan1979]

Has anyone come up with anything else?

 

[woo_pig]

I'm currently looking at a mini or a chest. I have been noticing that a small chest is about the same price or cheaper than a bigger mini (Smedium).

 

[steveoatley]

Sorry !!! I forgot to post, that i found something

I did find a good option at Sams Club

http://www.samsclub.com/sams/126-can-dsv-in-club-886159/prod18910248.ip

Fits SS Brew Bucket
Fits Glass 6.5 g Carboy
Fits Plastic Brew Bucket

No modification needed to fit - just take out the glass shelves

Here is a pic, with the SS brew Bucket

 

[steveoatley]

Here are Better Pics
Found on my phone - does anyone really own a camera any more ?

Testing each Fermentor.
These have no reflections - you can see that there is plenty of room

Brew Bucket
6.5 gal Carboy
SS Brew Bucket - 7 gal

I do not know why my pics upload sideways - there are not that way ?

Hope this helps

Steve

 

[woo_pig]

Here are Better Pics
Found on my phone - does anyone really own a camera any more ?

Testing each Fermentor.
These have no reflections - you can see that there is plenty of room

Brew Bucket
6.5 gal Carboy
SS Brew Bucket - 7 gal

I do not know why my pics upload sideways - there are not that way ?

Hope this helps

Steve[/What size is that. How many bottles will it hold .Sorry the link you posted isn't working for me .

 

[steveoatley]

Here is the description from the Sam's website

Tramontina 126-Can Beverage Center
by Tramontina | Item #: 886159 | Model #: 80901/502DS |

Here is the link again

http://www.samsclub.com/sams/126-can-dsv-in-club-886159/prod18910248.ip?sprodId=prod18910248

126 Can bev cooler

Hope this helps

Steve

 

[tjosborne]

Would a spidel fermentor fit in there? 13.5 diameter

 

[steveoatley]

Would a spidel fermentor fit in there? 13.5 diameter

TJ

I don't think so
I do not own a Spidel, so i can't say for sure

I measured the bottom - Hump to Door and got 12 inches
Now the cooler gets bigger toward the top
I measured from the CHILL plate at the back to the door - 16.5 inches

If you have an empty Spidel - take it to Sams Club, mine local Sam's has one out of the
box on display

I hope that was helpful
S

 

[woo_pig]

I might of got lucky my LHBS just upgraded therey eat fridge from something like this to a big commercial one. He said he'll sell me the old one for a pretty good price.